What is the general state of Stress?
Q: What are the principal stresses? How can they be determined?
A: Principle stresses can be defined as the maximum or minimum normal stresses on a specific plane. The…
Q: What is the relationship between the ?distance from neutral axis and stress
A: The stress, s, in the element a distance, y, from the neutral axis i s proportional to the…
Q: What is torsional stress?
A: When the twisting load is applied over the body or a shaft, then the shear stress generated is…
Q: What is Circumferential Stress?
A: Circumferential Stress When pressure inside thin pressure vessel exceeds it exerts force from inside…
Q: What happens if the principal stresses at a critical point in the material?
A: First, define the critical point. Critical points are those points in the given plane where the…
Q: 1. What is the difference between direct and shear stress?
A: We are suppose to solve only one question. Please post other question as a separate question.
Q: Sketch the relationship between the stress and the number of cyclic loading applied on an element
A:
Q: What is the influence of the strain on the triaxial stress if it is subjected to the material?
A: The strain of a specimen is defined as the deformation of specimen per unit length of that specimen.…
Q: 5-in stress strain curve the engineering stress will decrease after the tensile strength point?
A: Given data To draw the stress strain diagram.
Q: Define the term Stress Concentrations?
A: Stress concentration is a location in a member under load where the magnitude of stress is…
Q: What is Longitudinal Stress?
A: The stress produced along the length of an object due to the presence of forces which are equal and…
Q: What is the effect of an eccentric loading?
A: Eccentric loading: The eccentric loading is a type of loading on beams and columns in which load…
Q: Describe the State of Stress caused by the combined loadings?
A: Combined loading: In combined loading conditions, the specimen/ component is subjected to various…
Q: What is the biaxial stress?
A: Biaxial stress can be explained as when stresses are acting on an element in X and Y direction, and…
Q: What does the region of strain hardening cause?
A: The working of the metals below their recrystallisation temperature is known as cold working…
Q: How can the ductility of material be specified?
A: Ductility is the material’s property to undergo large plastic deformation (permanent type) after the…
Q: What is the dynamic stress?
A: Stress: Stress is defined as the developed force in the specimen per unit area when that specimen is…
Q: Rank the curves based on the change in strain that occurs during the necking phase. Rank the curves…
A: Various stages shown on the stress-strain diagram are: Proportionality limit Plastic limit Necking…
Q: What is the Conventional Stress-strain show with a diagram?
A: A ductile material subjected to a tensile test passes through different stages before reaching the…
Q: What is the Average Compressive Stress?
A: Forces acting perpendicular to the cross section of the body are normal forces. They can be either…
Q: Characterize the general state of stress at a point?
A: The general state of stress at a point can be characterized in the following way: 1.Three…
Q: Besides normal tensile stress, list three other types of material stresses? Are these typically all…
A: Stress: Stress is defined as the internal resistance per unit area of cross-section. There are…
Q: . What is the longitudinal stress developed in
A: To find Longitudinal stress
Q: What is the difference between direct and shear stress?
A: The difference between direct and shear stresses are: 1. Direct stresses are induced in the body…
Q: Why should stress not exceed the material by design?
A: Every component is designed based on working stress which will acts on the component during its…
Q: How are the Normal and Shear Stress Components used?
A: Normal stress is defined as stress which induced due to the outside force acting normally on a…
Q: Describe the Maximum Shear Stress Theory?
A: According to Maximum Shear stress Theory or Tresca's Theory of Failure: "A component subjected to…
Q: The ultimate tensile stress of mild steel compared toultimate compressive stress is O more O less O…
A: Concept: 1)Mild steel is a ductile material. 2) For ductile materials, ultimate strength in tensile…
Q: Identify shortly the parts of the stress-strain. Briefly explain each part.
A: Stress is define as the ratio of restoring force and the cross section area. It's formula is σ=P/A…
Q: 5-In stress strain curve the engineering stress will decrease after the tensile strength point?
A: To give proper explanation of the above statement.
Q: Briefly explain the state of plane stress and plane strain.
A: Plane stress is a two-dimensional condition of stress in which the entire amount of tension is…
Q: Describe the hydrostatic stress?
A: When a force is imparted on a body, an internal resisting force is set up into the body, impeding…
Q: differentiate allowable stress , ultimate stress and actual stress
A: To find : differentiate allowable stress , ultimate stress and actual stress
Q: What is the linear variation in shear stress along any radial line?
A: For a linear-elastic material, the shear stress varies linearly with shear strain.
Q: The tangential stress is produced twice that of the longitudinal stress in thin walled pressure…
A:
Q: Define stress . What are the causes and reactions to stress ?
A: Given Stress To find Stress definition Cause for the reaction of stress
Q: With what is Stress associated and how?
A: Please Specify the question in more detail, sir. But in general, it can…
Q: A typical value for the yield stress of mild steel would be? Select one: O a. 200 GPa O b. 100 MPa O…
A: Option c is correct.
Q: What is plane stress?
A: Let us consider a plate in x-y plane stress=σxτxyτxzτyxσyτyzτzxτzyσzPlane stress = σxτxy0τyxσy0000
Q: What is Residual Stress?
A: Whenever a body is deformed beyond the elastic limit it is unable to regain its initial shape. Due…
Q: When does the plane stress occur?
A: Plane stress is defined as the state of a material when one of the stress components are acting on…
Q: How do the magnitude and direction of the principal stress change from point to point within a beam?
A: Given: A beam is loaded. Explanation: Consider a beam which is loaded at a point shown below:
Q: Write different types of stresses that a material can be subjected to? (
A: There are different types of stresses depending upon the direction and their distribution. The…
Q: When an elastic material is subjected to normal stress, what would thestrains that are produced…
A: The strain is the response of a system to applied stress. When a material is loaded with a…
Q: ANSWER TO QUESTION 5.3.1 5.3.2) Ultimate tensile stress. ANSWER TO QUESTION 5.3.2
A:
Q: QUESTIONS 1. Define the terms load, stress and strain. Discuss the various types of stresses and…
A: We are suppose to solve only one question. Please post other question as a separate question.
Q: What is the magnitude of the shear stress due to torsion at the critical location?
A: Solution: The critical section is at A. The axial force G will produce Bending effect at A about…
Q: What is Normal Stress?
A: Normal Stress: When the stress is acting in the direction perpendicular to the body then it is said…
Q: what is the equation and units for finding yield stress?
A:
Q: between direct stress and bending stress.
A: To define: Distinguish between direct stress and bending stress
What is the general state of Stress?
Step by step
Solved in 2 steps with 1 images