Answered: What is the head loss in pipe due to…

What is the head loss in pipe due to friction over the length of 30 km, if the diameter of pipe is 80 cm and velocity of flow is 30 cm/s? Take friction factor 0.032.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter11: Temperature And Temperature- Related Variables In Engineering

Section: Chapter Questions

Problem 9P: Calculate the R-value for the following materials: a. 4 in. thick brick b. 10 cm thick brick c. 12...

See similar textbooks

Related questions

Q: H.W2 Determine the maximum deflection of the simply supported beam. E = 200 GPa and I = 39.9(10) m².…

Q: H In fig find the force of the water of the tank bottom, if H=2 m, width= 1.5 m and long (into the…

A: To find out the force of water of tank at bottom.

Q: , determine the magnitude F and direction 0 gnitude of 1400 lb.

Q: Points 1 2 3 4 5 6 B.S a d I.S b e f F.S c g H.I ارتفاع الجهاز 31.46 31.46 31.46 30.2 30.2 30.2 R.L…

A: Given values: Points B.S I.S F.S H.I R.L 1 a 31.46 29.3 2 b 31.46 28.9 3 d c…

Q: 2. A timber beam is reinforced with at the top and bottom as shown in Fig the moment increased by…

A: Given:- n=15 allowable stress in steel and wood=8MPa and 120MPa To find:- amount ofmoment increase

Q: Calculate horizontal deflection at point C in the following frame using unit load method. Take EI =…

A: ##Calculation of Horizontal Deflection of point C#### Using Unit Load Method###

Q: Determine the reactions for the shown structures. Question 1: 60 k/

Q: At the birth of a girl, what amount should her mother invest in order to provide the daughter with…

Q: Determine load P such that the axial stress in the steel pipe is 200 MPa P Imm GAP RIGIO PLATE

A: It is given that :

Q: you please write this on paper so I can easily understand it? It will be a great help thank you

Q: Using Mohr's Circle Determine: a.) The principal planes and directions b.) The principal Stresses…

Q: PROBLEM 1 A reinforced concrete beam has a width of 250mm and a total depth of 450mm. It is…

Q: Fluid flow with µ= 0.38 N.s/m2, P= 912 kg/m3, flows with velocity = 2 m/s through a pipe has 0.2 m…

Q: What will be polar moment of inertia of a solid circular shaft having a diameter of 150 mm? Select…

Q: If member AB elongates 10 mm as a result of the applied load as shown, determine the normal strain…

A: given:

Q: Problem 2: It is recommended to change the circular cross section shown in the figure by a square…

Q: Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction…

Q: Determine radius of mohr circle 9 MPa 4 MPa 6 MPa

A: Given data : The value of normal stress in X direction σX=-6 MPa The value of normal stress in Y…

Q: A 10 m 10 kN/m B Problem 2 a. Location of Amax from A b. Amax

A: Question is solved with double integration method. Since each method mentioned is different and…

Q: نقطة واحدة Control volume boundary 1-2- 2 200 mm diam Water v² Pz P₂ + 2g Y Which equation is true?…

Q: 9-57. Determine the principal stress, the maximum in-plane shear stress, an over 120 MPa D Z 300 MPa

Q: -12'- C H V 12'. G D 12'. TI F

Q: Problem Set #2 - FRICTION 6 cm MN Newton P=0.3 3 cm Required: 1. The minimum value of s if you…

Q: A concrete mix has a ratio os 1:2:4 by mass. The properties of the materials to be used are…

Q: the magnitude of the maximum shear stress in the compound shaft. (b) the rotation angle of flange C…

Q: hcp. IN fig. for FH, hcg= ---- =------? (The width =10 ft) ▼ Seawater y= 64 lb /ft³ B 11ft 6ft 6.375…

Q: P1 L1/2 W1 B -L1 P2 A SET (1) L1 3 m L2 4 m P1 5 KN -L2 P2 6 KN W1 7 KN/m W2 6 KN/m PROB 01 Support…

Q: 1. Determine the following: If w₁-5 kN/m and w₂ = 7 kN/m. Est = 210 GPa, b = 50 mm and h = 150 mm.…

A: Solution-

Q: nd the horizontal thrust

A: solution of above problem is below:

Q: 3. Determine the flow in pipe 3.

A: This question is from Fluid mechanics

Q: NAME: COURSE AND YEAR: GEOTECH 1 CE II-3A-F GEOTECHNICAL ENGINEERING 1 (SOIL MECHANICS) ASSIGNMENT 1…

A: Answer We know that gradation curve is plotted between the Grain size and % finer Grain size is…

Q: A small projectile is fired vertically downward into a fluid medium with an initial velocity of 60…

Q: 1. What is the difference between an excavation and a trench?

Q: The dimensions of a cylindrical core sample are 10.16 cm long and 3.81 cm in diameter after it was…

A: This question is related to the Soil Mechanics.

Q: aterials show superplastic behavior or are they always brittle? E

A: When stressed, a material is brittle if it splits with little elastic deformation and no…

Q: For a population of 2 lac having per capita daily demand of water of 150 litres, determine the water…

Q: 2 7 With reference to the following figure, the resultant force, F, forms an angle of a, measured…

Q: Find the force in Pin C. 6k 3¹ Bar JOK Bar EMB=C 34 S C B

Q: Find the Force in Pin C: A 10k 3' 5' C B 6k 3' 8'

Q: ween two points, A and B is [400+(1.79*10)]m, and these are established along the same direction…

A: Given:- A and B is [400+(1.79*10)]m To find:- The subtended angle read on a subtense bar held at A…

Q: In fig. the difference in pressure between the piezometer and pitot ?--- tube is

A: Solution-To Find The pressure differential (∆ P) between the piezometer & the pitot tube.…

Q: ff. The ordinates of is storm When divided by 6 giv hydrograph. When divided by 3 giv hydrograph.

Q: In an irrigated field, the net irrigation requirement is 15 cm, the application efficiency is 80%…

A: This question is from irrigation engineering Net irrigation requirement is equal to 15 CM…

Q: In fig. FV = Water ---- -? If the tank width is 5 m (into the paper) 4m 5m C 5m B 1941.6 N 1941600…

A: To find out the vertical force if the tank width is 5 m.

Q: Gage pressure is measured relative to the atmosphere, whereas absolute pressure is measured relative…

A: This statement is True

Q: A 120 kN 15 kN/m HIIIIc Į EIIII PAWANNACRO CONGO G B F D Hinge Hinge -8 m-5 m+5 m-5 m+5 m - 8 m - 10…

Q: in fig. FV=-----------? (gate width =8 ft) water weight density= 62.4 lb/ft3 Seawater y = 64 lb /ft³…

A: Given data in question Radius Depth Unit weight To find out Vertical force

Q: H.W2 Determine the maximum deflection of the simply supported beam. E = 200 GPa and I = 39.9(106)…

Q: A wall footing has a width of 1.4 m supporting a wall having a width of 0.24m. The thickness of the…

A: t (thickness of footing) = 0.44m d (width of wall) = 0.24m

Q: In an irrigated field, the net irrigation requirement is 15 cm, the application efficiency is 80%…

A: Given data- Net irrigation requirement NIR=15 cmapplication efficiency ηa=80%water conveyance…

Concept explainers

Pressure and Stress

Question

What is the head loss in pipe due to friction over
the length of 30 km, if the diameter of pipe is 80
cm and velocity of flow is 30 cm/s? Take friction
factor 0.032.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate the R-value for the following materials: a. 4 in. thick brick b. 10 cm thick brick c. 12 in. thick concrete slab d. 20 cm thick concrete slab e. 1 cm thick human fat layer
Water is flowing through a pipe that has a diameter of 18”, a friction factor of .03 and a length of 24’. Average water velocity is 15 ft/s. What is the friction head loss in the pipe?
On a rough surface, Daniel pushes a carton with a mass of 30.0kg. The force F that is he applies is 608N with an angle of 55.0 degrees with the horizontal. In a time of 4s, the block's speed increases from 0.15m/s to 2.68m/s. a) Draw a free body diagram for your calculations b) Find the coefficient of kinetic friction between the flood and the block.
A plunger (54 mm Ø and 0.5 m long) is moving through a horizontal cylinder (60 mm Ø) containing oil at a speed of 8 m/sec that has a viscosity of 7.1x10-6 m2/sec and specific gravity of 0.84. Calculate the force needed to maintain its velocity. Use 2 decimal places.
How high will the water jet reach, under the conditions shown in the figure? (WORK LIKE NEW PLEASE)
Determine the discharge in gallons per minute of water in a new 16 inch cast iron pipe if the frictional loss is 5 pounds per square inch per 1000 feet, Use Manning's equation with your own assumed value of roughness coefficient.
Two pipes, each 300m long 300 , are connected in series. The flow of water through the pipes is 150 L/s 0.15 with a total friction loss of 15m 15. If one pipe has a diameter of 300mm 0.3, what is the diameter of the other pipe? Neglect minor losses and assume f=0.02 0.02 for both pipes. Express your answers in 3 decimal places.
Determine the rate of flow of water through a pipe of diameter 10 cm and length 60 cm when one end of the pipe is connected to a tank and other end of the pipe is open to the atmosphere. The height of water in the tank from the centre of the pipe is 5 cm. Pipe is given as horizontal and value of f= 0.01. Consider minor losses.
Water floes through a circular pipe with a constant radius of 8cm. The speed and pressure at point a is 6 m/s and 300000 Pa respectively.a.) what is the speed of fluid at point b?b.) what is the pressure at point b which is higher than point a for about 5cm?
Water is flowing at a rate of 3ft/s through a pipe of diameter 1.5in and length 120ft. Determine the Reynolds number and the friction factor of the pipe. Take the value of kinematic viscosity of water as 1.052x10-5 ft2/s.
A 5 cm diameter horizontal jet of water with a velocity of 30 m/s strikes a flat plate that is moving in the same direction as the jet at a velocity of 10m/s. The water splatters in all directions in the plane of the plate. How much force does the water stream exert on the plate? What is the work done per second and the efficiency?
Water is flowing through a 2 inch diameter pipe at a velocity of 4.3 ft/s. If the length of the pipe is 100 ft, determine the Reynolds number. The value of kinematic viscosity of water is 1.21W10-5 ft2/s. Also calculate the friction factor.