What is the maximum moment Mmax that may be applied at the left support if the allowable shear stress in the glued joint is 200 psi? (Include the effects of the beam's own weight, assuming that the wood weighs 35 ft ) Round your answer to one decimal place. Mmax = kip ft Repeat part (a) if Mmax is based on allowable bending stress of 2500 psi. Round your answer to two decimal places. Mmax = kip ft

What is the maximum moment Mmax that may be applied at the left support if the allowable shear stress in the glued joint is 200 psi? (Include the effects of the beam's own weight, assuming that the wood weighs 35 ft ) Round your answer to one decimal place. Mmax = kip ft Repeat part (a) if Mmax is based on allowable bending stress of 2500 psi. Round your answer to two decimal places. Mmax = kip ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the vertical reaction at support A. Enter your answer in kN to two decimal places.
For this Problem, kindly refer to our Textbook, Structural Analysis Fourth Edition By Aslam Kassimali. For the given beam on Problem 5.8 Page 217, calculate the Moment in kip-foot at Point A if the given 40kip loads from the figure are both replaced by 68kips. Express your answer in 2 decimal places. Include (-) negative sign if the moment is negative.
For this Problem, kindly refer to our Textbook, Structural Analysis Fourth Edition By Aslam Kassimali. For the given beam on Problem 5.35 Page 220, calculate the Moment at B in kip-foot if the given 30kip concentrated load and 2kip/foot uniform load from the figure are both replaced by 23kips and 14kip/foot respectively. Express your answer in 2 decimal places. Include (-) negative sign if the moment is negative.
Replace the three forces acting on the guy wires by a single force acting on the flagpole. Use T1= 200 lb, T2= 400 lb, and T3= 350 lb.
Consider two blocks connected . BlockA has mass 2.00 kg, and block B has mass 5.00 kg. The table on whichB sits is frictionless, the cord connecting the blocks is light and flexible,and the pulley is light and frictionless. The horizontal force F S hasmagnitude F = 20.0 N, and block B moves to the left with an accelerationof 1.50 m/s2. What is the coefficient of kinetic friction that one block exerts on the other?
Calculate the moment at point B, for F1 = 5,000 lbs. F2 = 12,000 lbs. F3 = 8,660 lbs at α = 30° a = 4 ft, b = 3 ft, c = 2 ft, d = 1 ft
Using the Force Method of Analysis, draw the influence line for shear at point C of the beam shown. Plot numerical values every 5 ft. Assume the support at point B is a roller. EI is constant. Express your answers in 4 decimal places.
A beam rests on a fulcrum, 1.4 meters from one end. A weight of 495 kg is suspended from this end causing the beam to balance. If the weight of 495 is suspended on the opposite end of the beam, it is necessary to suspend a 2795 kg weight on the first end in order to effect an even balance. Use g = 9.81 m/s2. Find the length of the beam.
The following two questions refer to the beam below and the following values: w1 = 0.5, w2 = 0.1, l = 25, and a = 8. Give numerical answers to one decimal place. a. What is the negative moment at the roller (absolute value)?b. What is the moment at the point of maximum moment in Fig. 18 of the NDS moment diagrams (the value of moment at this point is marked "M1")? Give your answer with the correct algebraic sign.
The figure below shows the reinforced concrete beam AB of a tourist lookout at the free end. Its weight per unit length is 2500N/m, and the beam rests on two pillars at A and B, with no fixed connection. A. Assuming the beam is uniform, which of the following gives the absolute maximum shear? i. 12500N ii. 10000N iii. 7500N iv. 22500N B. What is the value of the absolute maximum moment? i. 31250Nm ii. 20000Nm iii. 11250Nm iv. 22500Nm C. Reinforcing steel bars [shown by the bold lines] are used in the concrete beam in the lookout as shown in the diagram below, which of the following diagrams best shows the placements of these reinforcements? Why?
Let G = 100kg, calculate the unknown loads A and B in order for the whole mechanism to stay stationary
Find the force in member BD.A 40 lb ladder 12 ft long leans against the wall making an angle of 30° with the wall. When a 180 lb man reached a point 8 ft from the lower end, the ladder is about to slip. Calculate the coefficient of friction between the ladder and the floor. The coefficient of friction between the ladder and the wall is 0.20