Answered: What is the maximum shear stress…

What is the maximum shear stress RESULTING FROM THE COMBINATION OF THE FOLLOWING stresses: Tesile stresses of SX-200 MPA, SY-100 MPA AND SHEAR STRESS of Ss=50 MPa?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.7P: The normal and shear stresses acting on element A are 6500 psi, 17,300 psi, and 2900 psi (see the...

See similar textbooks

Related questions

Q: What are the equation used for part a)? for the axial stress, why do we not use Axial Stress =…

Q: 6o vam 14 A GJVENI G =386 MDa T25KN-m `M=13KN-M D r-풍(물)+, J= 폭(을 Q1. DRAW STRESS STATES AT A IN X-Y…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: 2. Assume the plane stress state: ơ1 = 50, 02 = -250, T12 = 150 (all stresses in MPa). 2.1. Sketch…

A: σ1=50MPa σ2=-250MPa τ12=150MPa To Find Mohr's Circle Principal stress and their direction Maximum…

Q: Midrange and alternating stresses becomes equal only for Reversed stress O Repeated stress None of…

A: Option B Repeated Stress

Q: A circular shaft is subjected to combined loads of bending M and torque T. With the help of Mohr's…

A: Circular shaft is subjected to combined loads of bending M and torque TNow,Bending stress induced in…

Q: On the surface of a structural member, stresses are given as ox=67,9 MPa, oy=25,5 MPa and Ty=-24,3…

Q: 2) Find the axial stresses of members FD, GD, GE. State if it is tensile or Compressive. E 3m 5o kN…

A: Consider horizontally forward & vertically upward reaction as (+)ve and horizontally backward…

Q: Find the minimum principal stress for the stress case given in the figure.

Q: ural tensile stress in the bea stress at a section I m from section. ural compression stress in t…

Q: n a plane stress condition, the components of stress at a point are sigma_{x}= 20MPa , sigma_{y} =…

A: Given:σx=20 MPaσy=80 MPaτxy=40 MPa

Q: A body is subjected to a direct tensile stress of 300 MPa in one plane accompanied by a simple shear…

A: given data tensile stress = 300 MPa simple shear = 200 MPa to determine maximum shear stress

Q: The shaft of a hand operated wire rope hoist is supported on bearings A and B. The shaft is keyed to…

Q: A state of stress at a point A is given by ox = 50 MPa, oy = -25 MPa, and txy = -100 MPa. What is…

A: Please see the below explanation;

Q: 8. 10 plate 8X10 - S00 pounds of loud material 6061 Aluminum - Determine what type of stress Is…

A: Hf

Q: Find the maximum shear stress for the stress case given in the figure.

A: Given Data The stress acting in x direction is: σx=100 MPa The stress acting in y direction is:…

Q: If the principle stresses in a plane stress problem are 100 MPa and 40 MPa, then maximum shear…

A: As given in the question, Maximum principal stress = σ1 = 100 MPa Minimum principal stress = σ2 = 40…

Q: A steel cylinder is 160 mm ID and 320 mm OD. If it is subject to an internal pressure of 150 MPa,…

A: Given data Internal diameter of steel cylinder (Di) = 160 mm internal radius (ri) = 80 mm outer…

Q: Lical planes at the polnt are Sx (a) Determine the principal stresses (o,l > Op2) and the maximum…

Q: 7 Principal stresses of a point in a critical section of a machine component are: ₁= 80 MPa 0₂= 5…

Q: The vertical load P acting on the wheel of a traveling crane is 13,000 lb. What is the average shear…

Q: Problem 1: For each of the plane stress states listed below, draw a Mohr's circle diagram properly…

A: Given values of stresses acting on an element to draw mohr's circle and find the principal stresses…

Q: Angle 1 Oy Tyx Figure 1 Point A(-x-direction stress 60MPA(compression), y-direction stress…

A: The given values are - σx = -60MPa , σy = 40MPa, τxy = -30MPaθ = 30° The stresses on inclined plane…

Q: The thrust bearing supports a load P = 275KN. Find a. The tensile stress in the rod b. The shearing…

Q: The 12 kN.m torque is applied to the free end of the 5-m steel shaft. The angle of rotation of the…

Q: The position of the neutral axis; The maximum tensile and compressive stresses; and The shear stress…

A: Neutral axis is located at the centroi

Q: Consider a point in a structural member that vertical planes at the point are S, =26 MPa, S,= 19…

Q: Column is manufactured using concrete (E=4.2×10^3 ksi) and reinforcement is done by A-36 steel rods…

Q: Part 1 A steel pipe with an outside diameter of 115 mm and an inside diameter of 105 mm supports the…

A: Part 1As per given dataPx=Fx=-20kNPy=Fy=-16kNPz=Fz=-11kNPart 2Mx=16510-11230Mx=5630 kN.mmMx=5.63…

Q: 2. The drum of a steam generating units is 200mm in diameter. The steam pressure is 3.601325MPA. if…

A: Calculated the circumferential stress and the longitudinal stress.

Q: 4. For an element subjected to stresses of x= 70 ksi y=-15 ksi xy=30 ksi SAH: (a) Draw Mohr's…

Q: In the Figure 5, the normal stress on the cross- sectional area is (in Mpa): Figure 5: y P = 400 KN…

A: Area = A = 20 X 30 = 600 mm2 Force normal to area Pn = 400 cos (30) Pn = 346.41 KN

Q: Q1/ (A) - The mechanism of femur bone is approximated as a circular tube (3 cm and 2 cm are the…

Q: A state of stress at a point A is given by ax = 29 MPa, oy =- 195 MPa, and txy = -3.751 Which of the…

A: Data given- σx = 29 MPa σy = 195 MPa τxy = -3.75 MPa

Q: 4. For a [90/0] laminate given the a, stress profile below, determine: a) N. (k/in) b) M. (k*in/in)…

A: Stress is characterized as the obstruction force acting per unit cross-segment region of the body.…

Q: 1. Determine the shear, tensile and bearing stresses for the structural connection shown in Fig. 1.…

Q: M13.6 Principal stresses from rosette data scenes Ea -200 με %3D Eb = 200 με Ec 500 με 30° 30° Ex…

A: Given: “Since you have posted a question with multiple sub-parts, we will solve first three…

Q: The state of plane-stress at a point is given by σx = -200 MPa, σy = 100 MPa and txy = 100 MPa The…

A: Data given- σx = -200 MPa, σy = 100 MPa txy = 100 MPa

Q: Oy nd Txy 30 M -40 MF as n in Figure Q3. sider only the in-plane stresses. Note: the radius of the 2…

Q: 120 mm- The thrust bearing supports a load P = 275KN. Find a. The tensile stress in the rod b. The…

Q: Figure 1.1 shows a thick cylinder with inside radius of r;=94 mm and outside radius ro =136 mm was…

Q: Fill in the blanks. Draw and label the Mohr’s circle. For sigma-yp = 30 kSf. does this fail? Find…

Q: Próblem 1-19. A mild steel hollow shaft of 100 mm external di- ameter and 40 mm internal diameter is…

A: Answer: The direct stress, which acting alone, would produce the same (a) maximum elastic strain…

Q: 1) ) The curve of stress versus time on the cross section of engine connecting rod is shown in the…

Q: De ter mia the tensile and Compresnu stress for the bea shown in fig 160 lo wlm 2. m 20 mm 120 I =…

Q: -1 Figure Q-1, below, shows Mohr’s circle for a point in a physical object that is subjected to…

A: Given: 1 grid square = 3 MPa

Q: Determine the equivalent state of stress on an element at the same point onented 30°…

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

What is the maximum shear stress
RESULTING FROM THE
COMBINATION OF THE FOLLOWING
stresses: Tesile stresses of
SX-200 MPA, SY-100 MPA AND SHEAR STRESS
of Ss=50 MPa?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer diameter of 4.5 in. and thickness of O.OS in. Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses (out-of-plane and in-plane) at the outer surface of the tank.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial stress and is subjected to stresses a = -48 MPa and ay = 19 MPa, as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at a counterclockwise angle ?? = 25° from the x axis. (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
A simply supported beam is subjected to point load P at mid-span. The normal stress on an element at mid-span is known to be ??x= 1.5 ksi. Determine the element stresses lilt is rotated through angle ? = 450• Show these stresses on a sketch of an element oriented at that angle.
The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial .is in the and is subjected to stresses a, = 6250 psi and a. = -1750 psi, as shown in the figure. Using Mohr s circle, determine the following: (a) The stresses acting on an element oriented at a counterclockwise angle ? = 550 from the x axis. (b) The maximum shear stresses and associated norm al stresses. Show all results on sketches of properly oriented elements.
A prismatic bar with a length L = 3 ft and cross-sectional area A = 8 in2 is compressed by an axial centroidal load P = 10 kips. Determine the complete state of stress acting on an inclined section pq that is cut through the bar at an angle W = 35", and show the stresses on a properly oriented stress element.
The stresses acting on a stress element on the arm of a power excavator (see figure) are ax= 52 MPa and txy= 33 MPa (sec figure). What is the allowable range of values for the stress if the maximum shear stress is limited to = 37 MPa?