A cylindrical pressure vessel having a radius r = 14 in. and wall thickness t = 0.625 in. is subjected to internalpressure p = 375 psi. In addition, a torque T = 90 kip-ft acts at each end of the cylinder (see figure). (Assume that thestructures behave linearly elastically and that the stresses caused by two or more loads may be superimposed to obtain theresultant stresses acting at a point. Consider both in-plane and out-of-plane shear stresses unless otherwise specified.)TT(a) Determine the maximum tensile stress o,and the maximum in-plane shear stress Tin the wall of the cylinder.maxmax(Enter the magnitudes in ksi.)ksi=Tmaxksi(b) If the allowable in-plane shear stress is 4.5 ksi, what is the maximum allowable torque T? (Enter the magnitude inkip-ft.)| kip-ft(c) If T = 150 kip-ft and allowable in-plane shear and allowable normal stresses are 4.5 ksi and 11.5 ksi, respectively,what is the minimum required wall thickness (in inches)?in.

Torque: - It is defined as the force by which an object rotate about an axis.

Answered: what is the minimum required wall…

Engineering

Civil Engineering

what is the minimum required wall thickness (in inches)?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: For the cantilever beam shown on the above figure, determine the following: with complete solution…

Q: Show abd determine the reactions for the beam shown using the moment distribution method. What is…

Q: Draw the s-t and a-graphs if s=0 when t=0. v (m/s) = 21 t (s)

A: step 1-

Q: PROBLEM: Determine the instantaneous deflection (dead load only, live load only, and dead + live…

A: From the given data;

Q: A simply supported wood beam is subjected to uniformly distributed load q. The width of the beam is…

A: Given beam is simply supported with uniform distributed loadLength of span, L=17ftWidth of beam,…

Q: Draw the influence line for the reaction at A. Find the positive maximum equivalent unit load for…

Q: Compute for the following: 1.area of A2,A3 and A4 2.Total volume using average end area method

A: Take use of end average method.

Q: SIT S. The results of two-drained tri-axial tests on a saturated clay are recorded as follows:…

Q: Plastic Limit: TEST NO. Wt. of Wet soil + container Wt. of Dry soil + container Wt. of container 1 2…

A: We will calculate water content for each case.

Q: What is the leading cause of fire the leading cause of fire?

A: Leading cause of fire means that fire occurs more often than other causes or in other words most…

Q: 22' E. Determine the true bea whose magnetic bearing is S E

Q: Draw the shear and moment diagram then identify the maximum shear and maximum moment.

Q: If a steel with a 33ksi yield strength is used for a cold-formed shape, what would be the…

Q: For the loading shown, use the double-integration method to determine (a) the equation of the…

A: ASKED: To determine the equation of the elastic curve for the given cantilever beam and calculate…

Q: Convert 833m^2 to hectares

A: 1 hectare = 10000 sq m 1 Sq m= 1/10000 hectares 833 Sq m= 833*(1/10000) hectares= 0.0833 hectares

Q: Tri-axial Test SIT Q. A consolidated drained tri-axial test was conducted on a normally consolidated…

Q: A CABLE OF UNIFORM THICKNESS HANGS BETWEEN TWO POINTS 120 M APART WITH ONE END 3M ABOVE THE OTHER .…

A: step 1-

Q: An infiltration capacity curve prepared for a catchment indicated an initial infiltration capacity…

Q: An 8-m simply supported beam carries a concentrated load of 40 kN at a distance of 3.25 m from the…

A: To find location of maximum deflection from left support

Q: A wet soil weighs 3000g. It has a moisture content of 10%. How much water should you add to this…

Q: Calculate the maximum shear stress o, in the web of the T-beam shown in the figure if b = 14 in., t…

A: ASKED: To determine the maximum shear stress in the web of the T-beam section. Given, Shear…

Q: a 3" oj ob C" OC 5" of od 3" e = 4" A" B" | A" B" A" B" The holes are for 1-inch-diameter bolts.…

Q: eft end of the beam . maximum value of Ely . Ely value at midspan 2000 lb 4000 lb ft B. 8 ft Fig.…

Q: A fire extinguisher tank is designed for an internal pressure of 986 psi. The tank has an outer…

Q: A column in the upper story of a building is subjected to a compressive load from the following…

A: Note : Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: A small river is in flood stage and you need to estimate the flow rate through it. The main channel…

A: Given, nchannel = 0.025 nfloodplain = 0.04

Q: shown carries a 50 kip-in torque. Calculate (a) the maximum shear stress and (b) the angle of twist…

Q: Compute the design moment strength of the beam section describedbelow if fy = 420 MPa, fc’ = 21…

Q: Draw the influence line for shear at C. Find the maximum positive equivalent unit load for Shear at…

Q: 5 The command area of a canal grows only one crop. i.e., wheat. The base period of wheat is 120 days…

Q: What is the present value of a stream of monthly payments of $500 each over 10 years, if the…

A: step 1-

Q: solve for centroid and moments of area about the x-axis and y-axis.

Q: What are the effects on the latitude and departure components of an ending point’s coordinates, when…

A: Equal Latitude and departure- Latitudes are the distances from the north of the south of the given…

Q: The jib crane shown in the figure is subjected to three coplanar forces. Replace this loading by an…

Q: What does the term "pattern" signify in architecture? How may these three distinct architectural…

A: The approach of collecting architectural design concepts as iconic and repeatable representations is…

Q: A scuba tank is being designed for an internal pressure of 2,655 psi with a factor of safety of 2.0…

A: We will take maximum value of thickness.

Q: SIT H. A 300 mm diameter well penetrates 27 m below the static water table. After 24 hours of…

A: The diameter of pumping well, d=300mmThe depth of well, H=27mThe discharge rate, Q=96LsThe radial…

Q: For the cantilever steel beam [E = 190 GPa; I = 128 x 106 mm ), use the double-integration method to…

A: To find deflection at A

Q: 28 in. Problem #4 The A36 column base plate has thickness t= 1.5 inch and supports 935 20 kips, N =…

A: Column bases are structural elements, which transmit the load to the concrete or masonry foundation…

Q: 45 is used as a beam with lihes can be assumed to resist tension of the of L mm diameter boplts in…

A: Given: W10X45 section, A36 steel 18mm dia bolts, Fy=219 MPa, Fu=311.9 MPa A=8581 mm2 Dia of hole…

Q: eflection VA at point A. eflection vc at point C. O ft, LBc=5 ft, Lco =5 ft, LDE=5 ft.

Q: The perpendicular offset distance from point A on a simple curve tto Q on the tangent line is 64 m.…

Q: Problem 4: Determine LRFD flexural capacity (OMa) for a W21x73 used as a beam with an unbraced…

A: flexural capacity : The flexural capacity of concrete beams, according to this concept, is the sum…

Q: AW 12 x 35 steel cantilever beam is subjected to an axial load P = 9.5 kips and a transverse loadv =…

Q: 6) Determine the vertical displacement of joint A. AE is constant. Take A= 2 in and E-29 (10) for…

A: In case of truss calculation of vertical displacement due to loading can be calculated by using…

Q: 49. Well A has a piezometer reading of hi and Well B has a piezometer reading of h2. If h2 > hi: a.…

A: Solution (49) Well A has a piezoelectric reading H1 Which will be less than the well B has a…

Q: Draw the shear and moment diagram thenidentify the maximum shear and maximum moment.

A: To draw SFD and BMD

Q: Calculate the maximum shear stress omay in the web of the T-beam shown in the figure if b = 12 in.,…

Q: A very rough circular open channel has a diameter of 60 in and the depth of flow is 15.0 in. The…

Q: how far would you have walked (in miles)?

Question

A cylindrical pressure vessel having a radius r = 14 in. and wall thickness t = 0.625 in. is subjected to internal
pressure p = 375 psi. In addition, a torque T = 90 kip-ft acts at each end of the cylinder (see figure). (Assume that the
structures behave linearly elastically and that the stresses caused by two or more loads may be superimposed to obtain the
resultant stresses acting at a point. Consider both in-plane and out-of-plane shear stresses unless otherwise specified.)
T
T
(a) Determine the maximum tensile stress o,
and the maximum in-plane shear stress T
in the wall of the cylinder.
max
max
(Enter the magnitudes in ksi.)
ksi
=
Tmax
ksi
(b) If the allowable in-plane shear stress is 4.5 ksi, what is the maximum allowable torque T? (Enter the magnitude in
kip-ft.)
| kip-ft
(c) If T = 150 kip-ft and allowable in-plane shear and allowable normal stresses are 4.5 ksi and 11.5 ksi, respectively,
what is the minimum required wall thickness (in inches)?
in.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Vertical load is applied to point B of a 10 mm radius cylindrical bar as shown in the figure. Calculate the normal stress at point D.
Vertical load is applied to point B of a 10 mm radius cylindrical bar as shown in the figure. Calculate the shear stress occurring at point D.
A beam ABC with a cantilever from B to C supports a uniform load of 3 kN/m over its entire length (see figure). The beam is a gutter with the dimensions shown in the figure. The moment of inertia about the z axis (the neutral axis) is equal to 210 cm⁴ . Calculate the maximum stress in tension σt and the maximum stress in compression σc due to uniform loading.
A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 426 mm2 . Determine the average axial stress in each bar.
In the figure shown, determine the diameter of the rod C if the allowable stress 86.60 MPa. Neglect the weight of the bar AB.
1. In The given figure, calculate A. The resultant force at joint C in KN B. The resultant force at joint A C. The stress at Rod BC if it has an area of 150mm x 150mm.
Statics and Strength of Materials Topic: Bending Stress and Deflection Question:A rectangular tube has an outside width of 100 mm, an outside depth of 150 mm, and a wall thickness of 10 mm. If the bending moment is 1.4 kN.m, determine (a) the maximum bending stress in the tube in the MPa unit, and (b) the bending stress 10 mm from the top of the tube. Show all step-by-step solutions.Plot the bending stress in a graph showing tension and compression and clearly label the graph.
A closed cylindrical tank, placed horizontally, 400 mm in internal diameter and 2.2 mm thick is subjected to an axial compressive force (along its longitudinal axis) and uniform internal pressure. The stresses acting on an element of side is shown in the figure.a. What is the magnitude of the internal pressure in MPa?b. What is the applied axial force in kN? (detailed solution please)
A closed cylindrical tank, placed horizontally, 410 mm in internal diameter and 2.0 mm thick is subjected to an axial compressive force (along its longitudinal axis) and uniform internal pressure. The stresses acting on an element of side is shown in the figure.a. What is the magnitude of the internal pressure in MPa? b. What is the applied axial force in kN?
A bar with a cross section of 2320 mm2 P = 180 kN carrying pressure force Rod length L = 50 cm and Modulus of Elasticity, E = 140 GPa Calculate the normal stress that will occur in the rod andFind the changed height
The internal shear force at a certain section of a steel beam is V = 8.1 kN. The beam cross-section shown in the figure has dimensions of b=137 mm, c=33 mm, d=66 mm, and t=7 mm. Determine: the shear stress at point H. [Answer: 7.43 MPa]
The system shown in the figure has an acceleration of 0.5 m / s^2. Kinetic friction between blocks and surface that the coefficients are the same for both inclined planes accepting that a) the kinetic coefficient of friction b) in the rope find the stress