What is the need of compensation in power system? b) Give the schematic diagram showing a shunt compensator on a distribution transformer. c) Give the desirable characteristic features f a shunt compensator. d) List different methods used in shunt compensator. e) Name two power factor correction method. f) Define Facts and name 2 series connected facts devices g Draw a circuit diagram of a Static Synchronous Series Compensator (SSSC) and gives his applications.

What is the need of compensation in power system? b) Give the schematic diagram showing a shunt compensator on a distribution transformer. c) Give the desirable characteristic features f a shunt compensator. d) List different methods used in shunt compensator. e) Name two power factor correction method. f) Define Facts and name 2 series connected facts devices g Draw a circuit diagram of a Static Synchronous Series Compensator (SSSC) and gives his applications.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.55P: A single-phase l0-kVA,2300/230-volt,60-Hz two-winding distribution transformer is connected as an...

See similar textbooks

Related questions

Q: Question 2 By using source transformation technique, find Vo and the power delivered by the…

A: we need to determine the voltage Vo and power delivered by the dependent voltage source using source…

Q: 1. On a lossless 500 coaxial transmission line with a shorted load: a. a voltage minimum will occur…

A: The given problem is from transmission lines. The detailed solution is given in the next step

Q: For the block diagram in the attached pdf. 1 Find e when R(s) = SS Let K = 2. 2 — and D(s)=0.

Q: A Long Shunt Compound DC Generator supplies 90-amp at 120-volt. Series field resistance of 0.03-ohm,…

A: In this question We need to determine the efficiency of the generator. We know Efficiency= output…

Q: Assuming that the line is uniformly transposed. (a) Determine the transmission line inductance per…

A: Given: ACSR bundled conductor Distance between the conductor in a bundle = 30 cm the radius of…

Q: a) A 20-2 resistor is connected in series with an unknown resistor to a 200V Supply mains. If the…

A: Given data, Supply voltage V = 200 V. Current drawn i = 4 A. One of the resistance R1=20 Ω. Let…

Q: the circuit below: a). Find Vc0-), Vc(0+), and Vcfinfinity) b). For t> 0, calculate the time…

Q: 1. 1 What will the charge q₂ need to be if a charge q = 4.8 x 10 C is situated 6.0 cm to the right…

Q: A Y- connected, 10-KVA, 230- has a field winding resistance of 4.59. At an operation of 0.85 lagging…

A: Given data KVA rating, S=10 KVA Field winding resistance, rf=4.59 Ω Power factor, cosϕ=0.85 lagging…

Q: A unity feedback system has the open loop transfer function shown below. Find the angle of arrival…

Q: find the outer and inner diameter measurements of a three-phase 4-pole axial intelligent motor with…

A: Given information about a three-phase 4-pole axial intelligent motor is written below. Rated output…

Q: 14. For the network of Fig. 6.78, V₁ = 9 V. Determine: (a) ID- (b) Vs and Vps- (c) VG and VGS. (d)…

A: We need to find out the current and voltage for given circuit.

Q: 200pF, CD=CGD+CDB Consider the common gate amplifier shown below. Let R₁ = 2.5kN, Rs = 25kN, R₁ =…

Q: § 6.3 Self-Bias Configuration 10. For the network of Fig. 6.75, determine: (a) ID. (b) VDs. (c) VD-…

A: We need to find out the current and voltage for given circuit.

Q: A mass-spring-dashpot system with external force f(t) is described by the following differential…

A: The Mass spring dashpot is given as Md2xtdt2+Cdxtdt+Kxt=f(t),for M=1, C=0 & K=36, above equation…

Q: In the circuit shown below, calculate: vin Vos VOD MI M2 HOUT

Q: Design a three ip amp instrumentation amplifier having gain 20.

A: Instrumentation amplifier This amplifier works the same as a regular amplifier just to amplify the…

Q: ssume F from part 1 and add d(x,w,x,y,z) = ∑(3,7,10) then write the simplified e

A: Given: the boolean function F(w,x,y,z)= ∑(4,5,11,13,15) and d(x,w,x,y,z) = ∑(3,7,10) Draw K-map…

Q: The dual-slope ADC converts analog to digital information by a combination of integration and time…

A: A dual slope ADC produces an equivalent digital output for a corresponding analog input by using two…

Q: A parallel resonant circuit has an inductor of 100mH inductance and a capacitor of 10pF capacitance.…

A: Q-factor= Resonant frequency/BW BW= Bandwidth

Q: (b) The construction of Wheatstone Bridge used for measuring temperature is as shown in Figure…

Q: If in a communication system BPSK, QPSK, QASK-8 are used for transmission and reception of digital…

Q: Design a DC Power Supply Circuit with fix output (+5V & 3.3V) and variable output from (0 to 15V -…

A: a) The Block diagram regulated the power supply circuit The electronic design above shows four…

Q: = 200pF, CD=CGD+CDB Consider the common gate amplifier shown below. Let R₁ = 2.5kN, Rs = 25kN, R₁ =…

Q: a) Design a voltage to frequency converter using the 9400 as shown in the circuit below for fo=…

A: According to the question, for the given circuit of the voltage to frequency converter by using the…

Q: A plane wave at 1 GHz is normally incident on a thin copper sheet of thickness t. (a) Compute the…

A: Given data, Frequency ω=1×109 Hz Loss =150 dB

Q: Problem 6 Find the values for R, and X, that result in maximum power transfer if X, cannot exceed a…

A: Note: Only active power will be available in purely R Load Only Reactive power will be available in…

Q: lo vd1 1₂ ******* 1. With the figure above derive the value of vd-vd1. Answer:

Q: In ADC, sampling can be done in any rate or frequency as long as the hold mechanism is constant. O…

A: The sampling theorem defined as the minimum sampling rate at which a continuous time signal needs to…

Q: Example 7: A 220V shunt motor delivers 40Hp on full load at 950RPM and has an efficiency of 88%. The…

Q: § 6.2 Fixed-Bias Configuration 3. Given the measured value of V, in Fig. 6.69, determine: (a) ID.…

A: We need to find out the current and voltage for given circuit.

Q: § 6.3 Self-Bias Configuration 11. Find Vs for the network of Fig. 6.76. 14V 22kQ www Loss = 6 MA Vp…

Q: 4. Find the transient charge in an RLC series circuit when: L = 1H C = 0.25F R = 2Ω…

A: 4. Given, RLC series circuit is having L = 1H C = 0.25F R = 2Ω E(t) = 50 cos(t), V We need to find…

Q: how are GPS systems connected to solar cells

A: We have to explain how GPS systems are connected to solar cells?

Q: 12 and 13?

A: Given the circuit diagram R1=4 kΩ R2=7.5 kΩ R3=12.5 kΩ V1=35 V I1 is coming current at node V…

Q: Find the Inverse Laplace Transform of the following functions 1 Ans. f(t)=1-e¹ S + S 1 S³ + 4s 1)…

Q: #v + oto To S[t=0) 22 Fig 3 22 1F - Ис

Q: 1. A time-domain quantity is given as x(r)-5sin(3r+15). The phasor of this quantity is: (a) X-Se-A…

A: Given data, Function is given as xt=5sin3t+150.

Q: What is the angle of ignition in each thyristor? АС B EAB + EBC IL ECA İb + EL b R jab R T₁ ibc T3…

Q: 5. How do you calculate the Numerical aperture of an Optic fiber and what are the different types of…

A: Given: How to calculate the numerical aperture of an Optical fiber and explain the different types…

Q: An electrical engineering student assigned to perform an experiment about a dc generator but forgot…

Q: Sensors used to detect metallic parts only: O pH Sensor O Capacitive sensor O Thermocouple sensor O…

A: Sensor: Sensor is an electronic device. Sensor produce an output signal after sensing the physical…

Q: Example 2: A 220V shunt motor runs at 800rpm and takes an armature current of 50A. find the…

Q: 8. Determine the value of 1₁ and 12 in the network. 220/0° V I₁ 10 52. 3:1 лее = ell 22 ww

Q: How much power is emitted when not using the adjusting circuit and e) How much power is emitted…

Q: Problem-2: Consider the Laplace transform 2s + 3 X(s) = a) Find the zeros and poles of X(S). b) Find…

Q: Question 4 a) This question is about the Karhunen-Loeve Transform (KLT) i) The Karhunen-Loeve…

A: a) i) Karhunen-Loève transform also known as the Hotelling transform or the method of principle…

Q: The total current passed by a 10 Kilo ohms, a 15 Kilo ohms and a 20 Kilo ohms resistor in parallel…

Q: In the CDMA system the receiver receive the information from the channel and need not to regenerate…

A: A finite radio frequency must be divided up using CDMA in order for several users to access it…

Q: Generate a plot for the skin depth ds versus frequency for air for the range from 1 kHz to 10 GHz…

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

Question 1.

a) What is the need of compensation in power system?

b) Give the schematic diagram showing a shunt compensator on a distribution transformer.

c) Give the desirable characteristic features f a shunt compensator.

d) List different methods used in shunt compensator.

e) Name two power factor correction method.

f) Define Facts and name 2 series connected facts devices

g Draw a circuit diagram of a Static Synchronous Series Compensator (SSSC) and gives his

applications.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step by step

Solved in 7 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power input of 65 kW and a current of 30 A. Compute the values for GcandBm in siemens referred to the high-voltage winding. Compute the efficiency of the transformer for a load of 10 MW at 0.8 p.f. lagging at rated voltage.
Consider Figure 3.4. For an ideal phase-shifting transformer, the imda nce is unchanged when it is referred from one side to the other. (a) True (b) False
A single-phase two-winding transformer rated 90MVA,80/120kV is to be connected as an autotransformer rated 80/200kV. Assume that the transformer is ideal. (a) Draw a schematic diagram of the ideal transformer connected as an autotransformer. showing the voltages, currents, and dot notation for polarity. (b) Determine the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the rated values as a two-winding transformer. How much of the kA rating is transferred by magnetic induction?
Three single-phase, two-winding transformers, each rated 450MVA,20kV/288.7kV, with leakage reactance Xeq=0.10perunit, are connected to form a three-phase bank. The high-voltage windings are connected in Y with a solidly grounded neutral. Draw the per-unit equivalent circuit if the low-voltage windings are connected (a) in with American standard phase shift or (b) in Y with an open neutral. Use the transformer ratings as base quantities. Winding resistances and exciting current are neglected.
A single-phase l0-kVA,2300/230-volt,60-Hz two-winding distribution transformer is connected as an autotransformer to step up the voltage from 2300 to 2530 volts (a) Draw a schematic diagram of this arrangement, showing all voltages and currents when delivering full load at rated voltage. (b) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the rated values as a two-winding transformer. How much of this kVA rating is transformed by magnetic induction? (C) The following data are obtained from tests carried out on the transformer when it is connected as a two-winding transformer: Open-circuit test with the low-voltage terminals excited: Applied voltage =230V, input current =0.45A, input power =70W. Short-circuit test with the high-voltage terminals excited: Applied voltage =120, input current =4.5A, input power =240W. Based on the data, compute the efficiency of the autotransformer corresponding to full load, rated voltage, and 0.8 power factor lagging. Comment on why the efficiency is higher as an autotransformer than as a two-winding transformer.
A single-phase 100-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down transformer. The load, which is connected to the 240-volt secondary winding, absorbs 60 kVA at 0.8 power factor lagging and is at 230 volts. Assuming an ideal transformer, calculate the following: (a) primary voltage, (b) load impedance, (c) load impedance referred to the primary, and (d) the real and reactive power supplied to the primary winding.
Why is it important to reduce the moisture within a transformer to acceptable levels during transformer installation?
Three single-phase two-winding transformers, each rated 3kVA,220/110volts,60Hz, with a 0.10 per-unit leakage reactance, are connected as a three-phase extended autotransformer bank, as shown in Figure 3.36(c). The low-voltage winding has a 110 volt rating. (a) Draw the positive-sequence phasor diagram and show that the high-voltage winding has a 479.5 volt rating. (b) A three-phase load connected to the low-voltage terminals absorbs 6 kW at 110 volts and at 0.8 power factor lagging. Draw the per-unit impedance diagram and calculate the voltage and current at the high-voltage terminals. Assume positive-sequence operation.
For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
An ideal transformer has no real or reactive power loss. (a) True (b) False
A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
In developing per-unit circuits of systems such as the one shown in Figure 3.10. when moving across a transformer, the voltage base is changed in proportion to the transformer voltage ratings. (a) True (b) False