What is the potential difference ( in volts) across C2 when C = 5.0 µF, C2 = 15 µF, C3 = 30 µF, and Vo = 19.9 V?Vo

Given: The capacitance of capacitors are, C1=5.0 μFC2=15 μFC3=30 μF E.M.F. of battery Vo=19.9 volt

Answered: What is the potential difference ( in…

Science

Physics

What is the potential difference ( in volts) across C2 when C, = 5.0 µF, C2 = 15 uF, C3 = 30 µF, and Vo = 19.9 V? Vo

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter8: Capacitance

Section: Chapter Questions

Problem 31P: A 4.00-pF is connected in series with an 8.00-pF capacitor and a 400-V potential difference is...

See similar textbooks

Related questions

Q: Two capacitors when connected in parallel give an equivalent capacitance of 9.00 pF and an…

A: Let the capacitance of each capacitor be C1 and C2. When connected in parallel , Cp = C1 + C2 = 9 pF…

Q: Find the charge q(t) on the capacitor and the current i(t) in the given LRC-series circuit. L = h, R…

A: Given: L=5/3 H, R=10 ohms. C= 1/30 F , E(t) =600 volts initial charge and current =0

Q: In the figure below, take R1 = 260 Q, R2 = 180 Q, and R3 = 68 Q. A potential %3D difference of 9.0 V…

Q: C1= 6.0μF C2= 3.0μF Vab = 18V What is the equivalent capacitance, the charge and potential…

Q: The dielectric constants of SiO2, Si3N4, and Ta2Os, are about 3.9, 7.6, and 25, respectively. What…

Q: In the figure below, what is the potential difference V-V.between points d and cif &1=4.7 V, 82= 1.5…

A: Assume Vb=0. Then Vc=1.5, Va=4.7 In the right wire, Vd-i2R2=1.5 ---(1) In left wire 4.7-i1R1=Vd…

Q: The figure shows an open switch, a battery of potential difference V, a current-measuring meter A,…

Q: Assume that a cylindrical capacitor has diameter 5.0 cm and length 10.0 cm. Its capacitance is C =…

A: Given : d = 5 cm = 0.05 m r = d/2 = 0.05/2 = 0.025 m L = 10 cm = 0.10 m C = 2000 F Vmax = 2.9 V

Q: 3. What is the capacistance in the network if two capacitors 2 μF and 4 μF are connected series? A.…

A: Capacitance is defined as the ratio of charge divided by the potential difference applied across it.…

Q: Two fully charged capacitors are in series across a 50V source. If the first one is a 1 micro Farad…

Q: Q5) For a piezoceramic shown in figure, given that d33 = 500 *10(-12) m/V, capacitance C= 10*10 F,…

Q: Two capacitors of capacitance C1 = 100 nF and C2 = 5 μF are connected in parallel across a cell with…

Q: What is the equivalent capacitance for the following three capacitors connected in series: C1 = 100…

Q: Show that (ab)c can have more values than abc. As examples compare(a) [(−i)2+i]2−i and…

A: (a) [(−i)2+i]2−i and (−i)(2+i)(2−i) = (−i)5;(b) (ii)i and i−1

Q: Two capacitors C1 = 1 µF and C2 = 4 µF are %3D connected in parallel and charged to V = 3V. What is…

Q: The length of a copper cable is 255 km. The radius of the copper cable is r= 3.25 cm. The potential…

Q: AC = 16 µF capacitor has a potential deference of %3D 5000V. What is the energy stored in the…

A: Ans:- Image-1

Q: Problem 2: For the image shown, the capacitors have the following values: C1 = 2.95*10^-6, C2 =…

A: Given, Total capacitance, C = 5.94×10-6 F Potential (V) = 81 V

Q: Two capacitors of capacitance C1 = 100 nF and C2 = 5 μF are connected in series across a cell with…

A: The capacitance of the two capacitors: C1 = 100 nF (100 x 10-9 F) and C2 = 5 μF (5 x 10-6 F) The…

Q: In a circuit powered by 9V source, the series combination of 5.0 F and 20.0 F capacitors is…

A: Given, a circuit powered by 9V source, the series combination of 5.0 F and 20.0 F capacitors is…

Q: Two capacitors C1 = 1.5µF and C2 = 2.5µF are connected in parallel. If the combined charge 0n both…

A: Given:- Two capacitors C1 = 1.5µF and C2 = 2.5µF are connected in parallel. The total charge of…

Q: The voltmeters in the figure measure RMS voltages. If V1 = 13 V and V2 = 8.5V what is V3? R ww ele V…

A: Net voltage across the RLC in a series combination circuit is given by :…

Q: The cell membranes of axons, which which are nerve cells in the human body, act as very small…

A: The capacitance C is the ratio of the amount of charge Q stored in the capacitor to the potential…

Q: Three capacitors are connected in series. C1 = 3.3 microF C2 = 6.8 microF %3D C3 = 5.6 microF…

Q: capacitors and a voltage source are connected in series, as shown. Let C1=4.05pF, let C2=9.75pF, and…

A: Given C1 = 4.05 pF = 4.05 × 10-12 F C2 = 9.75 pF = 9.75 × 10-12 F Battery voltage Vo = 250 V

Q: From the figure below, if V =120V, find the potential difference across the capacitor 60pF. 104 40µ…

A: Given: The potential difference across terminal a and b , Vab =120 V To determine potential…

Q: . Follow the instruction and derive the formula given. a.)Using the definition C = Q/V, show that…

Q: A capacitor is fully charged to 24 V and then connected between points A and B in the figure,with…

Q: C3 C1 = 6.00 µF, C2 = 1.00 pµF, C3 = 3.00 pF, C4 = 6.00 µF, C4 Vas = 12.0V |C Figure 1. Network of…

Q: Consider the circuit shown. Let ε=16.0 Vε=16.0 V and let R1=R2=R3=R4=6.00ΩR1=R2=R3=R4=6.00Ω. What is…

A: The net resistance of the three resistors R2 , R3 , R4 connected in parallel is 1Rnet = 16+16+16 =…

Q: K, and a generator of voltage V. Mark as true or false the following statements concerning the stor…

A: We have to mark true or false for the given statements concerning the realtive phase of V, VL, Vr,…

Q: Two capacitors C1 = 2 nF, and C2 = 4 nF are connected in series to a 10V battery. The two capacitors…

A: Data given , C1 = 2 nF = 2 × 10-9 F [ 1 nF = 10-9 F ] C2 = 4 nF = 4 × 10-9 F C1 and C2 are…

Q: In the following diagram, C, = 6.00 pLF, C2 = 12 µF and C3=2 µF %3D Cz If we apply 60 V across a and…

A: Given: C1=6 μF, C2=12 μF, C3=2 μF. The voltage across a-b is Va-b=60 V.

Q: Given three capacitors, C1= 2microF, C2= 1.5microF and C3= 3.0microF what arrangement or parallel…

Q: its A capacitor discharges through a 820k2 resistor and drops to original voltage in 7 min How many…

Q: In an ECG, if the potential between the Right and left arm leads is 0.8 mV, and the potential…

Q: C1= 6.0μF C2= 3.0μF Vab = 18V What is the equivalent capacitance, the charge and potential…

A: Data Given , C1 = 6 μF C2 = 3 μF Vab = 18 V Let , charge on capacitor C1 is = Q1 Charge on…

Q: What is the potential difference ( in volts) across C2 when C1 = 5.0 µF, C2 = 15 µF, C3 = 30 µF, and…

A: Qeq= equivalent charge Ceq= equivalent capacitance Veq= equivalent potential difference Step 1)…

Q: (II) A neuron is stimulated with an electric pulse. The actionpotential is detected at a point 3.70…

Q: Three capacitors of 2, 3 and 6 µF, are connected in series, to a 10 V source. The charge on the 3 µF…

A: Given data: The capacitors are, C1=2 μFC2=3 μFC3=6 μF The voltage across the capacitor is V=10 V.

Q: Three capacitors, with capacitances C = 4.0 µF, C, = 3.0 µF, and C3 = 2.0 µF, are connected to a 12…

Q: A 100 pF, 100 kV concentric spherical capacitor with gas insulation with dielectric constant Ɛ=8,854…

A: Here given a 100 pF ,100 kV concentric spherical capacitor with gas insulation of dielectric…

Q: Four capacitors C, = C2 = 30µF, and C3 = C4 = 15µF are connected to a battery of voltage V = 24 V,…

A: Given: The capacitance of the capacitors C1, and C2 is 30 μF. The capacitance of the capacitors C3,…

Q: 3. Capacitors Ci=3µF, C2=2µF, C3=6µF and C4= unknown is connected in series with a 24 V battery. If…

A: Given- C=12μF ,C1=3μF, C2 =2μF, C3=6μF (a) For capacitance at C4- 1C=1C1…

Question

What is the potential difference ( in volts) across C2 when C = 5.0 µF, C2 = 15 µF, C3 = 30 µF, and Vo = 19.9 V?
Vo

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

Figure 21.55 shows how a bleeder resistor is used to discharge a capacitor after an electronic device is shut off allowing a person to work on the electronics with less risk of shock, (a) What is the time constant? (b) How long will it take to reduce the voltage on the capacitor to 0.250% (5% of 5%) of its full value once discharge begins? (c) If the capacitor is charged to a voltage V0through a 100-O resistance, calculate the time it takes to rise to 0.865V0(This is about two time constants.)
A circuit contains a D-cell battery, a switch, a 20- resistor, and three 20-mF capacitors. The capacitors are connected in parallel, and the parallel connection of capacitors are connected in series with the switch, the resistor and the battery, (a) What is die equivalent capacitance of the circuit? (b) What is the KC time constant? (c) How long before the current decreases to 50% of the initial value once the switch is closed?
The circuit shown in Figure P28.78 is set up in the laboratory to measure an unknown capacitance C in series with a resistance R = 10.0 M powered by a battery whose emf is 6.19 V. The data given in the table are the measured voltages across the capacitor as a function of lime, where t = 0 represents the instant at which the switch is thrown to position b. (a) Construct a graph of In (/v) versus I and perform a linear least-squares fit to the data, (b) From the slope of your graph, obtain a value for the time constant of the circuit and a value for the capacitance. v(V) t(s) In (/v) 6.19 0 5.56 4.87 4.93 11.1 4.34 19.4 3.72 30.8 3.09 46.6 2.47 67.3 1.83 102.2
(a) What is the average power output of a heart defibrillator that dissipates 400 J of energy in 10.0 ms? (b) Considering the high-power output, why doesn’t the defibrillator produce serious bums?
A homemade capacitor is constructed of 2 sheets of aluminum foil with an area of 2.00 square meters, separated by paper, 0.05 mm thick, of the same area and a dielectric constant of 3.7. The homemade capacitor is connected in series with a 100,00- resistor, a switch, and a 6.00-V voltage source, (a) What is the RC time constant of the circuit? (b) What is the initial current through the circuit, when the switch is closed? (c) How long does it take the current to reach one third of its initial value?
A student makes a homemade resistor from a graphite pencil 5.00 cm long, where the graphite is 0.05 mm indiameter. The resistivity of the graphite is =1.38102/m . The homemade resistor is place inseries with a switch, a 10.00-mF capacitor and a 0.50-V power source, (a) What is the BC time constant of the circuit? (b) What is the potential drop across the pencil 1.00 s after the switch is closed?
Suppose you need to measure the potential difference between the points in Figure P29.4. Assume the voltmeter reading is the potential difference between the two leads: V = Vred Vblack. For each of the following measurements, determine at which point you would connect the red lead and at which point you would connect the black lead: a. Vb Va. b. Vc Vb. c. Vd Vc. d. Va Vd. FIGURE P29.4 Problems 4, 5, and 6.
Figure P18.26 shows a voltage divider, a circuit used to obtain a desired voltage Vout from a source voltage . Determine the required value of R2 if = 5.00 V, Vout = 1.50 V and R1 = 1.00 103 (Hint: Use Kirchhoff's loop rule, substituting Vout = IR2, to find the current. Then solve Ohms law for R2. Figure P18.26
(a) Determine the equilibrium charge on the capacitor in the circuit of Figure P27.46 as a function of R. (b) Evaluate the charge when R = 10.0 . (c) Can the charge on the capacitor be zero? If so, for what value of R? (d) What is the maximum possible magnitude of the charge on the capacitor? For what value of R is it achieved? (c) Is it experimentally meaningful to take R = ? Explain your answer. If so, what charge magnitude does it imply? Figure P27.46
Figure P18.26 shows a voltage divider, a circuit used to obtain a desired voltage Vout from a source voltage . Determine the required value of R2 if = 5.00 V, Vout = 1.50 V and R1 = 1.00 103 (Hint: Use Kirchhoff's loop rule, substituting Vout = IR2, to find the current. Then solve Ohms law for R2. Figure P18.26
The temperature near the center of the Sun is thought to be 15 million degrees Celsius ( 1.5107oC ) (or kelvin). Through what voltage must a singly charged ion be accelerated to have the same energy as the average kinetic energy of ions at this temperature?
Two conducting wires A and B of the same length and radius are connected across the same potential difference. Conductor A has twice the resistivity of conductor B. What is the ratio of the power delivered to A to the power delivered to B? (a) 2 (b) 2 (c) 1 (d) 12 (e)12