Answered: What is the relation between reactance,…

Engineering

Electrical Engineering

What is the relation between reactance, resistance and impedance? O a. a. R-X O b. R+jX R+X O d. Rj + X

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter23: Resistive-inductive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ

See similar textbooks

Related questions

Q: 1. In the following figure: R = 3 kN X; = 2 kN Xc = 1 kN %3D + VC + VR VL e = 6 sin(314t + 60°)

Q: what is the z transform of (1/4)^k

Q: Tdeal diodes Dz 1-5kr 3. 9. Determine Vo (-) ayde. For (+) and Vi Vo b. Draw Vo. 2.sv+ + 1av

A: This question is belong to clippers and clamper diode circuits. Analysis is to be done with differen...

Q: To minimize the time where the voltage produced by a coil in the armature of a dc generator is zero,...

Q: For the ladder network in Fig. 2.104, find I and Reg. ww 15 V (+ 352 Rea

Q: When in its "on" state, the voltage across a Zener diode, Vz O increases sharply with a decrease in ...

A: When in its 'ON' state, the voltage across Zenger diode is....

Q: Electromagnets are utilized as key components of transformers in power supplies that convert electri...

A: Televisions Computers Cars Motors Water pumps MRI machines Relays Speakers Microphones

Q: The 110 W light bulb in Fig. 2.122 is rated at 110 volts. Calculate the value of V, to make the ligh...

Q: certain system given x(t) h(t) v(t) Cnowing that h(t) given by and x(t) given by use convolution 1- ...

Q: b) Briefly describe the function of an encoder. You may use a 4 to 2 decoder to explain the function...

Q: 1. Given the following circuit, determine: (a) Varms, The secondary peak voltage. (b)min Isave, The ...

A: Since you have asked multiple questions in a single request, we will be answering only the first thr...

Q: resistance of each of the given resistor. Use the samples presented in the discussion part as your g...

A: With this table , it is possible to answer only the ideal resistance value so i will answer that onl...

Q: Three resistors A, B, and C are connected in series to a 117-volt source. If RA = 64 ohms, and Vg = ...

Q: In the circuit in Fig. 2.76, obtain vi, V2, and v3. +20 v - - 60 V + 40 V - + v2 - + 40 V V3

Q: what are the Factors that aFfec? Value of ele ctrical Resi stance? R-2) Find the value of the Follow...

A: Factors affecting value of electrical resistance are- Temperature Cross-section area Wire length Na...

Q: inductor has an inductance of 3H. It is connected in series with a resistance of 1Ω. It is fed from ...

A: We need to find out the time constant for given circuit

Q: Qu. 3 For the circuit shown in Fig. 3, answer the following: a) What is the relationship between Vi ...

A: In this question one converter is given....We have to find out it's type and will write relationship...

Q: explain in detail and type the solution

A: An Electric Drive is responsible for various controls of an electrical motor or generator. It majorl...

Q: x[n] =[ 1 1 1 ] and x[n] =[ 1 3 5 ] a. b. What does the arrow in the previous question mean? c. x[n]...

Q: Find the equivalent resistance Rab in the circuit of Fig. 2.111. 42 8Ω 10 Ω WWo a d Loa 3Ω f

Q: A 3-phase 3-wire, 415 V supplies a balanced load of 20 A at power factor 0.8 lngging. Two wattmeters...

A: The solution is given below

Q: Solve for Vec, Veb, Ic, and identify the region of operation and explain why. Beta=200

A: In this question, We need to determine the voltage Vec, Veb, and current Ic, and identify the regio...

Q: Consider a trinary communication channel [STAR 1979] whose channel diagram is shown in Figure 1.P.6....

A: Taking Ti as transmission and Ri is reciever, and i=1, 2, 3 Thus, we have, T1, T2, and T3R1, R2, and...

Q: mplify the block diagram shown in following figure and obtain the closed-loop ansfer function C(s)/R...

A: The given block diagram can be reduced by considering the parallel connected and cascade connected b...

Q: A signal r(t) is band limited to 5kHz: it is sampled at a very high rate of 100kHz using ideal sampl...

Q: Exercise 1) Determine the voltage of 2 resistor in the network below using superposition method. 2Ω ...

Q: Derive the Fourier Series expansion of ) given 4-Vpp, 1MHZ square wave signal shown in Figure 2.1. b...

Q: 2. Draw the power flow diagram. Indicate the line losses. Using 100MVA Base, solve for Voltage at Bu...

A: The Power flow diagram represents the losses of the motor. The inward and outward can also the expla...

Q: H.W. Compute the minimum bandwidth of transmission channel in KHz for eight band signal each 5KHZ if...

Q: Q1. Consider a message signal m(t) = 20 cos(2Ħt) and a carrier signal c(t)=50 cos (100 z t), both in...

A: Please find the detailed solution in below images

Q: 1. Compare between the normal and zener diodes. 2. What is the application of the zener diode?

A: Comparison between Normal Diode and Zener Diode Normal Diode Zener Diode 1. Only conducts in ...

Q: Write about the applications of electric fan

Q: The 110 W light bulb in Fig. 2.122 is rated at 110 volts. Calculate the value of V, to make the ligh...

Q: Repeat problem if RL = 470 Ohms Rs Determine: a. If the diode is "ON" b. IL, Is, Iz C. Pz 2202 Vi Vz...

A: Zener diode turns on when open circuit voltage across RL is greater than zener voltage Vz. Based on ...

Q: generation current density at a reverse bias

A: Semiconductor- Materials which don't have free electrons in valence so there is no flow of current ...

Q: etermine the maximum power that can be delivered to the load RL in the network n the figure below. 1...

Q: Vz ksz P2m :100mW)

Q: Perform transient circuit simulation for an RC (R=1k, C=1uF) circuit shown in Figure 12 to determine...

A: The solution is given below

Q: 1-) I 4+7 i solve the complex number 2.) 5+ 3i transform to rtan dard Form

Q: Ex. 316. Determine the closed-loop steady-state error given a R(s) + E(s) ->0----->| G(s) |---+---> ...

A: The solution is given below

Q: In the figure, what is the current supplied by the emf when the frequency is very small? Assume that...

Q: d (b) the power in each resistor.

Q: Find the current Iy in the 4-ohm resistor in the circuit in the figure. 12 V ww 2 A (1)Vx 2Vx

Q: Derive the mathematics of a circuit A series of 5 units of insulators Extract V5 in detail

Q: What is the phasor expression for the impedance in polar form for the circuit below? 56 N Xc 100 N O...

A: Given circuit:

Q: The zero-state scaled network shown in Figure 131 is driven by the sinusoidal voltage source Eg(t) e...

A: The current in the loop can be calculated by using mesh analysis after finding the impedance of the ...

Q: What will happen if the back emf drops to zero because the external mechanical load stops the armatu...

A: Back EMF is the generated when the motor is under running condition. If N=0, the back emf will also ...

Q: For R1=70, R2=70, R3=46, R4=64, R5=71, R6=49, R7=15, R8=37, R9=58 , R10=39 and 1=0.06 A in the circu...

Q: A1. Voltage sag is common power frequency disturbance that can last half of a cycle to several secon...

A: Voltage sag is an important consideration while analyzing the power quality. It is always recommende...

Q: What is the magnitude of the current in the 20 Q resistor? 102 10 V 20 2 15 V 10 N

A: Given circuit:

Concept explainers

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.

Question

What is the relation between reactance, resistance and
impedance?
O a.
a. R-X
O b. R+jX
R+X
O d. Rj + X

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
Consider the circuit shown in Figure 2.23 in time domain. Convert the entire circuit into phasor domain.
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
Inductive Circuits Fill in all the missing values. Refer to the following formulas: XL=2fLL=XL2ff=XL2L Inductance (H) Frequency (Hz) Inductive Reactance ( ) 1.2 60 0.085 213.628 1000 4712.389 0.65 600 3.6 678.584 25 411.459 0.5 60 0.85 6408.849 20 201.062 0.45 400 4.8 2412.743 1000 40.841
Given the following Resistances and Capacitors in Series and Voltage Source: R1 = 6.946 ohms R2 = 9 485 ohms C1 - 0.731 Farad C2 - 0.925 Farad Vs - 15 Volts Frequency = 168 Hz What is the Capacitive Reactance of C1?
Given the following Resistances and Capacitors in Series and Voltage Source: R1 = 9 ohms R2 = 3 ohms C1 - 0.008 Farad C2 = 0.003 Farad Vs = 2 Volts Frequency = 6 Hz What is the Total Reactance in ohms?
Reactances are connected in series: |XC1| = 100, |XC2| = 40, |XL1| = 30, |XL2| = 70. What is the net reactance? 140 40 100 20
Clear solutions pls. Thank you Given the following Resistances and Capacitors in Series and Voltage Source: R1 = 1 ohms R2 = 10 ohms C1 = 0.007 Farad C2 = 0.008 Farad Vs = 9 Volts Frequency = 6 Hz What is the Total Reactance in ohms?
Given the following Resistances and Capacitors in Series and Voltage Source: R1 - 7 ohms R2 = 4 ohms C1 = 0.157 Farad C2 = 0.01 Farad Vs = 10,382 Volts Frequency = 86 Hz What is the Amplitude of the voltage across C1?
An inductor of L = 500 mH and R = 100 ohms passes a current of i = 4sin(500t) A. What is the voltage across the element and the power factor of the circuit?
36 - Since a =5i ̂-2j ̂+3k ̂ and b =2i ̂-j ̂-3k ̂, what is the result of (a +b )? A) 4 B) -1 C) 4i ̂+3j ̂+2k ̂ D) 7i ̂-3j ̂ E) 3i ̂ + 2j ̂-3k ̂
a)For the inductive element of Figure 1 , the current in phasor form is B) the voltage in phasor form for figure 1 is C)the impedance of the inductor for figure 1 is