What will be displayed on the displays?

Q: 1. Are the theoretical calculations and measured values are equal? Explain?

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: this represents an OLTC system, taken from the matlab program, explain what the elements used are,…

A: A 25 kV distribution network consisting of three 30-km distribution feeders connected in parallel…

Q: Given the image below, what are the control signals needed to perform the NOT operation (OR (x, y)).

A: The control signal needed to perform the NOToperation (OR(x,y) ) are:Since,zx =1, then x = 0, the…

Q: Can you solve the question quickly please?

A:

Q: What is counter? What is its purpose?

A:

Q: ‏List the flags that would be affected during the use of IN instruction.

A: In this question we will know about the flags that would be affected during use of instruction....

Q: 1- Which type of instruction dose INTO normally follow? Which flag does is test?

A: The signals that are directly available from the devices are analog. Hence a conversion is required…

Q: Explain different types of ADC with figures?

A:

Q: Reduce the number of states in the following state table, and tabulate the reduced state table:

A: From table state 'd' and state 'h' are equal. Then replace everywhere h by d and h-state are reduces…

Q: What was the first electrical digital computer comprised of?

A: All latest  computers today are digital computers. An electronic digital computer uses electricity…

Q: The performance of a communication system can be affected by noise from both internal and external…

A:

Q: Multitasking is defined as the ability to do many tasks at the same time.

A: Mutitasking is the abilty to do many tasks at the same time It means shifting between tasks is done…

Q: What is the reason of "Hanged Display" and "Misplaced Display" in the LCD Display of mobile?

A: The reasons for the "Hanged Display" and "Misplaced Display" in the LCD Display of mobile could be…

Q: What is the difference between a task and a function in verilog?

A: As per our company guidelines we are supposed to answer only first one question. Kindly repost other…

Q: Briefly explain the operation of a counter controlled ADC

A:

Q: Explain the construction and operation of CRO with diagram.

A:

Q: The dynamic behavior of a system is manipulated and judged under the application of typical test…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: In which areas/fields can ICs be used?

A: Integrated circuit is abbreviated as IC These are also known as micro chips as they are very small…

Q: How equation is obtained ? is that equation given in the textbook ?

A: That equation is the direct formula of pulse spread. And no need of derivation of the equation.…

Q: What does a pictorial or component arrangement diagram show.

A: A pictorial diagram or a component arrangement diagram makes use of simple images of different…

Q: In what situation we cannot select both current and voltage references randomly? Why?

A:

Q: Difference between system task $monitor and $display? (In context of Verilog/System verilog)

A: Verilog is Hardware Description language . The memory and array declaration in Verilog is static in…

Q: What are the Rules in Performing Laboratory experiments in the Electrical Engineering Laboratory?…

A: It's vitally important to take safety precautions when working with electricity. Safety must not be…

Q: A proportional system of control system. How to disable OFF-SET ? Draw example for Process line…

A: The oscillations around the set point (known as oscillation) in some processes may be too severe to…

Q: How many times is a do while guaranteed to loop?

A: So the do while loops runs once and it is guaranteed.

Q: Communication system The question is : explain the occurrence of the white noise in the…

A: The occurrence of the white noise in the communication system is as follows: - In signal processing,…

Q: 4) What is the function of measurement system?

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: The term accuracy describes the maximum expected error associated with a measurement.true or false?

A:

Q: What does a compatible load mean? What if the load is not compatible?

A: This question is from "Power system and protection". Under which we are going to study load…

Q: To access the services of the operating system, the interface is provided by the

A: The correct option along with the explanation is provided in the following section.

Q: how do i go about graphing

A:

Q: What is the use of the LCD display?

A: Write the use of the LCD.

Q: How to find Vo? And how to calculate it?

A:

Q: Explain what is Grid system

A: The Grid system is a network to deliver electricity from producer to consumer.

Q: What is the voltage and maximum current that can be used on the three cable types to power DeviceNet…

A: DeviceNet DeviceNet is a network protocol used in the automation sector to connect and share data…

Q: 8) What are the applications of the instruments and measurement systems? 9) Why calibration of…

A: 8)• Used for Regulating Trade: The measurement instruments are used to measure quantities like…

Q: 3. With the help of a solar panel name plate, explain each and every parameter displayed in it in a…

A: Solution3 - Generally, a solar panel nameplate contains the following parameters - 1. Maximum…

Q: List the flags that would be affected during the use of IN instruction.

A: The IN instruction is a kind of mnemonic which is used for the input in microprocessor. It input the…

Q: Write the laws or rules used to calculate a PV array station and explain each rule?

A: For the selection of a PV power system the rules to be followed are: Determination of power…

Q: How will you identify the electronics devices status in the industry?

A: BJT and MOSFET are the class of transistors used in analog electronics. They are widely used…

Q: · Explain the meaning of terms (Accuracy and Precision) and give example for an each?

A: Accuracy:- Accuracy is defined as the "closeness" to the true value.So, an instrument is said to be…

Q: What is the name of the wires that connect the memory?

A: Memory: Memory serves as the computer's electrical storage facility for the instructions and data…

Q: Can you create a concept map using these information?

A: We need to draw the concept map by using the given information.

Q: what is the curret gain?

A: BJT (bipolar junction transistor)A transistor having a three terminal made up of semiconductor…

Q: Get the same shape required and Give proper label and title by using OCTAVE and write the program

A: Get the same shape required and Give proper label and title by using OCTAVE and write the program

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.