What would be the purpose of wiring two normally open start buttons in series rather than parallel?

Q: we are interested in an automatic garage gate system for a building. This system includes a gate…

A: Given information about an automatic garage gate system for a building is, this system includes a…

Q: What does the inlet air temperature sensor mean? Explain how to verify the integrity of the wires…

A: The Intake Air Temperature sensor (IAT) screens the temperature of the air entering the motor. The…

Q: Microwave Oven an open loop or closed loop system?

A: Open Loop System- A control system in which the input of the system does not depends on the output…

Q: When a push button is used for the function of start, how are the contacts generally wired?

A:

Q: Differences between zero current switching (ZCS) and zero voltage switching (ZVS)?

A:

Q: Explain what timer count means?

A: 8254 is a timer/counter device used to solve used to solve timing control problems in a…

Q: What will happen to the output (light) if you use the XIC instruction associated with a normally…

A: XIC instruction is associated with Programmable Logic Controllers (PLC) and used in ladder logic…

Q: Which type of MCB is used in motor control and why this type of MCB is chosen over other types?

A:

Q: Identify and describe the basic functional elements that may be used in closed-loop control for all…

A: (a) Electronic speed control mainly follows a speed reference signal to change the speed of a…

Q: Assume that timer TR1 is set for a delay of 10 seconds and timerTR2 is set for a delay of 5 seconds.…

A: 10 seconds

Q: Sub-Parts A,B and C, have been solved by a Bartleby expert earlier, and told me to post the question…

A: Solution (d)

Q: A washing machine is supplied with hot and cold water from two different supplies. Draw the bock the…

A: Given, Two inputs with cold and hot water supply. The flow of hot water as well as the cold water…

Q: Explain different types of ADC with figures?

A:

Q: or a jet pump which is larger the drive pipe or the suction pipe

A:

Q: Common selector switches are?

A: => Common selector switches, controls on and off of different current circuit by rotating the…

Q: Explain operation of a battery ignition system?

A:

Q: What are the two main types of limit switches?

A:

Q: What value should come to the cell indicated by A2 when the Routh table of the control system given…

A: Using the Characterstic equation for routh hurthwiz  Find A2 in given table?

Q: A single - break control is a?

A: A single- break control is a standard-duty selector switch.

Q: From what location are the first computer instruction ?available on boot up

A: using the bootup process one can make it ready to use by putting in the instructions which it needs…

Q: What is a limit switch?

A: According to the question we have to define limit switch.

Q: If two push buttons are wired both as a stop and each device needs equal control, how should they be…

A: A push-button is a type of switch. when the button is pressed, it completes the circuit. normally,…

Q: What are the advantage of automatic than manual change over switch?

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: Briefly explained the function of the hold device in a digital control system.

A: The hold device is used to convert discrete signal into continuous or analog signal which can be…

Q: Compare between indirect and direct control circuits.

A: Indirect control circuit : Cylinders with large piston diameter have a high air requirement. Control…

Q: What is the advantage Synchronizing Lamp compared to Synchrosope?

A: The brief working and advantages are as follows.

Q: Determine the input and output connections for an oven with automatic temperature regulation. Cite…

A: According to the question, we need to determine the input and output connections for an oven with…

Q: Why two-tone test signals are used for making PEP measurements?

A: 2-tone testing is a method of detecting intermodulation distortion in electrical components and…

Q: Explain the used of Drum Switches? Draw the 6 point , 8 point and 9 point drum switches?

A:

Q: c) List FOUR (4) main inputs to the Motor Driven Power Steering Control Module (MDPSCM) and explain…

A: A circuit board and wiring in an aluminium box aren't all that make up an electric power steering…

Q: normally open and normally close contacts cannot be close simultaneously?

A: Because their actions are complementary, one requires energy to close, and the other requires…

Q: f I were to fill in the table to have a robot follow a line being detected by the three sensors, how…

A:

Q: Can you explain why a stop button must be normally closed and a start button must be normally open?

A: ⇒The stop button is normally closed and the start button is normally open .⇒Because there is one…

Q: Draw an schematic control diagram of a reversing starter. Use a standard-duty selector switch with…

A: Find the control diagram of a horizontal reversing starter power circuit,

Q: Consider the block diagram shown is for a closed-loop temperature control system. Where is the…

A: Given: The block diagram for a closed loop temperature controlled system is,

Q: Question: Describe the functionality of the following buttons and LEDs on the front panel while…

A: An analog input or digital interface is used to remotely regulate the functioning of a programmable…

Q: the block diagram model for a computerized control system?

A:

Q: What is meant by normally open contacts and normally close contacts?

A: (1) A normal contact pair is open when it is in a de-energized state (i.e Non-conducting state).…

Q: Exercise-2: Design a PLC program and prepare a typical I/O connection diagram and ladder logic…

A: A programmable logic controller (PLC) or programmable controller is a ruggedized and modified…

Q: Aastion 19 Which of the following explanation is NOT true? Select one: O a. A measurement system is…

A: 20)  Mechatronic system consist of mechanical, electrical and control system. First controller is…

Q: Design a PLC program and prepare a typical I/O connection diagram and ladder logic program for the…

A: In the question, the following data is given. A motor named M and three controlling START/STOP…

Q: Explain the function of the common control block when used with the standard graphic symbols.

A: The control blocks are present in the PLC control system for added functionality in the system. The…

Q: Name 5 types of the control system for micro air vehicle

A: A new type of remotely controlled aircraft is known as a micro air vehicle (MAV) or micro aerial…

Q: Following error

A:

Q: What is the difference between a one function and a multifunction electronic control device

A: A one function electronic control device operate only one function, Those equipment which uses…

Q: Write the applications 5-5 each of toggle, push, limit, rotary, DIP, selector switch.

A: Toggle- Toggle switch are actuated lever angled in or two of more position. The common house-hold…

Single Phase Induction Motor

The single-phase induction motor or engine consists of a single rotating phase in the stator and a rotating cage in the rotor. When phase one supply is connected to the stator winding, a magnetic field is generated. In the pulsating field, the rotor does not rotate due to inertia. So, a single-phase import motor does not start and requires some initial methods.