What's wrong with this connection?

Q: What is this?

A: First picture ka response to a circuit diagram for a motor drive. The motor connected in the circuit…

Q: What is workshop

A: What is workshop?

Q: What is external setup?

A: EXTERNAL SETUP: Setup is the method involved with setting up a machine to run an item. A portion of…

Q: The insulation rating of class 3, PLTC, FPL, CM cables rated at ____ volts.

A: Ans. 300 volts

Q: Define the tunneling current.

A: A quantum mechanical phenomena known as tunneling. When electrons pass through a barrier that they…

Q: 7. Higher slopes are required in cases where there is a lot of mismatch between the CTs at various…

A: We have to explain: "Higher slopes are required in cases where there is a lot of mismatch between…

Q: 9.a. What should be done with the connector ferrule once a connector is attached to a fiber optic…

A:

Q: Define the term "local wide network."

A: The given terms are as follows -  1. Local Network 2. Wide Network

Q: Questions focussed on Channel 1. Coaxial cable and optical fibre are two highly engineered wire…

A: The difference between optical fiber and coaxial cable is shown below. BASIS FOR COMPARISON…

Q: Explain what is happening here? Don't know what it is?

A:

Q: This site is a failure. It rejects all questions and does not solve them in a timely manner

A: We are sorry for that.

Q: grounding

A: In this question, we have to write about grounding accomplishment..

Q: Give four reasons why electroanalytical methods with their advantage over other methods.

A:

Q: How are the male and female terminals removed and replaced in a multipin connector?

A: Electrical Connectors are very important in the electrical circuits which is used to make continuous…

Q: What is wrong with this circuit? *

A:

Q: For the circuit shown in the figure below, com

A:

Q: You have an underground buried cable, suppose the cable is defected (open circuit) somewhere along…

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: Please explain the concepts regarding the equivalent resistance of series, parallel, and…

A:

Q: With the aim of a schematic, explain the principle of high impedance busbar protection.

A: High impedance bus bar protection requires High impedance CT with high knee point voltage and the…

Q: Briefly describe how a distance can be measured by the method of phase comparison

A: From the method of phase comparison, the distance is measured indirectly by determining the number…

Q: IV) What is Cell Relay? Give applications.

A: As per Bartleby guidelines we are allowed to solve only one question,please ask the rest again. The…

Q: This one

A: For the given circuit I, VL, VT, IT, VL, VR is determined as shown below

Q: For a close loop system.

A:

Q: Consider a group of students that are sifting through a crate with broken or malfunctioning cables,…

A: Cable faults can be found by looking for Ethernet symbol errors on switch and router interfaces.…

Q: What's the maximum percent overshoot %OS for this system with its closed-loop poles as shown? jo 12

A:

Q: Discuss  Suspension insulators are recommended in high voltage transmission lines.

A: Pin encasings become excessively cumbersome an uneconomical past 33 kV. Thus, for voltages higher…

Q: This discussion relates to Bonding. Whys is bonding of the conduit necessary when using reducing…

A: Bonding becomes necessary to reduce the risk of shock and it also provides a low impedance path to…

Q: Identify the minimum distance requirements between network cables and power sources and identify…

A: 50 mm is the minimum distance required between the power source and network cables.

Q: What is the super tension cable and application,rating

A: In this question we are discussing about super tension cable and application,rating. This is…

Q: How would you draw the root locus for this system?

A: Control system is defined through the transfer function. The control system has to be stable for…

Q: What can be said about the stability of the system below?

A:

Q: find the following parameters for the arcust below

A:

Q: What is the UPS

A: A uninterruptible force supply (UPS) is a gadget that permits a PC to continue to run for in any…

Q: | True

A: Sequence Local that is we pass a value from one sequence to the next

Q: shunts and multiplier

A: Full-Scale deflection in voltmeter:- when a known voltage has appeared across it, this voltage will…

Q: What do you understand by the term phase containment of errors? Explain with example.

A: Specifications, architecture, implementation, integration, & deployment are the steps of an…

Q: what is a locus

A:

Q: What is the value of VR

A:

Q: What is the name and purpose of the following components of the Arduino board:

A: 1. Digital Pins There are 13 digital pins available in the Arduino. These pins will act like input…

Q: Discuss overhead and underground tranmission systems.

A: The name itself says Overhead means transmission from top, Underground means transmission from…

Q: What is mean by equipment grounding and system grounding? 2. Discuss any two types of grounding…

A: Grounding is provided for the equipment or system in order to protect the system from short circuit…

Q: Explain what is going on here?

A: the given circuit is,

Q: What is ampere circuital law?

A: This law gives the relation between the magnetic field and the current which created the magnetic…

Q: Explain what is going on?

A: It is given that:

Q: Which level(s) of measurement is(are) considered qualitative? * Ratio and Interval Interval and…

A:

Q: What is mean by equipment grounding and system grounding

A:

Q: 4.a. An intersystem bonding termination will typically be used as a ground junction for a/an A.…

A: Answer 4.(a) According to 214 NEC, Intersystem bonding method is only one bonding method permitted…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.