When implementing a network with WAN technologies, which of the following must be known? (select two) a. A modem is used to connect to a digital line. b. A router is typically considered a DTE device. c. A CSU/DSU is used to connect to an analog line. d. A router is typically considered a DCE device. e. A modem is used to connect to an analog line.

When implementing a network with WAN technologies, which of the following must be known? (select two) a. A modem is used to connect to a digital line. b. A router is typically considered a DTE device. c. A CSU/DSU is used to connect to an analog line. d. A router is typically considered a DCE device. e. A modem is used to connect to an analog line.

A+ Guide to Hardware (Standalone Book) (MindTap Course List)

9th Edition

ISBN:9781305266452

Author:Jean Andrews

Publisher:Jean Andrews

Chapter9: Supporting Network Hardware

Section: Chapter Questions

Problem 6RB

See similar textbooks

Similar questions

1. Name the advantages of optical fiber over twisted-pair and coaxial cable. 2. Compare and contrast (major points) between a circuit-switched network and a packet-switched network. 3. The two types of networks, datagram and virtual-circuit, need a routing or switching table to find the output port from which the information belonging to a destination should be sent out, but a circuit-switched network has no need for such a table. Give the reason for this difference. 4. What is the Hamming distance for each of the following codewords: a. d (10000, 00100)b. d (00101, 10000) 5. Find the minimum Hamming distance for the following…
62. Ethernet and Token-Ring are the two most commonly used network architectures in the world. Jim has heard of the different topologies for networks and wants to choose the architecture that will provide him with the most options. Which of the following would that be? Choose the most correct answer. a. Token-Ring, because it uses a MAU b. Ethernet, because it can be set up with most topologies and can use multiple transfer speeds c. Neither Token-Ring nor Ethernet is the proper choice. Only ARCnet can be used in all topologies d. Token-Ring because it currently can run at both 4Mbps and 16Mbps. This means that it can be used in any topology
Select the correct statement(s) regarding connectionless and connection-oriented networks. a. packet networks support either connection-oriented or connectionless circuits b. A connection must be established prior to exchanging data when using a connectionless circuit c. packets must contain source and destination addresses in a connection-oriented circuit d. all statements are correct
The acronym SDN stands for "software-defined networking," and it refers to a set of standards for digital transmission via conventional copper wire telephone lines, in addition to other forms of media.a. CCITT b. ITU c. A, B, and D, respectively. None of the aforementioned.None of the aforementioned
Discuss the role of VLAN membership modes, such as access and trunk ports, in a network switch's operation.
2. In the Ethernet packet, the "Data" part is used to contain data send from source to destination and vice versa. The minimum number of data bytes is 46; what if the data is less by 2 bytes
Computer Science A 10-Mb/s Classic Ethernet transmits data packets obtained from the Network Layer. Assume for simplicity that the obtained data packets are directly placed into the MAC Ethernet frame, i.e. that no extra bytes are added in the LLC sub-layer.
Design an Ethernet network to connect a single client PC to a single server. Both the client and the server will connect to their respective workgroup switches via UTP. Their workgroup switches are connected directly by a trunk link. The two switches are 900 meters apart. They need to communicate at 800 Mbps. Your design will specify the locations of any switches and the transmission link between the switches. Then add another client next to the first client. This client will also communicate with the server and will also need 800 Mbps in transmission speed. Again, your design will specify the locations of switches and the transmission link between the switches.
Refer the above diagram. Two PC’s are connected to a switch. The IP addresses of the PC’s are as displayed in the diagram. PC (192.168.1.2) is connected to port Fa0/1 on the switch and PC (192.168.1.3) is connected to port Fa0/2 on the switch. If PC1 requires to communicate with PC2, what is required from PC2. Is a router required for PC1 to communicate with PC2. In the above diagram, how many mac-addresses would be available in the mac-address table of the switch after PC1 communicates with PC2.
What is a leased line, and how does it differ from a dedicated circuit in a WAN?
Explain the concept of SD-WAN (Software-Defined WAN) and its advantages in modern networking.
From the IEEE Standard Notation, state the notation of each Ethernet System. For example, the notation 10Base-5 means 10-Mbps transmission rate, baseband mode of transmission, with a maximum segment length of 500 meters. Will give thumbs up after, thanks