Which circuit? Look at the 2 circuits below. Ia. In which circuit is the voltage the biggest? b. Explain why you have chosen that circuit. 2 a. In which circuit is the voltage the smallest? b. Explain why you have chosen that circuit. 3 a. In which circuit are the bulbs the brightest? b. Explain why you have chosen that circuit. 4 a. In which circuit is the current the biggest? b. Explain why you have chosen that circuit.

Which circuit? Look at the 2 circuits below. Ia. In which circuit is the voltage the biggest? b. Explain why you have chosen that circuit. 2 a. In which circuit is the voltage the smallest? b. Explain why you have chosen that circuit. 3 a. In which circuit are the bulbs the brightest? b. Explain why you have chosen that circuit. 4 a. In which circuit is the current the biggest? b. Explain why you have chosen that circuit.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter27: Service-entrance Equipment

Section: Chapter Questions

Problem 40R

See similar textbooks

Similar questions

20 cells with emf for each cell are 1.5V and internal resistance 0.3Ω is connected in parallel. Calculate the value of current flow if the external resistance, 7Ω is joined to them.
Part 1 After using the UT33B multimeter to check the voltage of the batteries and the resistance of, light bulb and resistors, these are the results: - Voltage of the battery is measured to be 1608 mV, The scale used to measure voltage is 2000mV on the UT33B multimeter - Resistance of the bulb is measured to be 0.24 ohm, The scale used to measure resistance is 200 ohm on the UT33B multimeter - Resistance of the resistor1 (R1) is measured to be 15.2 ohm, The scale used to measure resistance is 200 ohm on the UT33B multimeter - Resistance of the resistor2 (R2) is measured to be 27.2 ohm, The scale used to measure resistance is 200 ohm on the UT33B multimeter Part 2 After connecting a circuit to find the resistance of the light bulb and resistors experimentally using a circuit, these are the results: LIGHT BULB - Resistance of the light bulb and resistors could not be measured on the UT33B multimeter, so the voltage and current were measured and the resistance was found using ohms law.…
Assuming the batteries supply a potential difference of DeltaV = 3.0 V, and use Ohm's Law along with the total currents measured in circuits 4a, 4b and 4c to determine the equivalent resistance of each circuit. Please show the calculation of each.
1)Aluminum piping is permitted to be used as a grounding electrode only if other electrodes specified in 250.52(A) are not available for use. a) True b) False 2)The Code requires that more than one grounding electrode be installed to form a system of installed electrodes when none are present. a) True b) False
From the data collected in Tables 1,2, and 3, plot the current versus voltage characteristic for each table seperated. Make sure VDis the horizontal axis with IDon the vertical.
Determine how well the resistance of a resistor can be determined by the measurements of current (I) that passes through the resistor and voltage (V) across the resistor. 2-Design a circuit to measure a 2.2K resistor using volt- ampere method. 3-Discuss the main reason for the probable error occurred during experiment
The circuit diagram below is for a robot that walks around the room. It is designed to stop walking when certain conditions are met. a) In which of the following cases will the robot start walking? i. The robot is far from the wall. ii. The battery status is good. iii. The room lights are on. iv. Both i and ii. v. i, ii, and iii. vi. ii and iii, but not i. vii. i and iii, but not ii. b) Explain what happens to the robot if the light is turned off. ______________________________________________________________________________ ______________________________________________________________________________ c) If you remove the light sensor and the AND gate attached to it from the circuit from the circuit, which of the following are true and which are false? i. The robot will continue to walk with a low battery ii. The robot will stop walking if it is close to the wall iii. One of the remaining inputs (proximity sensor and battery status) is irrelevant to whether the robot walks or not.…
Eight lamps are always connected in parallel as shown in the Figure.(a) If the set is connected to a 120V source, what is the current through eachlamp whether each internal resistance of 1.8 kohm?(b) Determine the total resistance of the network.(c) Find out the power dissipated in each lamp.(d) If a light bulb burns out (ie opens the filament), what is the effect on theremaining lamps?(e) Compare the parallel arrangement of a figure with a series arrangement. what are the relativesadvantages and disadvantages of parallel system compared to series arrangement? or Oito lâmpadas sempre estão ligadas em paralelo como mostrado na Figura.(a) Se o conjunto está ligado a uma fonte de 120V, qual é a corrente através de cadalâmpada se cada uma resistência interna de 1,8 kohm?(b) Determinar a resistência total da rede.(c) Descubra a potência dissipada em cada lâmpada.(d) Se uma lâmpada queima fora (ou seja, abre o filamento), qual é o efeito sobre aslâmpadas restantes?(e) Compare o arranjo…
You are a journeyman electrician working in a large office building. The fluorescent lighting system is operated at 277 V. You have been instructed to replace the existing light ballasts with a new electronic type that is more efficient. The manufacturer of the ballast states that the maximum peak operating voltage for the ballast is 350 V. Will the new electronic ballast operate on the buildings lighting system without harm?
A 6V battery is connected to a 300 ohm load. Under these condition, if the battery is rated at 40 Ah, then how long will it be able to supply the current to the load?
Which of the following lamp that will produce a 57.33 lm/W luminous efficacy? a.A 60 W flourescent lamp (and 15 W ballast) that emits 4300 lm of light b.None of these c.A 75 W incandescent lamp that emits 4300 lm of light d.A 75 W flourescent lamp that emits 4300 lm of light e.A 40 W incandescent lamp that emits 505 lm of light
The EMF of the battery is 0.14 kV and its internal resistance is 1.2 Ω. It is connected to an external resistance of 0.10 kΩ by means of a lead wire of resistance 45?Ω. (a) Find the TPD of the battery. (b) What is the voltage across the external resistance?