Which is CORRECT about capacitive and inductive reactance? O a. Inductive reactance is directly proportional with inductance. O b. Both the inductive and capacitive reactance are directly proportional; with inductance and capacitance, respectively. O c. Both the inductive and capacitive reactance are inversely proportional; wth inductance and capacitance, respectively. O d. Capacitive reactance is directly proportional with capacitance.

Which is CORRECT about capacitive and inductive reactance? O a. Inductive reactance is directly proportional with inductance. O b. Both the inductive and capacitive reactance are directly proportional; with inductance and capacitance, respectively. O c. Both the inductive and capacitive reactance are inversely proportional; wth inductance and capacitance, respectively. O d. Capacitive reactance is directly proportional with capacitance.

Physics for Scientists and Engineers with Modern Physics

10th Edition

ISBN:9781337553292

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter32: Alternating-current Circuits

Section: Chapter Questions

Problem 34AP

See similar textbooks

Similar questions

An RLC series circuit has a 1.00 k(resistor, a 1.50 (H inductor, and a 25.0 nF capacitor. (a) Find the power factor at f = 7.50 Hz. (b) What is the phase angle at this frequency? (c) What is the average power at this frequency? (d) Find the average power at the circuit’s resonant frequency.
A 60.0- resistor is connected in series with a 30.0-F capacitor and a generator having a maximum voltage of 1.20 102 V and operating at 60.0 Hz. Find the (a) capacitive reactance of the circuit, (b) impedance of the circuit, and (c) maximum current in the circuit. (d) Does the voltage lead or lag the current? (e) How will putting an inductor in series with the existing capacitor and resistor affect the current? Explain.
An RLC series circuit has a 2.50 (resistor, a 100 (H inductor, and an 80.0 (F capacitor. (a) Find the power factor at f = 120 Hz. (b) What is the phase angle at 120 Hz? (c) What is the average power at 120 Hz? (d) Find the average power at the circuit's resonant frequency.
An RLC circuit consists of a 150- resistor, a 21.0-F capacitor, and a 466-mH inductor connected in series with a 120-V, 60.0-Hz power supply. (a) What is the phase angle between the current and the applied voltage? (b) Which reaches its maximum earlier, the current or the voltage?
An 80.0- resistor and a 200-mH inductor are connected in parallel across a 100-V (rms), 60.0-Hz source. (a) What is the rms current in the resistor? (b) By what angle does the total current lead or lag behind the voltage?
The lowest frequency in the FM radio band is 88.0 MHz. (a) What inductance is needed to produce this resonant frequency if it is connected to a 2.50 pF capacitor? (b) The capacitor is variable, to allow the resonant frequency to be adjusted to as high as 108 MHz. What must the capacitance be at this frequency?
When a wire carries an AC current with a known frequency, you can use a Rogowski coil to determine the amplitude Imax of the current without disconnecting the wire to shunt the current through a meter. The Rogowski coil, shown in Figure P30.8, simply clips around the wire. It consists of a toroidal conductor wrapped around a circular return cord. Let n represent the number of turns in the toroid per unit distance along it. Let A represent the cross-sectional area of the toroid. Let I(t) = Imax sin t represent the current to be measured. (a) Show that the amplitude of the emf induced in the Rogowski coil is Emax=0nAImax. (b) Explain why the wire carrying the unknown current need not be at the center of the Rogowski coil and why the coil will not respond to nearby currents that it does not enclose. Figure P30.8
A transformer may be used to provide maximum power transfer between two AC circuits that have different impedances Z1 and Z2. This process is called impedance matching. (a) Show that the ratio of turns N1/N2 for this transformer is N1N2=Z1Z2 (b) Suppose you want to use a transformer as an impedance-matching device between an audio amplifier that has an output impedance of 8.00 k and a speaker that has an input impedance of 8.00 . What should your N1/N2 ratio be?
Consider the Filter circuit shown in Figure P33.56. (a) Show that the ratio of the amplitude of the output voltage to that of the input voltage is to that of input voltage is VoutVin=1/CR2+(1C)2 (b) What value does this ratio approach as the frequency decreases toward zero? (c) What value does this ratio approach as the frequency increases without limit? (d) At what frequency is the ratio equal to one-half?