Which is not a cause of detonation? Wrong ignition timing Allowing the engine to overheat Fuel/air mixture too lean Using a fuel grade higher than recommended

Q: Q.3. The right-angle bar shown in figure (3) is supported by a pin at B and a roller at C. What is…

A:

Q: Question 4 The following table lists molecular weight data for a polytetrafluoroethylene material.…

A:

Q: Determine the distance "a" for which the largest absolute value of the bending moment of the beam is…

A: First calculate the reactions. Then draw the bending moment diagram

Q: VOR can be tuned from the following places in most large body aircraft. Nav control panel MCDU…

A: following is the answer to the above problem

Q: Problem 3: A hot rolled steel shaft is subjected to a torsional load that varies from 3000 in-lb…

A: Answer: The required diameter of the shaft is 1.2813 inch.

Q: A converging-diverging nozzle discharges air into a receiver where the static pressure is 1.034 105…

A: Introduction: A nozzle is a variable cross-sectional area tube used to increase the speed of an…

Q: A turbine of 9000 B.H.P. is working under a head of 25 m and runs at 100 R.P.M.- What will be the…

A:

Q: 1. Consider the translational mechanical network system shown on the figure. A 1-lb force, f(t), si…

A: Disclaimer:“Since you have asked multiple questions, we will solve the first question for you. If…

Q: A constant force of 512 N was done on an object. If it is known that 1024 Joules of energy was…

A: Given            Force, F = 512 N Work done, W = 1024 J Find   Distance, d

Q: Q3. The inclined beam is suffered by king eat (1) vollar alf). Dettimine the load at (land() and B…

A: Given: The load, P = 500 N

Q: What is the velocity as measured by an orifice plate (0.06-m diameter) in a 0.305-m-diameter pipe…

A:

Q: A spark-ignition engine has a compression ratio of 10:1. The total intake volume of the cylinders is…

A:

Q: For the following beams, draw the simplified free-body diagram and below it the shear and bending…

A: Given: Let us consider the given image and Calculate the bending moments at the places of zero shear…

Q: uring the rolling process, the average flow stress is 20,000 lb/in², etermining the amount of…

A: Given Data The average flow stress is:γf=20000 lb/in2 The strength coefficient is:K=35000 lb/in2…

Q: FCP graduate who joined the Navy as a pilot is about to take off in an F-15 (WF15 = 81,000 lb) from…

A: Introduction: The constant thrust is a type of mechanical force. It is most commonly produced by the…

Q: This instrument uses an onboard radio interrogator that communicates with a ground radar…

A:

Q: 1.1 Determine the shear and moment values at every load point. 1.2 Draw the shear and moment diagram…

A:

Q: A pipe line consist of 10 cm diameter for 105 meter and 7.2 cm for the next 68 m. Carries water at…

A: We know that a pipe line has a diameter of 10 cm for the first 105 metres and 7.2 cm for the last 68…

Q: Determine the largest end forces P that the member can support if the allowable stress is T = 100…

A:

Q: A refrigeration system has a heat rejected of 430 kw.If COP is 7,find the mass chilled water in the…

A: Given , T2-T1=16o COP=7, QR=430KW, Find  mw

Q: An SUV hauling a trailer is travelling at 25 m/s when the driver hits the brakes. The 1.4 MT trailer…

A: Given data Speed of SUV and trailer = 25 m/s Mass of trailer = 1.4 MT = 1.4 x 1000 kg Mass of SUV =…

Q: 4.23 A 900-mm strip of steel is bent into a full circle by two couples applied as shown. Determine…

A:

Q: What is truss

A: This question is based on the concept of trust in mechanical engineering.

Q: 01 A reciprocating compressor cómpresses 1 m³/min of gas from 1 bar to 5 bar. The clearance is 8%…

A:

Q: A Dynamics experiment consists of collar B (mg = 10 kg) traveling to the left at VB = 1.5 m/s on a…

A:

Q: An object that has a Gs = 0.95 is found floating on a certain liquid with Gs = 1.06. If the volume…

A:

Q: hii, what's the right formula for n? h2 will be subtracted in the numerator too as well as in the…

A: ◆ The correct formula for efficiency of ideal Rankine cycle is given by, Efficiency = (Turbine work…

Q: Air is drawn in a gas turbine unit at 15°C and 1.01 bar and pressure ratio is 7: 1. The compressor…

A: Given that, Temperature of air, T=17 °C,Pressure of air, P=1.01 bar,Pressure ratio, rp=8:1Isentropic…

Q: Determine the length of side C of the triangle shown in Figure 2. 30 m 65⁰ 45 m

A:

Q: Example 1 The bar is subjected to a moment of M = 17.5 N.m. If r = 5 mm, determine the maximum…

A: Introduction: Bending stress is the typical stress that an item experiences when subjected to a…

Q: For the given plane strain state, use Mohr's circle to determine the strain state associated with…

A: Write the given data. εx=-500εy=250γxy=120θ=-15°

Q: 3- The following rod rotates about AB axis. If the angular velocity and acceleration are…

A:

Q: The efficiencies of aircraft can be very important indicators for meeting emission standards. Often…

A: Given    Calorific value, LCV = 43.15 MJ/kg  Fuel consumption, s = 0.06 kg/hr          Mass of fuel,…

Q: Why do most materials exhibit an increase in dimensions when heated?

A: Thermal Expansion of material : When the material heated it gets expands is called as thermal…

Q: Hydrogen at 4°C is circulated at 1500 psi/min from the lower to the upper reservoir, as in Fig.…

A:

Q: Determine the velocity of the liquid at the exit, given that h1 = 1.5 m and h2 = 0.3m. 1691556 Mird…

A:

Q: 3. A reheat steam cycle has 13,580 kPa of throttle pressure at the turbine inlet and 37.50308414 atm…

A:

Q: In the position shown, the angular velocity and acceleration of the AB bar are wAB = 7.7 rad/s…

A:

Q: shielded metal arc welding operation is performed on steel at E= 30 volts and / = 225 amps. The heat…

A: Given             Voltage, E = 30 V              Current, I = 225 amps Melting energy, U = 10.2…

Q: A cone clutch with a cone angle of 12° transmits 53 kW at 1300 rpm. The coefficient of friction of…

A:

Q: What is mostly the hydrostatic force per unit width of the dam due to the water acting as shown.…

A: GivenH=3mw=1

Q: Determine how many kg ofnitrogen will the flask hold at

A: Given data; Pressure,P=16 barvolume of the flask=0.08m3Temperature,t=300C=30+273=303 K Find how many…

Q: Ex. For the system shown in the Fig bellow write equation of motoin and Find the naturad frequency?…

A:

Q: To view the complete problem, hover over the blue information symbol. The horizontal and vertical…

A:

Q: A wooden plank x meters long has one end leaning on top of a vertical wall 1.5 m long and the other…

A: Given Data The lenght of the vertical wall is:L=1.5m The force is:F=100 N The weight of block…

Q: 1. A Brayton gas cycle produces a net load of 600 Btu/lb for an entrance temperature of 40°F and…

A: Given data Cycle : Brayton Gas cycle Net Load = 600 BTU/lb  = 1395.60 kJ/kg Entrance temperature =…

Q: The capitalized cost of a piece of equipment was found to be 145,000. The rate of interest used in…

A:

Q: On a piston of 20 cm diameter force of 2000N is uniformly applied. Find pressure on the piston ?

A:

Q: Determine the height of an oil column of specific gravity 0.8 in 1) meter of Hg 2) in meter of oil…

A:

Q: Subject Thermodynamics For the question (check the image) I need: 1. Give the assumption(s)…

A:

Hermetic Compressors

A compressor is a device that is used to increase the pressure of gas from low pressure to high pressure. The compressor is like a control volume, where in and out of mass occurs along with the interaction of energy with the surroundings in the form of heat and electricity.