QN:1 Suppose that five strings pull one at a time on a horizontal beam that can pivot about a pin through its left end, which is the axis of rotation. Find the torque due to each forces T₁, T₂, T3, T4 and T5. (Each force is 200N and length of beam is /= 2m) Axis of rotation T 60° 1/2- T 2 60° 13 3 4 18 5 Is UT

QN:1 Suppose that five strings pull one at a time on a horizontal beam that can pivot about a pin through its left end, which is the axis of rotation. Find the torque due to each forces T₁, T₂, T3, T4 and T5. (Each force is 200N and length of beam is /= 2m) Axis of rotation T 60° 1/2- T 2 60° 13 3 4 18 5 Is UT

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter15: Oscillations

Section: Chapter Questions

Problem 40P: Reciprocating motion uses the rotation of a motor to produce linear motion up and down or back and...

See similar textbooks

Similar questions

An elevator cable winds on a drum of radius 75.6 cm that is connected to a motor. A) If the elevator moves down at 0.520 m/s, what is the angular speed of the drum? in rev B) If the elevator moves down at 0.520 m/s, what is the drum’s frequency of rotation? in Hz
A wheel of radius 30.0 is rotating at a rate of 3.10 revolutions every 0.0810 s. 1. Through what angle does the wheel rotate in 1.00 s? 2. What is the linear speed of a point on the wheel's rim? 3. What is the wheel's frequency of rotation?
URGENTTTTTTTTTTTTTTTTT If the man in B exerts a force of P = 30 lb on his rope, determine the magnitude of the force f that the man in C must exert to prevent the pole from rotating, that is, so that the moment resulting from both forces with respect to A is zero.
A car tire is 62.0 cm in diameter. The car is traveling at a speed of 16.0 m/s. What is the tire's rotation frequency, in rpmrpm? What is the speed of a point at the top edge of the tire? What is the speed of a point at the bottom edge of the tire?
Find 0(theta) and W in the figure below where w1 = 15.0 N, w2 = 31.0 N, and ? = 64.0°, assuming that the arrangement is at rest. 0(theta)= W =
You Rev your car's engine to 3300 rpm. What are the period and frequency of the engine? If you change the period of thr engine to 0.033s, how many rpms is it doing?
A nylon siring has mass 5.50 g and length L = 86.0 cm. The lower end is tied to the floor, and the upper end is tied to a small set of wheels through a slot in a track on which the wheels move (Fig. P18.76). The wheels have a mass that is negligible compared with that of the siring, and they roll without friction on the track so that the upper end of the string is essentially free. Figure P18.76 At equilibrium, the string is vertical and motionless. When it is carrying a small-amplilude wave, you may assume the string is always under uniform tension 1.30 N. (a) Find the speed of transverse waves on the siring, (b) The string's vibration possibilities are a set of standing-wave states, each with a node at the fixed bottom end and an antinode at the free top end. Find the node-antinode distances for each of the three simplest states, (c) Find the frequency of each of these states.
Three forces are exerted on the disk shown in Figure P12.71,and their magnitudes are F3 = 2F2 = 2F1. The disks outer rimhas radius R, and the inner rim has radius R/2. As shown in thefigure, F1 and F3 are tangent to the outer rim of the disk, and F2 is tangent to the inner rim. F3 is parallel to the x axis, F2 is parallel to the y axis, and F1 makes a 45 angle with the negative x axis. Find expressions for the magnitude of each torque exertedaround the center of the disk in terms of R and F1. FIGURE P12.71 Problems 71-75
Reciprocating motion uses the rotation of a motor to produce linear motion up and down or back and forth. This is how a reciprocating saw operates, as shown below. If the motor rotates at 60 Hz and has a radius of 3.0 cm,estimate the maximum speed of the saw blade as it moves up and down. This design is known as a scotch yoke.
Two forces are applied to an eye bolt fastened to a beam. Use the cosine rule and the sine rule to determine the magnitude and direction of their resultant force
Your roommate is working on his bicycle and has the bike upside down. He spins the 56.0 cmcm -diameter wheel, and you notice that a pebble stuck in the tread goes by three times every second. What is the pebble's acceleration? Express your answer with the appropriate units.
3) A shaft turning at 750rad/s slows to a stop in 6.55 seconds. What is the angular displacement the shaft rotates during this time?