Which layer (aqueous or organic) would you expect to find 3,5-dimethylaniline in the following liquid- liquid extractions? Explain. Draw chemical structures to help explain your answers. If the structure of the molecule changes in the aqueous solution, then draw the new structure. i. water and dichloromethane ii. aq. NaOH and dichloromethane iii. aq. HCl and dichloromethane

Which layer (aqueous or organic) would you expect to find 3,5-dimethylaniline in the following liquid- liquid extractions? Explain. Draw chemical structures to help explain your answers. If the structure of the molecule changes in the aqueous solution, then draw the new structure. i. water and dichloromethane ii. aq. NaOH and dichloromethane iii. aq. HCl and dichloromethane

EBK A SMALL SCALE APPROACH TO ORGANIC L

4th Edition

ISBN:9781305446021

Author:Lampman

Publisher:Lampman

Chapter81: Extractions, Separations, And Drying Agents

Section: Chapter Questions

Problem 8P

See similar textbooks

Similar questions

What is the purpose of adding sodium sulfate to the organic layer after extraction? A. To remove water from the organic phase B. To act as a base to deprotonate the tannins, making them water soluble C. To act as a base to deprotonate the caffeine, making it water soluble D. To remove organic solvents from the aqueous phase
If you had performed the extraction with dichloromethane (d 1.33 g/mL) as the organic solvent and just water as the aqueous layer, describe what is the top and bottom layer and which layer would each of the three starting compounds (benzil, benzoic acid, and alizarin) would be found in.
If 1.0g of hyoscyamine was dissolved in 200mL of water, how much hyoscyamine would be left remaining in the aqueous solution after extracting once with 100mL of diethyl ether? How much hyoscyamine would be left remaining in the aqueous solution if two extractions with 50mL of diethyl ether were performed instead? Which extraction method would be more efficient at removing hyoscyamine from the aqueous solution? The partition coefficient, K, of hyoscyamine in this system is 4.07.
1. What is the reason behind the portion-by-portion evaporation of DCM in the extraction of eugenol? 2. Enumerate some pharmaceutical and medical uses of eugenol 3. What does the ferric chloride test identify? Is it specific test for eugenol? Why or why not?
1.So if you were trying to extract 15mL of an aqueous layer, why wouldn’t you want to use 45mL of theorganic solvent? Why would 20mL be better? 2.Why wouldn’t you use 2mL of the organic solvent?
1. Briefly discuss the roles of (1) placing tea bags in boiling water, and (b) addition of anhydrous sodium sulfate in the isolation of the alkaloid. 2. Some procedures include the addition of sodium carbonate before liquid-liquid extraction. What is the purpose of this step? 3. Give at least three characteristics of dichloromethane that makes it a good extracting solvent for the alkaloid. 4. Why is it necessary to remove a stopper from a separatory funnel when the liquid is being drained from it through a stopcock? 5. What are emulsions? Why do they form during extractions? How is the formation of an emulsion minimized? How are emulsions removed?
Account for the greater amount of internal pressure in the aspirin extraction versus the ß- naphthol extraction.Why does the sequence for extracting the diethyl ether solution of aspirin acid, naphthalene, and ß-naphthol start with aqueous bicarbonate and follow with aqueous hydroxide rather than the reverse order?
In addition to a low boiling point and immiscibility with water, why is density important to consider in the selection of an extraction solvent? Would an organic liquid with a density of 1.006 g/mL make a good extraction solvent? Explain.Write the chemical reaction that took place during this experiment.
In the first part of your extraction, you added NaOH until the pH was 8. Why is a pH of 8 desired? Why is this pH 8 desired when isolating or extracting caffeine from a drink?
What is the reason behind the portion-by-portion evaporation of DCM in the extraction of eugenol?
in a liquid-liquid extraction, why is ethyl acetate a good initial solvent to dissolve a mixture of benzoic acid, 4-bromoacetophenone and ethyl 4-aminobenzoate? the extraction solvent is sodium bicarbonate.
We want to extract terpenoids from an aqueous sample by continuous liquid-liquid extraction. Which of the following solvents is not suitable for this purpose? Why? Propanone (acetone), dichloromethane, heptane.