Which multiplexing technique transmits analog signals?Select one:O a. TDMO b. FDMO c. DCMO d. CDM What is the maximum data rate of a channel with a bandwidth of 200 KHz if weuse four levels of digital signaling.Select one:O a. 400 bpsO b. 200 bpsO c. 600 bpsO d. 800 bps

Frequency division multiplexing(FDM) is the multiplexing used to transmits analog signals. b.FDM…

Answered: Which multiplexing technique transmits…

Engineering

Computer Science

Which multiplexing technique transmits analog signals? Select one: O a. TDM O b. FDM O c. DCM O d. CDM

Fundamentals of Information Systems

9th Edition

ISBN:9781337097536

Author:Ralph Stair, George Reynolds

Publisher:Ralph Stair, George Reynolds

Chapter4: Networks And Cloud Computing

Section: Chapter Questions

Problem 4RQ

See similar textbooks

Related questions

Q: What are the most commonly used transmission speeds in BPS used in data communication? a. 500 b.…

A: Given that: What are the most commonly used transmission speeds in BPS used in data…

Q: 49.8 dB 5. The communication system in figure beside represent: 110 a-4 channels FDM b- 4 channels…

A: Solution:

Q: Analog transmission has been around for a long time, but digital transmissions are more recent.…

A: Analog transmission is a means of transmitting speech, data, images, signals, or video. It employs a…

Q: Advantages of digital communication are O a)Easy multiplexing b)Easy processing O c)Reliable d)All…

A: Actually given question regarding digital communication.

Q: What is multiplexing and how does it benefit you?

A: Introduction: The following are the primary benefits of multiplexing. A single medium may carry more…

Q: Which type of guided medium is the least susceptible to attenuation and inductance? a. Coaxial…

A: Answer as follows:

Q: What is the difference between Simplex, Half Duplex, and Full Duplex? What is the importance of…

A: INTRODUCTION: In the given problem statement, we are asked the difference between transmission modes…

Q: A noiseless channel with a bandwidth of 'B' Hz is transmitting a signal with 16 signal levels. Then…

A: In this problem, we will calculate the maximum bit rate passing through a noiseless channel.

Q: nt from one

A: TDM-Time-division multiplexing (TDM) is a method for communicating and getting independent signals…

Q: What will be the frequency of the carrier for an AM wave, if its highest frequency is 850 Hz and the…

A: Upper frequency =850 HzBandwidth =50 HzTherefore lower Frequency =850−50=800 HzCarrier Frequency…

Q: Computer science Which has the higher efficiency, synchronous TDM or statistical TDM?

A: Introduction: Each input connection is separated into units in Synchronous TDM, and each input fills…

Q: () Suppose you have an analog signal, explain how will you convert it to digital signal?

A: Analog signals are continuous signals which contains infinite values between two points on signal.…

Q: 218. The bandwidth of analog switched service in between a. 300 and 3300 Hz b. 0 and 4000 Hz c. 600…

A: The bandwidth of analog switched service in between

Q: B-fill the blanks below: (answer five only) 1- The maximum peak-to-peak voltage of an AM wave is 200…

A: Q-1) Maximum voltage Vmax =2002= 100mV Minimum voltage Vmin =52=2.5 mV Modulation Index…

Q: 1) A transmission that generally involves dedicated circuits. i. simplex ii. half duplex iii.…

A: Computer network: A computer network is a group of systems or nodes that communicate with each other…

Q: Q1: illustrate which of the following sentence is TRUE or FALSE and correct the wrong one: 1. In…

A: Digital communication is the method of sending and receiving information through various digital…

Q: Find the minimum bandwidth of a FDM system which multiplex five

A: The answer is

Q: Give five examples of how the UHF band is used.

A: Introduction: UHF stands for Ultra High Frequency.

Q: Why is statistical TDM a better multiplexer than synchronous TDM? In TDM, why is the synchronization…

A: Introduction: Statistical TDM: The time-division multiplexing(TDM) that does not use synchronization…

Q: In a nutshell, how does wavelength division multiplexing work?

A: Introduction: Division of Wavelength Multiplexing is a fiber-optic transmission technology that…

Q: If the baud rate for a 64-QAM signal is 2000, what is the bit rate

A: Q: If the baud rate for a 64-QAM signal is 2000, what is the bit rate?

Q: Multiplexing and De-Multiplexing?

A: The multiplexer, shortened to “MUX” or “MPX”, is a combinational logic circuit designed to switch…

Q: Describe the concept of multiplexing?Describe methods that can achieve multiplexing. Discuss the…

A: multiplexing is a technique used to combine and send the multiple data streams over a single medium.…

Q: Subject - Data Communication Networks 1. What features are true about of Time Division…

A: Multiplexing is used when a single transmission medium needs to be shared. Suppose there is a single…

Q: A device that converts one type of signal into another is called A. Modem B. Transducer C. Punched…

A: Question given: A device that converts one type of signal into another is called - Right Answer:…

Q: Which has the higher efficiency, synchronous TDM or statistical TDM?

A: Which has the higher efficiency, synchronous TDM or statistical TDM?

Q: In transmission, the medium carries signals in both directions at the same time. O a. both full…

A: In simplex transmission mode, Sender can send signals but that sender can’t receive the signal. In…

Q: DSL is a combination of what two types of multiplexing? a. FDM and TDM b. FDM and FM c. AM…

A: DSL (Digital Subscriber Line) is a technology that allows you to send and receive data over phone…

Q: Converting analog signals to digital signals and digital signals to analog signals can be done using…

A: Modem can convert analog to digital signals.

Q: AMPS uses ______ to divide each 25-MHz band into channels. a. FDMA b. TDMA c. CDMA d. none of the…

A: Given that: The topic is about AMPS uses in FDMA.

Q: What is the earliest twisted-pair cabling standard that meets the minimum requirements for 10GBase-T…

A: "Cat 6a" is known as the earliest twisted-pair cabling standard that satisfies the minimum…

Q: QUESTION 9 A digital signaling system is required to operate at 4800 bps. If a signal element…

A: C = 4800 kbps n = 4 B.W = ? Log 2 M = 4 C = 2 B.W log₂ M C = 2(B.W) (4) = 24000 B.W =300000 HZ

Q: how does Orthogonal Frequency Division Multiplexing (OFDM) works?

A: Orthogonal frequency-division multiplexing (OFDM): A technique for data transmission known as…

Q: Compare the transition from analog repeaters to digital regenerators for copper-based transmission…

A: Compare the transition from analog repeaters to digital regenerators for copper-based transmission…

Q: The following table summarizes the advantages and disadvantages of the main communication channels.…

A: A communication channel can be denoted as the method of data or information flow within a company or…

Q: Q1. The output current of a 60 percent modulated AM generator is 1.5 A. To what value will this…

A: The answer for the given question is a s follows.

Q: 4. Digital receivers can receive both analog and digital signals. 5. If the power of a signal is…

A: To Do: To declare statements true or false.

Q: Compared to analog signals, digital signals

A: Analog Signals : These are used in many systems to produce signals to carry information These…

Q: Q9/ The bandwidth of amplitude modulation (AM) if a sinusoidal signal at 1.5 KHz, a) 3KHz Ob) 1.5Hz…

A: Given signal frequency = 1.5 KHz The bandwidth of amplitude modulation = 2*signal frequency

Q: What is OFDM? (Orthogonal Frequency Division Multiplexing) Advantages and Disadvantages of OFDM:…

A: Introduction: In an OFDM transceiver, the bits are first mapped into complex symbols by a bank of…

Q: An FM modulated signal has the form ?(?) = 50 cos(? 107 ? + 2 cos(4000??)) Determine 1. the average…

A: Required: Determine1. the average transmitted power2. the peak-phase deviation3. the peak-frequency…

Q: 25.A. Which of the following could inoti be a SONET transmission rate? A. 9.953 Gbps B. 99.66 Mbps…

A: Introduction 25.A. Which of the following could inoti be a SONET transmission rate?A. 9.953 GbpsB.…

Q: In data communications, the non periodic signals a. Sine wave b. Digital Signals c. Analog Signals…

A: The Answer is in Below steps

Q: Q.5.3 Briefly describe how Wavelength Division Multiplexing works.

A: Given: Q.5.3 Briefly describe how Wavelength Division Multiplexing works.

Q: A digital signal is a composite analog signal with Infinite bandwidth why?

A: A digital signal is a composite analog signal with an endless transfer speed. Baseband transmission…

Q: Why do we need multiplexing? Distinguish between the two basic multiplexing techniques (FDM and TDM)…

A: The answer is given below:-

Question

Which multiplexing technique transmits analog signals?
Select one:
O a. TDM
O b. FDM
O c. DCM
O d. CDM

What is the maximum data rate of a channel with a bandwidth of 200 KHz if we
use four levels of digital signaling.
Select one:
O a. 400 bps
O b. 200 bps
O c. 600 bps
O d. 800 bps

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

A line has a signal-to-noise ratio of 1000 and a bandwidth of 4000 kHz. What is the maximum data rate supported by this line? If the bandwidth of the channel is 5 kbps, how long does it take to send a frame of 100,000 bits out of this device? What is the maximum data rate of a channel with a bandwidth of 200 kHz if we use four levels of digital signaling?
Assume that a voice channel occupies a bandwidth of 8 kHz. We need to multiplex 10 voice channels with guard bands of 1000 Hz using FDM. Calculate the required bandwidth
60. Ten signals, each requiring 3000 Hz, are multiplexed on to a single channel using FDM. How much minimum bandwidth is required for the multiplexed channel ? Assume that the guard bands are 300 Hz wide. a. 30,000 b. 32,700 c. 33,000 d. None of the above
Four channels, two with a bit rate of 120kbps and two with a bit rate of 880kbps, are to be multiplexed using multiple-slot TDM with no synchronization bits.Answer the following questions: a. What is the size of a frame in bits? b. What is the frame rate? c. What is the duration of a frame? d. What is the data rate?
Assume having a low-pass noiseless channel that spans from a Frequency of 0Hz to 130Hz, to send at a bit-rate value that is not less than 1Kbps, then you would at least need ................. signal levels.
Ten signals, each requiring 3000 hz, are multiplexed onto a single channel using FDM. How much minimum bandwidth is required for the multiplexed channel? Assume that the guard bands are 300 Hz wide.
Is it true that a narrowband channel transfers data at a snail's pace? Why?
Ten signals, each requiring 4000 Hz, are multiplexed onto a single channelusing FDM. What is the minimum bandwidth required for the multiplexed channel? Assume that theguard bands are 400 Hz wide.
Suppose, BanglaLink has 4 voice channels, each of 60Mbps. They use synchronous TDM to multiplex these channels. If 3 characters at a time are multiplexed (3 characters in each output slot), 1. Draw the first two output frames with arbitrary inputs. 2. What is the size of an output frame in bits? 3. What is the output frame rate? 4. What is the duration of an output frame?
1) What is the major factor that makes coaxial cable less susceptible to noise than twistedpair cable? (a) Inner conductor (b) Diameter of cable (c) Outer sheath (d) Insulating material 2) Aliasing can be defined as errors occurring when (a) The sample rate exceeds twice the input frequency.(b) The bandwidth is less than the input frequency.(c) The number of bits per sample is low.(d) The sampling signal has been incorrectly identified. 3) In _______encoding, three levels are used: positive, zero, and negative. (a) Unipolar RZ (b) Bipolar RZ (c) Polar NRZ (d) Manchester NRZ 4) The ________ rate defines the number of data elements sent in 1sec; the ______ rate isthe number of signal elements sent in 1sec. (a) data; signal (b) signal; data (c) bit; baud (d) baud; bit5) The channel capacity of a noiseless channel can be improved by (a)Increasing the signal-to-noise ratio. (b) Decreasing the channel bandwidth.(c) Applying error correction technique. (d) Applying M-ary modulation scheme. 6)…
Suppose BanglaLink has 40 voice channels, each of 60 Mega Bytes per Second. They use synchronous TDM to multiplex these channels. If four characters at a time is multiplexed (four characters in each output slot), answer the following questions: iv) What is the output data rate? v) Input bit duration? vi) Output bit duration?