Which of the following best describes a conventional electric current? a.jt produces electric charges D.It is the same as electric charge C.it is produced by moving positive charges d.it is produced by moving hegative charges 2. What must be the value of R in the network of resistors for the total Tesistance to be 10 n? 6.00 5.00-R Wr W-W 3.00 6.00 8.00 a.6.0 0 D.5.0 0 C.4.0 0 d.3.0 0 3. Which of the following graphs represents the relation between the resistance of a uniform wire and its cross sectional area? a. R/ C. R A d. R

Which of the following best describes a conventional electric current? a.jt produces electric charges D.It is the same as electric charge C.it is produced by moving positive charges d.it is produced by moving hegative charges 2. What must be the value of R in the network of resistors for the total Tesistance to be 10 n? 6.00 5.00-R Wr W-W 3.00 6.00 8.00 a.6.0 0 D.5.0 0 C.4.0 0 d.3.0 0 3. Which of the following graphs represents the relation between the resistance of a uniform wire and its cross sectional area? a. R/ C. R A d. R

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Consider the circuit configurations below, where two lightbulbs are connected to a single battery in different ways. Based on what you learned about parallel and series connections in lab, which of these two configurations would result in the light bulbs being the brightest? Fully explain your reasoning. Imagine that you are given four 100Ω resistors to build a circuit. Your challenge is to use all four of the resistors in the circuit, but the circuit must have an overall equivalent resistance of 100Ω. Is this possible? If so, draw a diagram of the circuit and explain how the connections result in a 100Ω equivalent resistance. If this is not possible, draw a diagram of a circuit involving all four resistors that has an equivalent resistance as close to 100Ω as is possible.
Directions: Solve for the given problems. Show your complete solutions. Express your final answers into 3 significant figures. The terminal voltage of the battery in figure 4 is 16.6 V. What is the resistance R of the external resistor? What is the internal resistance r of the 18.0-V battery? What should be the diameter of an aluminum wire for its resistance to be equal to that of a copper wire which diameter is 2.17 mm? The two wires are of the same length. ρ (Copper) = 1.68 x 10-8 Ωm ρ (Aluminum) = 2.65 x 10-8 Ωm
Directions: Solve for the given problems. Show your complete solutions.Round off your answers into the proper number of significant figures.1. Copper has 8.5 x 1028 free electrons per cubic meter. A 75.0-cm length ofcopper wire with a diameter of 2.05 mm, carries 4.97 A of current.a. How much time does it take for an electron to travel the length of thewire?b. Repeat (a) for a wire with a diameter of 4.12 mm of the same length thatcarries the same current.c. How does changing the diameter of the wire affect the drift velocity ofthe electrons in the wire?
Solve the following Physics problem. Show your solutions. Round off your final answer in a whole number. An electric flat iron draws a current of 15 A when connected to a 110 V line. (A.) Assuming that the heating element of the flat iron obeys Ohm’s Law, what is its resistance? (B.) What is the resistivity of the heating element if it is a wire that is 2.5 cm long with cross-sectional area of 2x10-4 cm long.
Answer the following. Write your solution and box your final answer on each question. 1. What charge flows past a point in a wire in 6.0 s if the wire carries a current of 2.0 A? 2. If a circuit element can withstand a maximum current of 15 A, how many electrons can pass through it each second?3. How many electrons are transferred in a 10.0 A current that runs for 3.0 s?4. If 2.00 × 102mA of current flows through the filament of a light bulb, how many electrons would pass through the filament in 30.0 s?5. What feature of a river is most similar to current in an electric circuit? (A) The depth of the river measured in meters (B) The temperature of the water measured in degrees Celsius (C) The vertical drop between two points along the river measured in meters (D) The volume of water moving past a point measured in liters per second
Please fill out the template below with the work for this problem. Note that you need to have a picture, a list of knowns and unknowns, the general equation/s you will use, and the math steps to solve for the unknown, only plug in the numbers after you have solved for the unknown, and the answer with units included. Question 1: A current of 2.72 A flows through a wire. How many electrons flow past a particular point in the wire every 15 seconds?
Directions: Solve for the given problems. Show your complete solutions.Round off your answers into the proper number of significant figures.2. The current in the wire varies with time according to the relation I = 55 A –(0.65 A/s^2)t^2.a. How many coulombs of charge pass a cross-section of the wire in thetime interval between t = 0 and t = 8.0 s?b. What constant current would transport the same charge in the same time interval?Note: In problem 2, A means ampere, s means second.
Three resistors having resistances of 4.0 Ω, 6.0 Ω, and 10.0 Ω are connected in parallel. If the combination is connected to an ideal 12-V. What is the total resistance of the circuit? What is the current through each resistor? What is the power dissipated by the 6.0 Ω resistor? Clearly state the formulae you’re using and what your letters/symbols mean.
Three resistors having resistances of 4.0 Ω, 6.0 Ω, and 10.0 Ω are now connected in series. If the combination is connected to an ideal 12-V. What is the total resistance of the circuit? What is the current through each resistor? What is the voltage drop across each resistor? What is the power dissipated by the 6.0 Ω resistor? Clearly state the formulae you’re using and what your letters/symbols mean.
I attached the picture of the question, but just in case it is hard to read here it is typed out! Also, I need the answers correct to 4 decimal places. Thank you!! The figure shows how a bleeder resistor is used to discharge a capacitor after an electronic device is shut off, allowing a person to work on the electronics with less risk of shock. The resistor has a resistance of 302 kΩ. a. What is the time constant? (in s) b. How long will it take to reduce the voltage on the capacitor to 1.0% of its full value once discharge begins? (in s) c. If the capacitor is charged to a voltage ?0 through a 120 Ω resistance, calculate the time it takes to rise to 0.9?0 (This is close to two time constants.) (in ms)
Bill is working on an electrical circuit problem. He remembers from his electrical engineering class that voltage drop ΔE is a function of electrical current I and electrical resistance R. Unfortunately, he does not recall the exact form of the equation for ΔE. However, he is taking a fluid mechanics class and decides to use his newly acquired knowledge about dimensional analysis to recall the form of the equation. Help Bill develop the equation for ΔE using the method of repeating variables, showing all of your work. Compare this to Ohm’s law—does dimensional analysis give you the correct form of the equation
Solve the problems below. Make sure to show proper solution. All finalanswers should be written inside a box. 3. The electric field of the material between two coaxial cables of radius .25 m and .51m is given as E = 2.58 V.m/r3. If the conductivity of the material is 5 x 1010 S/m, whatis the current density in the material?