Give small explanation also. Which of the following is least effective in on managing edge cracks in rolling process?reducing draftincreasing roll shaft radiusincreasing capacity of rolling millapplying front and/or back tensionincreasing workpiece temperatureThe best process to make reinforced structural beams and profiles is:Blown Film ExtrusionVacuum Bag MoldingPultrusionThermoformingcastingBlow MoldingExtrusionReinforced Plastic SheetsCalendaringNone of these options

Rolling process can be defined as a method in which a metal stock is passed rollers in order to…

Which of the following is least effective in on managing edge cracks in rolling process? reducing draft increasing roll shaft radius increasing capacity of rolling mill O applying front and/or back tension O increasing workpiece temperature The best process to make reinforced structural beams and profiles is: Blown Film Extrusion Vacuum Bag Molding Pultrusion Thermoforming casting Blow Molding Extrusion Reinforced Plastic Sheets Calendaring None of these options

Which of the following is least effective in on managing edge cracks in rolling process? reducing draft increasing roll shaft radius increasing capacity of rolling mill O applying front and/or back tension O increasing workpiece temperature The best process to make reinforced structural beams and profiles is: Blown Film Extrusion Vacuum Bag Molding Pultrusion Thermoforming casting Blow Molding Extrusion Reinforced Plastic Sheets Calendaring None of these options

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the steel ratio that will produce a tension-controlled failure if compressivestrength f’c = 28 MPa and steel yield strength fy the answer is 0.02167 but i don't know how to solve it please help
Answer using Bond development length hooks and splicing of reinforcement in RCD NSCP 2015. The answer is A) 1257mm B)Ld=866.614mm I need a complete solutions with step by step..
Name two differences between flexural and local buckling.
Based from color, what is the major indicator wether a reinforcing steel bar is weldable or not?
P01 : What does the grade stamp on the lumber identifies? a. Species of lumber b. The mill that produced the piece c. Inspection agency d. Moisture content at the time of surfacing e. Dimension of the lumbar f. All of the above P02: A 4x16 (green) DF-L swan timber beam and a 3.5x15 DF glulam beam are considered for use in a structure with an expected moisture contnet of 10%. Find the expected shrinkage of each membeer through the depth assumiong the initial moisture content is 30% for the swan lumber and 14% for the glulam.
A grade 36 round steel bar with a diameter of 0.5 inches and a gauge length of 2 inches wassubjected to tension to rupture following ASTM E-8 test procedure. The load and deformation data wereas shown in the following table: Using a spreadsheet program obtain the following:a. A plot of the stress-strain relationship. Label the axes and show units.b. A plot of the linear portion of the stress-strain relationship. Determine modulus of elasticity usingthe best fit approach.c. Proportional limit.d. Yield stress.e. Ultimate strength.f. When the applied load was 4.07 kips, the diameter was measured as 0.499905 inches. DeterminePoisson’s ratio.g. After the rod was broken, the two parts were put back together and the diameter of at the neckwas measured as 0.416012 inches. What is the true stress value at fracture? Is the true stress atfracture larger or smaller than the engineering stress at fracture? Why?h. Do you expect the true strain at fracture to be larger or smaller than the…
A nail joint is subject to medium term tensile loading under service class 2. The joint comprises of eight 3.75 x 60 mm long round wire in single shear in C18 timber. What is the slip modulus? Question 4Answer a. 780.38 b. 550.69 c. 625.37 d. 659.19
GIVE 10 DISADVANTAGES OF USING HOLLOW BLCOKS.
A wood specimen was subjected to bending until failure by applying a load inthe middle of its span. The specimen has a cross section of 25 mm * 25 mm(actual dimensions) and a span of 350 mm between the simple supports. Theload and the deflection in the middle of the span were recorded as shown inTable P10.22.a. Using a computer spreadsheet program, plot the load–deflectionrelationship.b. Plot the proportional limit on the graph.c. Calculate the modulus of rupture (flexure strength).
UPVOTE will be given! Please write the solutions completely and legibly. Box the final answer. Use two decimal places. ANSWER "B" AND "C" ONLY A reinforced concrete beam 30 mm x 300 mm with tensile reinforcement of 1 - 28mmØ is simply supported over a span of 5.5 m. Using steel covering of 75 mm, concrete strength is 20.7 MPa and yield strength of re-bars is 280 MPa. a. Determine the cracking moment of inertia. (I attached the answer. Check the photos uploaded) b. Determine the moment capacity of the beam. c. Describe the mode of design.
Differentiate Allowable Stress Design (ASD) with Allowable Strength Design (ASD) design procedure. Give examples as much as possible.
Q3: Sample of marble stone with length of 45 cm. Find the width and thickness (b, d) with logical thickness that give the modulus of rupture =4 MPa and failure load (P = (3 kN) and larger area of floor tiling. If you know that load span in flexural is (L= 40 (0100 ) RSPRVIPCSD EOL{PH] [ ESES P Y.L