Define briefly with correct answer don't copy from others source please ... A pinion with radius r, and inertia 4 is driving a gearwith radius r, and inertia I,. Torque t, is applied onpinion. The following are free body diagrams of pinionand gear showing important forces (F, and F2) ofinteraction. Which of the following relations hold true?F20,,0, = AngularDisplacementsF.Inertia = 1,Inertia = 12(A) F # F2; T1 = 1,8,; F2 = l20r22(B) F, = F;: T, = [4+2 (T: =,(C) F = F2; T1 = 1,0;; F2 = I2-62%3Dr22(D) F, # F2, T1 = 4+l2 )0,; F2 = 1202

Given: A pinion with radius r1 and inertia I1 is driving a gear with radius r2 and inertia I2.…

Answered: Which of the following relations hold…

Engineering

Mechanical Engineering

Which of the following relations hold true?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A spur pinion of pitch diameter 50 mm rotates at 200 rad/s and transmits 3 kW power. The pressure angle of the tooth of the pinion is 20°. find the total force exerted by a tooth of the pinion on other gear?
Provide very clear and complete solution and diagam. SITUATIONAL PROBLEM: Two shafts are connected by spur gears. The pitch radii of the gears A and B are 200 mm and 860 mm respectively. If shaft A makes 350rpm and is subjected to twisting moment of 250 N-m. Pressure angle is 14.5 degree. What is: a.) Rpm of gear B b.) Torque in shaft B (in Newton meter). c.) Separation load of two gears (in newtons). d.) Total load on gears (in newtons).
Qv quality number for camberless straight bevel pinion gear with 20 teeth and a modulus of 4 mmis 6. Made of 1st quality steel, with a hardness of 300 HB, the pinion and the reciprocating gear are completelyhardened. The rotated gear has 60 teeth. Pinion life is 109 cycles and reliabilitycoefficient is 0.999. Shaft angle is 90o, pinion rotation speed is 900 rpm. Tooth width 32 mm andThe normal pressure angle is 20o. Based on AGMA bending strength, the strength of the gear systemcalculate. Load factor Ko =1, safety factor SF =1.
8.7 A pair of involute gears with 16° pressure angle and 6 mm module is in mesh. The number of teeth on pinion is 16 and its rotational speed is 240 r.p.m. When the gear ratio is just 1.75, find, in order that the interference is just avoided, (a) the addenda on pinion and gear wheel (b) the length of path of contact, and (d) the maximum velocity of sliding of teeth on either side of the pitch point. (DAV Indore, 1989) (Ans. a, 9.6 mm; a 4.2 mm; 35.41 mm; V = 95.58 cm/s) %3D
Two mating involute spur gear of 20° pressure angle have a gear ratio of 2. The number of teeth on the pinion is 20 and its speed is 250 r.p.m. The module pitch of the teeth is 12 mm. If the addendum on each wheel is such that the path of approach and the path of recess on each side are half the maximum possible length, find : a. The addendum for pinion and gear wheel; b. The length of the arc of contact; c. The maximum velocity of sliding during approach and recess. Assume pinion to be the driver.
In a single-stage gear wheel system with an evolvent profile, the rotating (driveThe number of teeth of the gear is Z1=10, the number of teeth of the rotated gear is Z2=20 and the modulus is m=5 mm; The rotating gear rotates clockwise. b)Show the useful working length and the limit working length on the figure
In a single-stage gear wheel system with an evolvent profile, the rotating (driveThe number of teeth of the gear is Z1=10, the number of teeth of the rotated gear is Z2=20 and the modulus is m=5 mm; The rotating gear rotates clockwise. d) Prevent undercutting, if it exists on the same shape, by enlarging the grip angle. Calculate the value of the new grip angle and compare it with the new grip angle value you obtained from the drawing.
A parallel helical gear set of 19 tooth pinion is driving a 57 tooth gear. The helix angle of 20 degrees while the normal pressure angle is 14.5 degrees and the normal diametral pitch of 10 teeth/inch. If the pinion is rotating at 1800rpm and transmits 50hp, find the normal force. Please answer in detailed solution.
You want to design a gear for a machine in a company that you are working in. Figure 2 shows wheel A of radius ra =10 cm is coupled by belt B to wheel C of radius re=25 cm. The angular speed of wheel A is increased from rest at a constant rate of 1.6 rad/s?. Find the time needed for wheel C to reach an angular speed of 100 rev/min, assuming the belt does not B Figure 2:Problem 5. slip. (Hint: If the belt does not slip, the linear speeds at the two rims must be equal.)
A 20◦ helical gear has tangential force of 200lb and helix angle of 16◦ and face width of 0.6”.If the machining error is 0.6 and pitchline velocity is 400ft/min. Determine radial force, axial force, normal force, normal pressure angle and dynamic load.
pinion having 20 involute teeth of module pitch 6 mm rotates at 200 r.p.m. and transmits 1.5 kW to a gear wheel having 50 teeth. The addendum on both the wheels is 1/4 of the circular pitch. The angle of obliquity is 20°. Find (a) the length of the path of approach ; (b) the length of the arc of approach; (c) the normal force between the teeth at an instant where there is only pair of teeth in contact.
A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14,5. The wheelchair has a maximum velocity of 5 m/s when it's pinion rotates at 800 rpm. Calculate : 1.1)The magnitude of the velocity of slip of gears in mesh 1.2)The angular speed of the gear wheel in rad/s 1.3)The maximum length of a path of the approach in mm 1.4)The length of a path of a recess in mm. 1.5) The addendum of the gears in mm. 1.6) The contact ratio