Which of the following requires the most work done by the brakes of a car? a) slowing down from 80 m/s to 55 m/s  b) equal amounts of work for both  c) stopping from 55 m/s

Q: Which of the following is a true statement: (i) Kanban and 5S system were used to minimise or…

A: Concept: 1) Kanban and 5S technique as used to eliminate waste by effective utilisation of…

Q: The distance depends on the observer’s relative motion. Explain the statement.

A: Given Data⇒relative motionProblem definition⇒Problem says The distance depends on the observer’s…

Q: 2/y Y+1/Y 2Cp ma Q1/ Show that Cda Cdf %3D Af 2Pr(P1-P2-zxgxpp) actual

A: When compressibility of air is considered the air flow rate is changed but the fuel flow rate is…

Q: ) With a neat sketch explain about Induced soft foot

A:

Q: 10 times larg solf hell is uC

A:

Q: Need asap in 30 min i will give like

A: Given,

Q: How much change in the power of wind will take place if wind velocity becomes 3 times and blade…

A: To determine the change in power of the wind if the velocity of the wind becomes 3 times and length…

Q: A. Explain in detail corrective maintenance and state two (2) disadvantages of it B.What is…

A: Solution:

Q: List safety precautions that you should observe when operating a tractor on the field during field…

A:

Q: Briefly explain the different between statics friction and kinetics friction.

A: Given data Briefly explain the different between statics friction and kinetics friction.

Q: Friction creates heat. Select one: True False

A:

Q: If a wind turbine is facing a wind velocity of 23.4 m/s, then it is Select one: a. Survival speed b.…

A: Solution: The maximum wind speed is also known as the maximum survival speed, is the speed above…

Q: and the restorer

A:

Q: Explain about hydraulic and Maintenance for automotive Industries (procedure and application

A: In every industry, there is a set of machinery is employed. After some time these machines need some…

Q: 20. You should replace the pulleys on a power transmission system every A. fourth belt change. B.…

A:

Q: Which of elstomer is used to make car tyres? Answer:

A: (a) Elastomer: Elastomers are natural or synthetic polymers that have an elastic property.

Q: What is Double-Acting Unbalanced Linear( Landing Gear). Give some application examples of it.

A: The landing gear is used in aviation structures which are used to give support to an airplane during…

Q: THE LOAD SAFELY OR NOT O =1024 KG/CM? 18 T 90cm 20 cm 36 cm + 4 m. 5 m. 20 cm

A: Bending stress When some load is subjected to the beam then shear stress and bending moment act on…

Q: Which of the following is a digital transducer

A: A. Strain gauge It is in the form of strip which is used to measure strain of a body. Change in…

Q: List any four limitations of using conventional energy sources

A: There are two main sources of energy which can be written as below, 1. Source of conventional type…

Q: Which of the following is an accurate statement? A The direction of the angular momentum is…

A: option C is the correct answer

Q: Ps or ABS shows higher toughness and why?

A: Ps stands for polystyrene ABS stands for Acrylonitrile butadiene styrene

Q: What is a car

A: Given Data⇒ Car

Q: Industrial maintenance What two things cause accidents?

A: Industrial Maintenance Technicians install, repair and maintain commercial or industrial machinery…

Q: E. How far is the ship from the port at 11:00 A.M.? C) 32.78 km

A: Need to find the distance

Q: A chain drive is no longer considered horizontal when the line passing through both shafts has an…

A: A chain drive is no longer considered horizontal when the line passing through both shafts has an…

Q: Which of the following best defines the meaning of risk? A. The probability of an accident…

A:

Q: 130) What is the sensitivity of the vernier caliper? A) 0.05mm B) 0.0001mm C) 0.001mm D) 0.01mm E)…

A: (A) 0.05 mm (A) lead (D) Quality control

Q: Which can do work faster per unit time? (A) 2300-W engine (B) 3-hp engine (C) 1.5 kW engine (D)…

A: To solve this question, each options need a proper analysis and conversion into same units.

Q: The oil in the pump should be replaced after the first ____________ hrs. a. 200 b. 0.002 c.…

A: There is a thumb rule of changing for a oil-lubricated pumps...

Q: Explain about hydraulic and Maintenance for automotive Industries (procedure and applications)

A: Maintenance of the machinery is a very important part of the insutries. In every industry, there is…

Q: 1. The word pre-war means? a) before the war b) during the war c) after the war 2. What does the…

A: 1.      It refers to something that happened or existed before a conflict, particularly before…

Q: what is Mechanical Draft Cooling Tower and how its work

A:

Q: future which type of car/vehicle will replace the existing vehicles and why?

A:

Q: а. Briefly explain the different between statics friction and kinetics friction.

A: What is the different between static friction and kinetic friction?

Q: The energy gained due to friction in bearings is called Mechanical efficiency. Select one: True…

A: Correct answer is given below

Q: When discussing different types of energy; Technician A says that when energy is released to do…

A: both the technicians are wrong Explanation→ →when energy is released to do work it is actually…

Q: C. What is the main goal of a preventive maintenance (PM) program? Outline FOUR advantages of a PM…

A: Introduction: Preventive maintenance is a common strategy used by many enterprises, firms, and…

Q: The A 8000 lb TIT 6000 lb -4 ft. 10.000 lb 4 ft-> 4 4 ft → 4 fi B

A:

Q: a. How fast your car was traveling immediately before the brakes were applied b. The time required…

A:

Q: Make a problem where and object goes through three different energy changed. The oast change needs…

A: Make a problem where an object goes through three different energy changes. The last change is all…

Q: Which one of the following statement is a FALSE? O Frictional force does not depend on nature of…

A:

Q: 3. List some positive, negative impacts of automobile?

A: Automobile: It is a self-propelled vehicle, consists of internal combustion engine providing the…

Q: C)Write the effects of three different riders on the bicycle. Acceleration, deceleration, torque…

A:

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.