A chain drive is no longer considered horizontal when the line passing through both shafts has an angle greater than... 45 degrees. 60 degrees. 30 degrees 90 degrees

Q: ((2+ dy : 2 3 2 3 8/y - 4y +y² + C 8,/5 - 4y -y + c 2 3 8/y + 4y -yž + c 2 3 8/y + 4y + yž +C

A:

Q: Answer a) and b) only

A:

Q: Answer no. 2

A: Write the formula for maximum speed on the banked road. vmax=rgtanθ+μs1-μstanθ Here, vmax is the…

Q: In a vehicle when it is turned the axis of the wheel on the inside of curve turns through 45° angle…

A: Given data: -  The angle of the inside wheel is θ = 45o. The angle of outside wheel is φ = 30o. The…

Q: For the manipulator shown below: a) How many DOF are there? b) Draw the DH frames

A: Given that ;

Q: letrue 2. false

A: we are to decide of internal forces contribute to acceleration of force when it is being acted upon…

Q: higher or lower than that on the Earth lower than that on the Earth same as that on the Earth higher…

A: Given:

Q: maximum velocity of the follower

A: Given; Acc. to question,In a cam follower , the follower rises by h as the cam rotatesby δ…

Q: In thread cutting operation, pitch of thread is defined as а. Depth of thread b. Difference outer…

A: The distance between the two points starting from the one point on one thread to the…

Q: Answer (d), (e), and (f)

A: Given that, P1=1.4 MPa,T1=300 °C, At P=1.4 MPa   and   T=300 °C,v1=0.182 m3/kg,h1=3041…

Q: The major diameter of a thread is defined as what

A: A thread is a bank of the constant section in the form of a helix on the internal or external…

Q: PLETE SOLUTION PLS 4 DECIMAL PLACES  I SAW WRONG ANSWERS HE

A: Given:Patm=101 PabsA=150PgaugeB=30

Q: A windshield wiper rotates through a 120° angle as it cleans a windshield. From the point of…

A: Given data The angle turn by the blade is θ=120°=2.1 radian. The length of the wiper mechanism is…

Q: sure difference (Pa) between points A and B.

A: Given: To determine: The pressure difference between points A and B

Q: When two links of a mechanism become collinear (forming a straight line), the links are said to be…

A: A link is defined as a member of a mechanism that connects with other members of mechansim and…

Q: at A on the wall.

A: Answer= 14m/s

Q: Draw the free body diagram Always use 3 decimal place

A:

Q: 3) and B.d

A:

Q: Pictures A and B show two different ways of holding a workpiece in the vice while using hacksaw. The…

A: We have to given answer of above question Pictures A and B show two different ways of holding a…

Q: e airplane is degrees

A: 5.99deg

Q: A block is pulled

A: ANSWER=3.00 m

Q: Solve for a and b and c

A:

Q: When it comes to finding the moment arm, you must use the distance of the line from the pivot to the…

A: Explanation When it comes to finding the moment arm, you must use the distance of the line from the…

Q: which of the following statements

A: Given; In a composite slab the temperature at the interface (Tinter) between two materials is equal…

Q: angle of twist (a) between A and B, (b) between B and C, um (c) At C

A:

Q: 1.42. Expand (-4x – 1)² A. 16x2 +8x + 1 B. -4x2 + 8x + 1 С. C. 16x2 + 1 D. -4x2 + 1

A: Given data: The given equation is as follows: (-4x-1)2 This expression is the form of a+b2 The…

Q: The cosine law can be used when two ?angles are already known False

A: To determine whether the given statement is TRUE or FALSE.

Q: 2 Find T: For q=-KA when dr

A:

Q: D.5m/s) find the (H).

A: To find H

Q: Solve it Properly and with right answer.

A: Case-1 Given data: The inside diameter is, di = d. The outside diameter is, do = 1.5d. Calculate…

Q: Find the value of a if 13 2 |2a 1| 4 |-5 2 1 3 0 +- 4 -1 4 2 0 =101.

A: Given:

Q: etermine the equivalent ement is oriented 20° clo

A:

Q: distance s when the block stops. See figure (4).

A: the block will stop when the Kinetic energy , potential energy and work done by the force is…

Q: Compute the degree of freedom.

A: Number of links in the mechanism= 10 Number of joints in the mechanism= 12 Number of higher pairs in…

Q: Two parallel shafts, 36 inches apart are connected by a belt drive. The driving pulley rotates at…

A: GIVEN DATA DISTANCE BETWEEN SHAFT C=36in smaller pulley dia d=10in Larger pulley dia D=24 in We…

Q: Flat belt drives is used when the two pulleys not more than meters apart. O A 8 O B. 5 O C 15 O D.…

A: In a belt-drive, two or more than two shafts or pulleys are linked by a closed loop made up of…

Q: I need the answer for (a) (b) and (c) Thanks..

A:

Q: The energy gained due to friction in bearings is called Mechanical efficiency. Select one: True…

A: Correct answer is given below

Q: rope is wrapE

A:

Q: a. How fast your car was traveling immediately before the brakes were applied b. The time required…

A:

Q: the current (in A) required

A: Given; An electrochemical machining is to be used to cut a through hole intoThickness=12 mmHole has…

Q: e. Find the minimum diameter of the wire

A: for safe design stress induced in the rod should be less than or equal to the yield stress. so apply…

Q: A rod consists of two parts that are made

A: Kindly refer attached files.

Q: True or False: A fillet radius can be drawn between two parallel objects.

A: When filleting two parallel lines, a 180 degree arc will join the two lines. The radius of the…

Q: speed.

A: Given; A milling cutter having teeth is rotating at;  N= 135 rpmIf the tooth is, f=0.1 mmDetermine…

Q: 45 50 N

A: Given  Weight, W = 50 N         Angle = 45o Find   Tension in the cable, T1 and T2

Q: number of degrees of freedom

A: Number of links =6 Primary/lower pair joints=7 Higher pair joints =0

Q: The power output of

A: Given; Steam enters an adiabatic turbine operating at steady state with an;Enthalpy of,H=3251.0…