Which one of the following statements is correct?A beam is said to be of uniform strength, if(a) The bending moment is the same throughout the beam(b)(c)(d)[IThe shear stress is the same throughout the beamThe deflection is the same throughout the beamThe bending stress is the same at every section along its longitudinal axis

Bending Moment of the beam is defined as the rate of change of curvature along the length of the…

Which one of the following statements is correct? A beam is said to be of uniform strength, if (a) The bending moment is the same throughout the beam The shear stress is the same throughout the beam (b) (c) The deflection is the same throughout the beam (d) The bending stress is the same at every section along its longitudinal axis [I

Which one of the following statements is correct? A beam is said to be of uniform strength, if (a) The bending moment is the same throughout the beam The shear stress is the same throughout the beam (b) (c) The deflection is the same throughout the beam (d) The bending stress is the same at every section along its longitudinal axis [I

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.4P

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
The tensile strength of the beam given the loading condition and cross-section; since the tensile stress is 75 MPa and the compressive stress is 90 MPa, check the safety of the beam.
All of the following statements are correct except:a. Materials with higher modulus of elasticity, E are relatively weaker than those with lower E.b. Stress is proportional to strain within the elastic range.c. High carbon steel is stronger than concrete.d. In normal loading, the slope of the stress-strain curve is a material property called modulus of elasticity.The deflection of a beam is: A. Directly proportional to the modulus of elasticity and Moment of inertia B. Inversely proportional to the modulus of elasticity and moment of inertia C. Directly proportional to the load imposed and inversely to the length squared D. Inversely proportional to the weight and length
A square beam (w=0.03 m) is loaded with a point load of 1000 N and a moment load of 1000 Nm, as shown. i. Determine maximum deflection of the beam using step by step analytical equations. ii. Determine the Maximum stress in the beam using step by step analytical equations iii. For both top fibers and bottom fibers of the square beam, specify the type of the stresses.
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. P = 10 kN a. What is the stress (MPa) in the Bronze material? b. What is the stress in Aluminum in MPa? c. What is the stress in Steel in MPa?
Which of the following statements is incorrect for bending of a straight member? Bending stress of a point is proportional to its distance from the neutral axis of the section Bending stress is not a function of the moment of inertia of the beam section Bending stress is proportional to the bending moment of the section. Bending stress is inversely proportional to the moment of inertia of the beam section
When designing a structural member, which of the following statements is FALSE? A. The allowable stress is used in calculating the maximum load to be applied. B. The ultimate stress depends on the Factor of Safety used. C. The ultimate stress is determined based on the material used. D. The allowable stress depends on how conservative the design is. Which of the following is NOT a valid reason for increasing the Factor of Safety? A. Higher uncertainty in loading conditions B. Higher design life C. Lower confidence in assumed/stated material properties D. Lower member importance Which of the following occurs when the value of Poisson’s ratio is doubled and the modulus of elasticity is kept constant? a. The lateral deformations experienced by the material is halved b. The volume of the material will remain constant when subjected to external forces c. The elastic region of the shear stress-strain diagram would be less steep d. The material can withstand higher…
When designing a structural member, which of the following statements is FALSE? A. The allowable stress is used in calculating the maximum load to be applied. B. The ultimate stress depends on the Factor of Safety used. C. The ultimate stress is determined based on the material used. D. The allowable stress depends on how conservative the design is. Which of the following is NOT a valid reason for increasing the Factor of Safety? A. Higher uncertainty in loading conditions B. Higher design life C. Lower confidence in assumed/stated material properties D. Lower member importance Consider a 1,000-mm long, 25-mm diameter sample subjected to a tension test. Automatic high-precision gages recorded that for an applied load of 150 kN, the sample experienced a longitudinal strain of 2×10−3mm/mm. Assuming that the material remained elastic while loaded, determine its modulus of elasticity. A. 175.0 GPa B. 63.7 GPa C. 152.8 GPa D. 72.9 GPa
Defferentiate the following terms; 1.Resilience and proof resilience 2.proof resilience and modulus of resilience B)A solid beam ABC circular in section has varying sections.portion AB is 6m in length and diameter of 250mm while portion BC is 2m in length and section diameter of 100mm.The beam is subjected to a sudden tensile load.if the maximum stress induced is 400MN/m^2.Determine the strain energy stored in the beam.Take E=200GN/m^2
I need help on this question: a) Find the value of the maximum bending moment in the beam. The answer should be in kNm to three decimal places. b) Finds the maximum normal stress in the cross-section of the beam. Enter the positve value of the stress. The answer should be in MPa to two decimal places.