Which option is not a recommended technique for dispensing liquid from a micropipette into another solution? Select one: Place the tip slightly below the level of the solution before dispensing. Dispense the liquid along the inside of the glassware. Submerge the micropipette tip completely into the solution before dispensing. Hold the micropipette at a 45 degree angle when dispensing

Which option is not a recommended technique for dispensing liquid from a micropipette into another solution? Select one: Place the tip slightly below the level of the solution before dispensing. Dispense the liquid along the inside of the glassware. Submerge the micropipette tip completely into the solution before dispensing. Hold the micropipette at a 45 degree angle when dispensing

Chemistry: The Molecular Science

5th Edition

ISBN:9781285199047

Author:John W. Moore, Conrad L. Stanitski

Publisher:John W. Moore, Conrad L. Stanitski

Chapter13: The Chemistry Of Solutes And Solutions

Section: Chapter Questions

Problem 83QRT

See similar textbooks

Similar questions

The recommended patient dose for cisplatin is 20.0 mg/m². For an adult male patient with a body surface area of 1.90 m², determine the correct drip rate to deliver this dose of a 1.00 mg/mL IV solution in 2.50 hours through microdrip tubing with a drop factor of 60.0 gtt/mL. (1 drop = 1 gtt)
Filtration of samples A, B, and C show no residue left. After letting them dry in different beakers, SAmple A remains no residues. Sample B shows crystal leftovers, and sample C show brown film on the beaker walls. This means that: a. Two or more samples are heterogenous b. Two or more samples are homogenous c. all sample have 2 or more phases d. all samples are pure
Describe a procedure "fix" to solve the following recrystallization problems: A. No crystals are formed when the solution reaches room temperature. B. Colored impurities are present. C. Crystals are left on the filter paper during gravity filtration.
The efflux time of glycerin sample is 320 seconds having a density of 1.26 grams per mL. This is based on the room temperature setting. Water is used as a standard with the computed efflux time of 225 seconds having a density of 0.997 grams per mL. Viscosity of water was identified as 0.7202 CP. What is the viscosity of glycerin?
What filtration method would you use to separate the organic layer from the drying agent? Group of answer choices Centrifugation Gravity filtration Vacuum filtration
1. Minimal OR Maximum 2. Impurities OR substances while Impurities OR substance remain… 3. Centrifuge OR Filter
vacuum filtration uses suction to speed up the filtration process?
Volumetric pipettes are designed to deliver a precise amount of liquid, but only if you a. submerge the end of the pipette into a solution you are delivering. b. allow the pipette to drain freely, and leave any residual solution in the pipette. c. hold the pipette at a 45 degree angle and ensure that all the liquid is delivered.
In a warm environment, which restorative wax is recommended for surface restoration? a. opaque b. wouund filler c. lip wax d. medium consistency
Which of the following are safe and effective techniques for drying organic solids recovered from a filtration? (Choose all that apply). a. Spreading the solid evenly on a watch glass or aluminum weigh boat and placing it in an oven set at a temperature 20 °C below the substance's expected melting point. b. Placing it on top of a hotplate set on low. c. Leaving the solid on the funnel with the vacuum on for several minutes. d. Blowing on the solid.
Chemistry 1) Take 1 mL of a liquid bacterial culture (aka original culture) and mix it with 9 mL of uninoculated liquid medium in tube A.Take 0.1 mL from tube A and mix it with 9.9 mL of uninoculated medium in tube B.Take 0.2 mL from tube B and mix it with 99.8 mL of uninoculated medium in tube C.Take 0.05 mL from tube C and mix it with 19.95 mL of uninoculated medium in tube D. Take 0.25 mL from tube D and mix it with 99.75 mL of uninoculated medium in tube E. - If the original culture density were 3 x 107 cfu/mL, how many cfu would there be in 20 μL of dilution tube C? 2) If the absorbance (420 nm) of a 2 mL cell suspension is 0.28 absorbance units, and the cells are dried down to give 0.58 mg dry weight, and a typical cell is 2.9 x 10-13 g dry weight, what was the original density of the culture (in cells/mL)?
You have an impurity that is SOLUBLE in hot and cold water. A hot filtration is required. True False