Answered: While the pressure inside the piston-…

While the pressure inside the piston- cylinder device remains constant and 100 psig, the volume of air changes from 60,000 in3 to 35,000 in3. What is the work done in kN-m?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Related questions

Q: The volume of the passenger compartment of an aircraft is 2100 m³. A piece of automatic equipment…

Q: Pressure cooker containing air at STP has been heated and after sometimes, it was observed that the…

Q: A 180-lbm man has a total foot imprint area of 68 in2. Determine the pressure this man exerts on…

A: (a) The weight of the man is written as, The area of the total footprint is written as, The…

Q: A 1.2-m-diameter, 3-m-high sealed vertical cylinder is completely filled with gasoline whose density…

A: To proceed the following assumptions are taken into consideration 1)The Liquid in the container acts…

Q: Argon in the amount of 1.5 kg fills a 0.04-m3 piston-cylinder device at 550 kPa. The piston is now…

Q: A piston-cylinder assembly contains air at 210 kPa and occupies a volume of 0.0o1m'. The piston is…

Q: (a) A 3-kg plastic tank that has a volume of 0.2 m³ is filled with liquid water. Assuming the…

A: Given that the volume of the plastic tank=0.2m3, That is filled with water, water has…

Q: A gas is contained in a vertical, frictionless piston– cylinder device. The piston has a mass of…

Q: A vertical piston-cylinder device contains a gas at a pressure of 105 kPa absolute. The piston has a…

A: Given , pressure of the gas P=105kPaPressure inside the cylinder by gas is balanced by the local…

Q: Determine the energy needed to accelerate an 800-kg car from rest to 100 kph.

A: Given data: u=0 m/sv=100 km/h=27.78 m/sm=800 kg Need to determine the energy required.

Q: What happened to the surface tension of liquid when the temperature increase ?

A: The surface tension is depends upon the intermolecular force.

Q: A soap bubble with a diameter of 2.28" is to be enlarged by blowing air into it. If the surface…

Q: In a system similar to that shown in this image, the gas in the cylinder is at a pressure equal to…

A: It is the very basic question of thermodynamics. In which used concept is work done by a gas in a…

Q: 2) Nitrogen is contained in a vertical, frictionless piston-cylinder device. The piston has a mass…

A: Given mass of piston =3.6 kg diameter =16.5 cm =0.165 m F = 100 N P(atm)=88 kPa

Q: man weighing 180 Ibf is pushing a cart that weighs 100 lbf with its contents up ramp that is…

Q: Determine the volume of rigid tank if contains 50 kg of saturated liquid water at 90°C. * O 0.0718…

A: The steam exits in three phases:- Saturated Liquid Saturated Steam Supersaturated steam

Q: Determine the internal energy of water at 20 psia and 400°F.

A: Given data: Pressure, P = 20 psia Temperature, T = 400°F

Q: A cylinder is heated to cause a piston to move upwards using the expansion of gas inside it. If the…

Q: Q2: A gas is contained in a vertical, frictionless piston-cylinder device. The piston has a mass of…

A: Sol:-According to the given dataweight of the piston, W=3.2X9.81=31.392NForce exerted by sprintg,…

Q: Define pressure in a liquid at rest increases linearly with distance from the free surface.

A: Consider a small body submerged in water. Consider the cross-section area of body is dA. Assume a…

Q: gas is contained in a vertical, frictionless piston– cylinder device. The piston has a mass of 3.2…

A: Given Atmospheric pressure, Patm = 95 kPa Mass, m = 3.2 kg…

Q: A man weighing 180 lbf is pushing a cart that weighs 100 lbf with its contents up a ramp that is…

A: Given data: Wm=180 lbfWC=100 lbfθ=10°L=100 ft Need to determine required work for the man and the…

Q: An unknown composition of gas has undergone a compression process in a piston-cylinder assembly. The…

Q: The barometer of a mountain hiker reads 980 mbars at the beginning of a hiking trip and 790 mbars at…

A: Given data as per the question Pressure measured at the beginning =980 mbar Pressure measured at the…

Q: 1 m 2.5 m

A: Calculated combined weight of container and water.

Q: The pressure of a gas in piston-cylinder varies with volume according to PV=C. The initial pressure…

Q: 2.5 kW of solar energy comes on top of the solar panel placed on the roof of a house. 25% of this…

Q: A manometer containing oil (p = 850 kg/m3) is attached to a tank filled with air. If the oil-level…

A: As per given question Density of oil =850 kg/m3 oil level difference =80 cm Atmosphere pressure =98…

Q: Can someone explain why it became this? Why it necessary to use it? what is this? i dont get it.

Q: A 10 ft3 vessel of hydrogen at a pressure of 305 psia is vigorously stirred by paddles until the…

Q: A piston has area of5 cm?. What effort must the piston have if it exerts a pressure of 150 kPa on…

Q: Determine the specific volume of refrigerant -134a at a temperature of 5°C and a quality of 70%.

Q: Nitrogen at 500K and 200 kPa absolute is enclosed in a cylinder fitted with a frictionless piston.…

Q: Q1) Water is placed in a piston-cylinder device at 0,4 MPa and 85°C. Determine the work does the…

Q: A 4-m-diameter vertical cylindrical milk tank rotates at a constant rate of 15 rpm. If the pressure…

A: Angular velocity of the cylinder is calculated as, ω=2πN60=2π×1560=1.5 rad/s The equation of height…

Q: A glass tube is attached to a water pipe, as shown in the figure. If the water pressure at the…

Q: Note: 1 Torr 0.133 kPa & 1 atm = 101.325 kPa ) A spray metal bottle is used for polishing some…

Q: Q2: The water in a tank is pressurized by air, and the pressure is measured by a multi fluid…

A: Given data as per the question The density of oil =850 kg/m3 Density of mercury =13600 kg/m3 h1 =…

Q: Given an atmospheric pressure of 16.5 psia and an absolute pressure of 30.5 in. Hg, make these…

A: Given data: PAtm=16.5 psiaPAbs=30.5 in Hg Need to determine the pressures in psia, Pa and in of Hg.

Q: Determine the pressure at points A and B in the figure shown if the density of mercury is 13 590.0…

A: It is required to determine pressure at point A and B

Q: 3. A vertical frictionless piston cylinder contains air at a pressure of 300 KPa with atmospheric…

Q: A vertical, frictionless piston-cylinder assembly is filled with gas. The piston has a mass of 3.2…

Q: While the pressure inside the piston-cylinder device remains constant and 100 psig, the volume of…

Q: The Diameters of a small piston and a large piston of a hydraulic jack are 5 cm ad 10 cm…

A: The load lifted by the large piston: 1. When the piston are at the same level: 320 kN. 2. When…

Q: 2. An aerostat balloon is filled with hydrogen. It has a volume of 1000m3 at constant air…

A: The Answer is Below

Q: A tank is filled with oil whose density is ρ = 850 kg/m3. If the volume of the tank is V = 2 m3,…

A: Given Data density =850 Kg/m2 volume = 2m3

Q: 1- Which of the following is not the intensive property: a- Pressure. b- Temperature. c- Heat. d-…

A: (1) The pressure is an intensive property because it is the force which is divided by area and area…

Q: When the pressure on a given mass of liquid is increased from 3.0 MPa to 3.5 MPa, the density of the…

A: Given, Initial pressure = P = 3 MPa Final pressure = P' = 3.5 MPa Initial density = ρ = 500 kg/m3…

Q: A man is pushing a cart that weighs 100 lbf with its contents up a ramp that is inclined at an angle…

A: Given data:

Concept explainers

Thermodynamic Relations

Thermodynamics is the division of physics that deals with the transfer of any kind of energy, whether it be heat, temperature, or work, from one object to another.

Question

While the pressure inside the piston-
cylinder device remains constant and
100 psig, the volume of air changes
from 60,000 in to 35,000 in³. What
is the work done in kN-m?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

At a constant pressure, how does a volume of gas vary with respect to the absolute temperature?
A gas is contained in a vertical, frictionless piston– cylinder device. The piston has a mass of 3.2 kg and a cross-sectional area of 35 cm2. A compressed spring above the piston exerts a force of 150 N on the piston. If the atmospheric pressure is 95 kPa, determine the pressure inside the cylinder.
A piston-cylinder assembly with a total volume of 0.1546m3contains 1 kg of water at 350°C.The apparatus was cooled to a temperature of 100 °C.Calculate the final pressure of the water in kPa and its volume in m3.
Q2: A gas is contained in a vertical, frictionless piston-cylinder device. The piston has a mass of 3.2 kg and a cross-sectional area of 35 cm2. A compressed spring above the piston exerts a force of 150 N on the piston. If the atmospheric pressure is 95 kPa, determine the pressure inside the cylinder.
A gas is contained in a vertical, frictionless piston cylinder device. The piston has a mass of 2 kg and a crosssectional area of 35 cm2. A compressed spring above the piston exerts a force of 68 N on the piston. If the atmospheric pressure is 90 kPa, determine the pressure inside the cylinder in kPa
The container is partially filled with oil, water, and air. Determine the pressures at A, B, and C. Take density of water to be 1000 kg/m3, and density of oil to be 830 kg/m3. *The answer should be (A. 22.44 kPa, B. 7.725 kPa,C. 12.63 kPa)*
a 3m diameter vertical cylindrical tank rotates at a constant rate of 12rpm.if the pressure at the center of the bottom surface is 130kPa, determine the pressure at the edge of the bottom surface of the tank in kPa. take the density of the milk to be 1030kg/m^3
A piston-cylinder assembly contains air at 210 kPa and occupies a volume of 0.01m. Thepiston is attached to one end of a spring and the other end of the spring is fixed to a wall. Theforce exerted by the spring on the piston is proportional to the decrease in the length of thespring. The ambient atmospheric pressure is 100 kPa. Now, the air in the cylinder is heated tillthe volume is doubled and at this instant it is found that the pressure of the air in the cylinderis 600 kPa. Sketch the process on p-v diagram and calculate work done by the gas.
Both a gage and a manometer are attached to a gas tank to measure its pressure. If the reading on the pressure gage is 65 kPa, determine the distance between the two fluid levels of the manometer if the fluid is (a) mercury (? = 13,600 kg/m3) or (b) water (? =1000kg/m3).
A 1.2-m-diameter, 3-m-high sealed vertical cylinder is completely filled with gasoline whose density is 740 kg/m3. The tank is now rotated about its vertical axis at a rate of 70 rpm. Determine (a) the difference between the pressures at the centers of the bottom and top surfaces and (b) the difference between the pressures at the center and the edge of the bottom surface.
A vertical frictionless piston cylinder contains air at a pressure of 300 KPa with atmospheric pressure of 100 KPa. The diameter of the piston is 0.25m, and g = 9.8m/s2. Determine the piston’s mass.
A 4.5 m-diameter vertical cylindrical milk tank rotates at a constant rate of 15 rpm. If the pressure at the center of the bottom surface is 140 kPa, determine the pressure at the edge of the bottom surface of the tank. Take the density of the milk to be 1100 kg/m3. Draw the FBD