BuyFind

Welding: Principles and Applicatio...

8th Edition
Larry Jeffus
Publisher: Cengage Learning
ISBN: 9781305494695
BuyFind

Welding: Principles and Applicatio...

8th Edition
Larry Jeffus
Publisher: Cengage Learning
ISBN: 9781305494695

Solutions

Chapter
Section
Chapter 25, Problem 1R
Textbook Problem

Why are all welds not inspected to the same level or standard?

Expert Solution
To determine

The reason all welds are not inspected to the same level or standard.

Answer to Problem 1R

The quality of the weld that will pass or be acceptable for one welding application may not meet the needs of another.

Explanation of Solution

Given Information:

All welds are not inspected to same level or standard.

All welds are not inspected to the same level. The required quality of welds depends on the service which the object provides.

A high-quality weld is required in nuclear reactors, while a moderate quality of weld may work for house window.

So, the inspection of welds for nuclear reactor should higher the standards, but same standard for welds of house window will not be needed. Therefore, all the welds are not inspected to the same level or standard, rather it depends on the service of the object.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Get Solutions

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Get Solutions

Chapter 25 Solutions

Welding: Principles and Applications (MindTap Course List)
Show all chapter solutions
Ch. 25 - What are inclusions, and how are they caused?Ch. 25 - When does inadequate joint penetration usually...Ch. 25 - How can a notch cause incomplete fusion?Ch. 25 - How can an arc strike appear on a guided-bend...Ch. 25 - What is overlap?Ch. 25 - What is undercut?Ch. 25 - What causes crater cracks?Ch. 25 - What is underfill?Ch. 25 - What is the difference between a lamination and a...Ch. 25 - How can stress be reduced through a plate's...Ch. 25 - What would be the tensile strength in pounds per...Ch. 25 - What would be the elongation for a specimen for...Ch. 25 - How are the results of a stress test reported?Ch. 25 - What would be the transverse shear strength per...Ch. 25 - What would be the longitudinal shearing strength...Ch. 25 - What are the three methods of destructive testing...Ch. 25 - How are the specimens bent for a guided-. root-,...Ch. 25 - How wide should a specimen be if the material...Ch. 25 - Why are guidelines drawn on the surface of a...Ch. 25 - What part of a fillet weld break test is examined?Ch. 25 - What can happen if acids are handled carelessly?Ch. 25 - What information about the weld does an impact...Ch. 25 - Which nondestructive test is most commonly used?Ch. 25 - List the five steps to be followed when using a...Ch. 25 - What properties must metal have before it can be...Ch. 25 - Why will some flaws appear larger on an X-ray than...Ch. 25 - How is the size of a flaw determined using...Ch. 25 - What is the major limitation of eddy current...Ch. 25 - What information does a hardness test reveal?Ch. 25 - Why is it important to select the correct welding...

Additional Engineering Textbook Solutions

Find more solutions based on key concepts
Show solutions
Describe how to measure main bearing oil clearance.

Automotive Technology: A Systems Approach (MindTap Course List)

What are two reasons why a hole may need to be countersunk?

Precision Machining Technology (MindTap Course List)

What is a negative feedback loop? How is it used to keep a project in control?

Principles of Information Security (MindTap Course List)

Visit a hardware store and obtain information on the standard sizes of the following items. a. Screws b. Plywoo...

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

What is the difference between a vulnerability and an exploit?

Network+ Guide to Networks (MindTap Course List)

When you post digital content online, it is a good idea to tag it so that it is easy to locate and organize.

Enhanced Discovering Computers 2017 (Shelly Cashman Series) (MindTap Course List)

Convert 5 megawatts of power into BTU/hr, ft-lbs/s, and kJ/hr.

Fundamentals of Chemical Engineering Thermodynamics (MindTap Course List)

If your motherboard supports ECC DDR3 memory, can you substitute non-ECC DDR3 memory?

A+ Guide to Hardware (Standalone Book) (MindTap Course List)