Why do we need to use bus bar protection? Generalise the theory behind it

Q: What is a receptacle?  What is meant by “service drop”? What are sets of service-entrance…

A: As per the guidelines given, we can only provide the solution of one question in multiple type of…

Q: Calculate the values of the parameters ?1 and ?2 in order for the closed-loop system, whose block…

A:

Q: What are the poles according to their duties?

A: The function of poles is to support the conductors. poles should be capable to carry the load due to…

Q: What are the methods you will suggest to improve the commutation problems?

A: There are mainly four methods to improve commutation. (I) Resistance commutation. (ii) Voltage…

Q: What does matched load mean?What happens if the load is not matched?

A: In this question, we will define matched load..

Q: .Analyze and Comparison of Voltages at PQ bus and PV bus. 1. At the PQ bus, the value of voltage is…

A: The first step in the analysis is the suitable equations for the power flows in the system. The…

Q: Why is CMRR dimensionless?

A: Common-mode rejection ratio (CMRR) is the ratio of the common-mode gain to differential-mode gain.

Q: Derive Denavit-Hartenberg representation of Forward Kinematic equations of Robots with right…

A: Explanation:   A commonly used convention for selecting frames of reference in robotic applications…

Q: 1. List out how does a priority method varies from dynamic programming method in Unit commitment…

A: NOTE: We’ll answer the first question since the exact one wasn’t specified. Please submit a new…

Q: What Are The Different Dimensions Of The Terms Engineering And Management?

A:

Q: 1) The Bus Interface Unit (BIU) construction?

A: according to guidelines, we need to solve only first question.

Q: Describe the effect of the step size on the slope overload phenomena?

A: Slope overload phenomenon happens when the slope of the input signal is greater than the delta…

Q: 2. What is Commutation in DC Machines? What are the methods you will suggest to improve the…

A: COMMUTATION IN DC MACHINES: A DC generator's armature generates an alternating voltage when it is…

Q: Full introduction of Flexible AC transmission System (FACT) devices with illustrations

A: AC transmission System (FACT) devices : AC transmission System (FACT) devices is a system which…

Q: LOOK! THINK! DO! WORKPLACE HAZARD/ACCIDENT What is the Can the hazard OHS strategy? hazard? harm…

A:

Q: Q5) Define the types of the communication systems forms and plot them and explain each one in…

A: (5) Communication System: a. It is a system that allows information to be exchanged between two…

Q: What are the advantages of root locus method?

A: The Root locus is define as locus of closed loop pole when system gain K is vary from zero to…

Q: You have an underground buried cable, suppose the cable is defected (open circuit) somewhere along…

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: 2. What is meant by open and short concept in cabling?

A: When a potential is applied across the ends of a conductor (wire or cable), the circuit becomes…

Q: Explain the Scalar Control Method used in VFDSS.

A: To analyse the scalar control method used in VFDs

Q: How equation is obtained ? is that equation given in the textbook ?

A: That equation is the direct formula of pulse spread. And no need of derivation of the equation.…

Q: Discuss the importance of safety in an engineering maintenance from Kasapreku’s case scenario?

A: Answer:  The food and beverages industries has a moral and regulatory obligation to keep the work…

Q: Q4: Define the types of the communication systems forms and plot them and explain each one in…

A: Communication System : It is a system in which exchange the information between two node or points.…

Q: Why is there a need for matching in telecommunication systems? What is the purpose of matching?

A: Telecommunication systems are a mode of communication with each other. it includes local, as well as…

Q: Explain the computational procedure of load flow by "fast decoupled load flow" method

A: Fast decoupled load flow method - ALGORITHM- Step 1: Assume a suitable solution for all buses…

Q: Discuss the adaptive relaying philosophy in power system protection.

A:

Q: Each item below describes key characteristics of a particular system (that is, a plant transfer…

A: Hi! Thank you for the question. I am solving the Question for 3 sub-parts Part (a) to Part (c) as…

Q: Describe the ultimate cycle method, including the satisfactory perfor- mance. Also briefly discuss…

A: For system the maximum slope line starts at its origin , the delay is identified as the time at…

Q: t are the factors that affect the slope overload phenomena?

A: Slope overload phenomenon occurs in Delta modulation.  In Delta modulation (DM), the analog input…

Q: Which stability is called as load stability? Why it is called like that?

A: Under the normal conditions, after the system is subjected to a disturbance the ability of a power…

Q: . What is “accessible” as applied to wiring methods? What is “accessible” as applied to equipment?…

A: In an electrical system, there are various terms which are used for different phenomenon and gives a…

Q: 1. Define the following about Systems:  a. What is used to describe or determine a black box…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: 1-Draw the structure of single bus bar system

A: In this question we will draw structure of single bus bar system.... Note:- as per our guidelines, I…

Q: How can you understand the zones of protection CTs and PTs And their applications in Protection…

A: Current transformers are generally used to measure currents of high magnitude. These transformers…

Q: What precautions are practiced by electric companies in terms of loading capacity? When is a…

A: The precautions are practiced by electric companies are given as: Avoid water while operating with…

Q: What are the causes of short circuits? What are the effects of short circuit in to electrical…

A: Short circuit is an abnormal condition and occurs rarely. Short circuit occurs when there is a low…

Q: a) What do you mean by adaptive protection? What functions are expected to be performed by an…

A: Adaptive protection The given protection utilizes settings for adjustable protective relay(ex-…

Q: hat is “Voltage collapse”? Why does voltage instability occur? What are the countermeasures to deal…

A: Voltage collapse is the process in which the voltage at significant part of the power system becomes…

Q: What is ampere circuital law?

A: This law gives the relation between the magnetic field and the current which created the magnetic…

Q: What is Commutation in DC Machines? What are the methods you will suggest to improve the commutation…

A: COMMUTATION IN DC MACHINES: When a DC generator's armature is put in a rotating magnetic field, it…

Q: Question 6: Though many electronics students and professionals alike associate semiconductor…

A: similarities between electromagnetic relays and semiconductor logic gate    1.  semiconductor gate…

Q: Example: show the control signals needed to perform Add R1, R2, RO using: a. Three bus organization…

A:

Q: What are sets of service-entrance conductors?

A: Since three questions are present and nothing is mentioned, as per the guidelines, in the following…

Q: briefly describe the steps involved in the newton raphson method

A: Newton raphson method

Q: What are some of the significant rules used by technicians who want to follow the smart money and…

A: The technician's responsibilities include monitoring and servicing systems, diagnosing problems and…

Q: Explain how can improve cellular system capacity in details?

A: Cellular system : A cellular system is the connection of multiple networks that consists a large…

Q: Explain the term concurrent engineering. Why is itimportant?

A: Concurrent engineering means that the manufacturing process and the products are designed…