par Tomat. A section of a reinforced concrete elevator shaft is shown in the figure. Compute the following: a. Centroid of section; b. Centroidal Moments of Inertia; and 4 c. Rigidity about the centroidal axes. Consider the effect of shear deflection. Assume h = 15m, P = 500 kN, and fc = 24 MPa. 1.12 1.12 2022, 18:00 0.40 3.24 2.83

Q: Q-3 The frame shown in Fig. 3 is fixed at A, E and pinned at D. Analyse the frame for the given…

A:

Q: Four forces are exerted on the eyebolt as shown. If the net effect on the bolt is a direct pull of…

A: Component of each force in X and Y direction can be shown below Along Y axis component forces are…

Q: What error in horizontal angles is consistent with the following linear precisions?1>5000,…

A: 1  rad =206,248.8"(a) 15000×206,248.8"=41.25"(b) 120,000×206,248.8"=10.31"

Q: Determine and plot the tensions in cable segments AC and BC as a function of x over

A:

Q: If X liters per second of water flows through the system shown below, calculate the total headloss…

A:

Q: Water is pumped through a 600 mm diameter circular pipe which is 1800 meters long at the velocity of…

A:

Q: Calculate the second moment of area for a 50 mm ×100 mm stud with the actual dimensions shown on…

A: Given:- The dimension of the stud = 50 mm × 100 mm  The actual dimension of the stud = 45 mm × 105…

Q: Q3:-The uniform 10 kg ladder in figure below rests against the smooth wall at B, and the end A rests…

A: For the ladder in the given figure,  Given the weight of the ladder, W = 10 kg length of the ladder…

Q: HW For the beam shown in figure, find the deflection and rotation at Free end by using double…

A:

Q: The absolute specific gravity of a soil sample with the saturated unit weight and dry unit weight…

A: given- saturated unit weight γsat=20 kN/m3dry unit weight γd= 15.69 kN/m3moisture content w=22%void…

Q: 20 kN A B 30 kN/m F 16 kN D C 2m 4m 4m 3m Which of the following most nearly gives the reaction (KN)…

A: Asked: To determine the reaction at the roller support.   The reaction at the roller support (C) can…

Q: Please help me Provide a design schedule using Microsoft schedule indicating the stages of…

A: The Various stages of Constructing a One-story Concrete house are as follows:- (1) Pre-Construction…

Q: Q.14. The velocity of flow in a badly corroded 7.5 cm pipe is found to increase 20% as a Pinot tube…

A: Let assume the flow as turbulent ; uu' = 2.5 loge yε + 8.5 where ; u = Velocity at y u ' =…

Q: the lightest rectangular beam

A: Step -1 In this question we have to find Height (h) of lightest rectangular beam and let width of…

Q: Q3. A solid shaft was made of alloy steel, it was welded to a flat plate by a specific size of…

A:

Q: The tension member shown in Fig.3 is a PL 1/2 x 8 of A36 steel. The member is connected to a gusset…

A: Given data:- For grade A 36, FY=36 ksiFu=58 ksit=0.5 inw=8 in Dead load =95 kips Live load =9 kips

Q: The object is fired vertically upward from the ground, with an initial velocity of 50 m/s. The mass…

A: Given that,  initial velocity = 50 m/s mass of the object = 10 kgs atmospheric resistance FD= 105 N…

Q: A static center-point bending test was performed on a 50 X50 X760 mm wood sample according to ASTM…

A: Given data:- Length of span, L=710 mm Maximum load, w=2.67 kN Width of beam, b=50 mm Depth of beam,…

Q: The combined action of the three forces on the base at O may be obtained by establishing their…

A: Given Data:Assume:F1=320lbF2=500lbF3=580lba=6.9ftb=3.6ftc=2.3ftθ=42°.

Q: Given the direction and values of reactions at hinge and roller of the beam shown in the figure.…

A:

Q: For the simply supported beam shown. Find the maximum bending moment from :the bending moment…

A:

Q: The force P is applied at d = 50 mm from the bottom as shown. Compute the normal stress at section…

A: Given: The value of d is 50 mm. The value of P is 85 kN. Consider the figure,

Q: Compute an actual dimension of a distance if the given drawing measurement in the plan is 28 cm…

A: Map scale  A distance on a map and its corresponding distance on the planet are related by a scale.…

Q: the deflection curve of the simply supported beam of Fig. 8-7 subject to the uniformly distributed…

A:

Q: The can in the given image floats in the position shown. The diameter of the can is 19 cm. What is…

A: Asked: To determine the weight of the can shown floating in the given figure.   Given: Diameter of…

Q: Air flows through a pipe at a rate of 200 L/s. The pipe consists of two sections of diameters 20 cm…

A:

Q: Softwood advantages and disadvantages.

A: As the name suggests, softwoods are soft in nature and light in weight, which have gained much more…

Q: The total horizontal and vertical stresses at a point X in a saturated sandy medium are 170 kPa and…

A:

Q: Which of the following most nearly the total degree of indeterminacy? 1 O O N 3

A:

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6…

A:

Q: A helical spring is composed of 20 turns of 22 mm - diameter wire on a mean radius of 100 mm. Use G…

A:

Q: Task: Solve for the reactions . . • Let the force of one of the E member be equal to P.". (interior…

A: To determine reactions :                                        ∑FX=0HA+15 = 0HA = -15 KN∑FY=0RA +…

Q: The concrete column (300 mm 300 mm) is reinforced by four steel bars each having diameter of 30 mm…

A: Find the value of P?

Q: Q5: A 50m*30m site has 1 m thick layer of organic soil, to be replaced with granular fill (G-2.6)…

A: The given data is shown below: Size of site=50m×30mDepth=1mGs=2.6Fines=21%Oversized…

Q: Which below situation provides the smallest bearing capacity for soil under a square footing (width…

A:

Q: Le Lo + The steel structure is loaded as shown. hc = 4 m, Lb = 3m, P = 40 KN, E = 200 GPa, I = Ic=…

A: Since C is a roller support hence can't provide  horizontal reaction(HC =0) against the load But it…

Q: A typical aluminum-alloy scuba diving tank is shown. The outside diameter of the tank is 200 mm and…

A:

Q: Q6: The figure represents a homogeneous earth dam with a horizontal filter. The construction cost…

A: The equation of Parabola,                                            x2+y2 = x+y Let , BC' =…

Q: Use the provided data wherever you need. Q1. A (25 kW, 500 rpm) motor has a mild steel shaft of (30…

A: Given Revolutions per minute = 500

Q: having span of 100 m, dip "h" load of 25 kN/m. Find the chang 61080

A:

Q: Compute the allowable capacity of axially loaded compression steel column in kN as shown having a…

A: Let's find out the moment of inertia of the section The section is symmetric about x axis and Y…

Q: Cantilever beam loaded as shown in fig., draw the shear force diagram and bending moment diagram. 20…

A: Consider the figure,

Q: Find the flow rate in m'/sec/m at right angles to the cross section shown through the permeable soil…

A:

Q: The bar, WA= 100 [lb] and L=3 [ft], shown in figure is initially in the vertical position. The bar…

A: Given :

Q: An effective rainfall of 2-hour duration produced a flood hydrograph peak of 200 m³/s. The flood…

A:

Q: Problem 01: An object is fired vertically upward from the ground, with an initial velocity of 50…

A:

Q: For a cylindrical pressure vessel, the normal stress comp longitudinal section is known as O Axial…

A: The normal stress component on a longitudinal section is known as longitudinal stress. It is tensile…

Q: 1. Event: A large landslide occurred in a mountain hillside near a large, populated city in a sunny…

A: The main reasons behind the landslide are : Road construction on hill slope making it unstable  and…

Q: Which of the following is NOT TRUE as an assumption in the elastic analysis of circular members…

A: Asked: To choose the incorrect assumption corresponding to elastic analysis of circular members…

Q: Q-1: Determine the resultant force at pins A, B and C on the three member frame. 800 N С 200 N/m 2m…

A: length of member AC = 2sin 600= 2.31 m load on member AC = 200 x 2.31 =462 N horizontal component =…

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.