Write the AC mesh current equations for the following circuit. There is one independent current source and one independent voltage source. Assume the sources have the same frequency of 10° rad/sec and zero phase shift. Put the equations in matrix form. Do not attempt to solve

Write the AC mesh current equations for the following circuit. There is one independent current source and one independent voltage source. Assume the sources have the same frequency of 10° rad/sec and zero phase shift. Put the equations in matrix form. Do not attempt to solve

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.2P: Convert the following instantaneous currents to phasors, using cos(t) as the reference. Give your...

See similar textbooks

Related questions

Q: In a three-phase system, the per-unit symmetrical components of the phase currents are IO = 0.5 , I9…

Q: A three phase system cannot be obtained using two single phase source.

A: given two single phases source we need to obtain 3 phase source

Q: The three conductors a 3 - phase overhead line are arranged in a horizontal plane, 4 meters apart.…

A: Solution: According to the given condition, the diagram is as follows:

Q: The line with symmetrical spacing then the equilateral spacing (Deq) for the three-phase…

A: The line with symmetrical spacing then the equilateral spacing (Deq) for the three-phase inductance…

Q: For the circuit shown in figure, draw the oriented graph and write (i) tieset matrix, (b) cutest…

Q: Derive the relation of SWR in terms of ZL (load impedance) and Zo (Characteristic impedance)

Q: The load's impedance is Zload = A 13.2-kV single-phase generator supplies power to a load through a…

A: Given: A 13.2-kV single-phase generator supplies power to a load through a transmission line. The…

Q: 6. Magnitude of line voltages is V3 times the magnitude of phase voltages V= V3 V,, what Phasor…

A: For star connection, Line voltage = sqrt(3)×phase voltage. Given VL =sqrt(3)×Vp. So we will draw…

Q: Gauss-Elimination Method [Q1] Using Nodal or Loop Analysis, determine the currents I1, I2, and Iz…

A: Since there are multiple questions present and you have not specified which question to answer,…

Q: The currents flowing in the lines toward a balanced load connected in A are Ia 10020° A, I, =…

A: Given line currents are, Ia = 100∠0° AIb = 141.4∠225° AIc = 100∠90° A

Q: In the three-phase system shown in the figure, phase a is on no load and phases b and C are…

Q: (a) Give THREE (3) advantages of a three-phase system compared to a single-phase system.

Q: Van = 330&angle;510°, Vbn = 330&angle;270°, Vcn = 330&angle;390°" A POSITIVE PHASE SEQUENCE B…

A: Conversion formula

Q: The national standard phase sequence in oman is R B Y Select one: True False

A: The national standard phase sequence in Oman is R B Y this statement is true.

Q: Q2/The Double circuit 3-phase overhead transmission line has spacing as shown in the figure below.…

A: In this power system, Find the value of inductance L in per km We know inductance L= 2×10-7…

Q: Consider the network given in figure below, where the numbers indicate admittances in per unit. Find…

Q: 1. For each of the three single-phase transformers below, the phase pos voltage has been drawn on…

A: According to question: The phasor diagram is drawn by assuming that the turn ratio of each…

Q: A 10 km long three phase line having a diameter of 2.5 mm conductors is arranged symmetrically with…

Q: n A Three-phase transposed line is composed of one conductor per phase with flat horizontal spacing…

Q: Give example problems for impedances and admittance.

Q: A three phase system with one conductor per phase as shown in the figure. The conductors are…

Q: In a three phase overhead system , each line is suspended by a string of three insulator. The…

Q: A Three-phase transposed line is composed of one conductor per phase with flat horizontal spacing of…

Q: 1. In a 3-phase overhead system, each line is suspended by a string of 3 insulators. The voltage…

A: Given voltage across top and middle units, using this we will find Ratio of capacitance, string…

Q: 2. Solve for the line currents, phase currents and the total complex power absorbs by the loads.

A: It is given that:

Q: Determine the node voltages after one iteration for the single-phase lateral shown in the figure.

Q: solve for: 1. Source phase voltages 2. Source line voltages 3. Line currents

A: To solve for 1) Source phase voltages 2) Source line voltages 3) Line currents

Q: Q: Prove that the capacitance of 3-ph overhead line (with the effect of ground) is given by: 2πε Cn…

A: Solution- Effect of earth on capacitance- The method of images is used to determine the capacitance.…

Q: (a) The line currents in amperes in phases a, b and c respectively are 500 + j150, /100 - j500 ånd…

Q: Balanced 3-phase Delta connected voltage sources are given in the figure. Find the star-connected…

A: The delta star transformation is done to simplify the circuits. The line voltage in star connection…

Q: Q: Prove that the capacitance of 3-ph overhead line (with the effect of ground) is given by: 2πε Cn…

A: Capacitance- Capacitance is dependent on the ratio of Q and V and independent of the individual…

Q: B- Two 1-phase furnaces a and b are supplied at 80V by means of a Scott-connected transforme…

A: A Scott connected transformer is used for producing a two phase electrical circuit from a three…

Q: Suppose that a current source with Is amperes of current is connected in parallel to a pair of…

A: This is a basic problem of circuit. The solution is given in the next step.

Q: A single phase line has resistance of 5Ω per conductor and inductance of 25 mH per conductor. The…

Q: Q9-b) Sketch the connection of 3-phase source to 3-phase load using 3–phase 4 wire complete with…

Q: In a three phase overhead system, each line is suspended by a string of three insulator. The…

A: In a three phase overhead system, each line is suspended by a string of three insulator. The…

Q: Can you explain the theory behind why the inductor in phase R and phase B become in series when…

A: As, the given circuit is Currently the inductors are in star connection and they are supplied with…

Q: 7. In the circuit below write the loop equations and set up (not solve) the matrix equation for the…

Q: What are the types of connections in three phase load, which connection is best? Justify your…

A: Four types of connection we have for three phase transformer- Y-Y- This is used for small, H.V.…

Q: A three-phase 50 Hz double circuit as shown below, assumed that the line is completely trasposed.…

A: Given transmission line circuit is 3-phase double circuit. Diameter of each conductor is 2.76 cm.…

Q: Determine Relation between Line Current and Phase Currents in delta-delta connection

A: In a balanced system the three phase currents are equal in magnitude and are displaced from one…

Q: Select one: O a. Phase and line currents are not equ O b. Phase current is zero O C. Phase and line…

A: There are two types of connections in three phase system. They are 1. Star 2. Delta.

Q: Q1/Use nodal voltage method, find the magnitude and direction of * .current I

Q: PROBLEMS : 1. The IR drop in the line due to the reactive current is one disadvantage of low power…

A: In this question we will write why low power factor loads are undesirable....

Q: 91/ Form bus impedance matrix [Z I for bus the power system shown be lous.

A: Fig: Given power system

Q: Given the circuit shown below, if Zx = 100<0degrees determine the current in each branch using NODAL…

A: NOTE: Unit of Zx is not given. we assumed it as ohm. We assumed nodes and current directions on the…

Q: A three-phase 50 Hz double circuit as shown below, assumed that the line is completely trasposed.…

A: Given in the question: Distance between the conductors, D = 6m = 0.06cm Radius of the conductor, r =…

Q: Solve the following circuit using Gauss Elimination method, V/R=1; R R V

A: The cycle of line decrease utilizes rudimentary column tasks and can be divided into two sections.…

Q: Expression for a voltage reflection co-efficient in terms of load impedance and characteristics…

Concept explainers

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors. The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.

Question

please show all the steps.

5) Write the AC mesh current equations for the following circuit. There is one independent
current source and one independent voltage source. Assume the sources have the same
frequency of 106 rad/sec and zero phase shift. Put the equations in matrix form. Do not
attempt to solve
8 mH
la
2A
10NF
15 Ohm
10 Ohm
+
20V
3 la
1 mH
100 Ohm
2nF

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1nf to f

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The circuit shown in the figure is in the frequency (phasor) plane.showing the environmental current equations in the simplestShow in the figure [Z] [I] = [V]?Here [Z] impedance matrix, [I], [V] respectivelyis the vector of current and voltage.
Problem 6: Suppose the voltage source for a series RL-circuit were given as V0sin(ωt) instead of V0cos(ωt). Part (a) Enter an expression for the current amplitude in terms of V0, ω, R, and L. I0 = ______ Part (b) Calculate the current amplitude, in milliamperes, when V0 = 1.9 V, ω = 45 rad/s, R = 29 Ω, and L = 0.84 H. I0 = ______ Part (c) Enter an expression for the tangent of the phase constant in terms of ω, R, and L. tanφ = ______ Part (d) Calculate the phase constant, in radians in the range -π/2 ≤ φ ≤ π/2, for the circuit parameter values given in part (b). φ = ______
The line with symmetrical spacing then the equilateral spacing (Deq) for the three-phase inductance calculation is D12=D23=D31=D. Select one: True False
NOTE: Polar form for Voltage & Current. Rectangular form for Impedance Find the total impedance of the circuit, total power (apparent) delivered by the current source, Draw the phasor diagram of the voltage and current at the source, the current passing through the R2 and L1 branch, Draw the phasor diagram of the voltage and current at the R2 and L1 branch. Also, is the circuit inductive, capacitive, or neither (resistive)?
Explain current divider rule in ac circuits with two parallel impedances Z1 and Z2. Calculate the currents I1 and I2 in phasor form for the circuit given in figure.
Find out the zero-phase sequence components of the following set of three unbalanced voltage vectors: Va =10cis30° ,Vb= 30cis-60°, Vc=15cis145°" (THIS PROBLEM IS MULTIPLE CHOICE PLEASEE CHOOSE A LETTER BELOW AND PROVIDE YOUR CLEAR SOLUTION!) A 16.809cis-72.579° B 5.603cis72.579° C 16.809cis-47.421° D 5.603cis-47.421°
Using the node-voltage method, determine the magnitude of the phasor voltage V1; that is, find |V1| in Volts (peak). The values of the phasor voltage sources in the above diagram are VA = 3 and VB = 3 Volts. The resistor values are R1 = 4 Ω and R2 = 8 Ω, and X1 = 12 for the capacitor giving an impedance of -j12 Ω. Express your answer using 3 significant figures.
ZL impedance for maximum average power transfer in the circuit shown in Figure 2and find the value of the maximum average power transferred to the ZL? (Can you write the steps in detail in sentences?)
Find the following: the power drawn by the 100ohm variable resistor If the variable resistor is set to 200-ohms, instead of 100-ohms, What is the power drawn by the 200-ohms resistor? total current of the system Is the circuit inductive, capacitive, or neither (resistive)? NOTE: Polar form for Voltage & Current. Rectangular form for Impedance
Given the circuit shown below, if Zx = 100/0 o determine the current in each branch by: a) Nodal Methodb) Maxwell’sMethod
Find out the zero-phase sequence components of the following set of three unbalanced voltage vectors: Va =10cis30° ,Vb= 30cis-60°, Vc=15cis145°" (THOS PROBLEM IS MULTIPLE CHOICE PLEASEE CHOOSE THE LETTER WITH THE CORRECT ANSWER AND PLEASE PROVIDE YOUR CLEAR SOLUTION! A 16.809cis-72.579° B 5.603cis72.579° C 16.809cis-47.421° D 5.603cis-47.421°
Two alternating voltage are given by v1 = 120 sinωt volts and v2 = 200 sin(ωt – π/4) volts. Obtain sinusoidal expressions for v1 + v2 . (a) by plotting waveforms, and (b) by vector. Please show some graph and diagram on how you solve this problem ?