In a three phase overhead system , each line is suspended by a string of three insulator. The voltages across top unit and the middle unit are 8KV and 11KV respectively. Calculate a) ratio of shunt capacitance to self capacitance b) line voltage c) string efficiency

In a three phase overhead system , each line is suspended by a string of three insulator. The voltages across top unit and the middle unit are 8KV and 11KV respectively. Calculate a) ratio of shunt capacitance to self capacitance b) line voltage c) string efficiency

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter8: Symmetrical Components

Section: Chapter Questions

Problem 8.25P

See similar textbooks

Related questions

Q: Each line of a 3-phase system is suspended by a string of 3 similar insulators. If the voltage…

A: given voltage across string unit=17.5kv no of insulator=3 shunt capacitance 1/10 th of the…

Q: Three single-phase two-winding transformers, each rated 400 MVA, 13.8/ 199.2 kV, with leakage…

Q: A 70-kV, three-phase short .Determine t

A: It is given that: V= 70 kVL=18 KmZphase=1+j5 ΩPR3-ϕ=90 MW

Q: Write an introduction about: LOAD BALANCING in 3-Phase System

A: Three-Phase System - A three-phase system is formed out of a three-phase voltage source that is…

Q: In a three phase overhead system , each line is suspended by a string of three insulator. The…

Q: In a three phase overhead system, each line is suspended by a string of three insulator. The voltage…

Q: The positive-sequence reactances for the power system shown below are in per unit on a common MVA…

A: As per the guidelines of Bartley we supposed to answer first three subparts of the question for…

Q: A three-phase, wye-connected, 7 kVA, 230 V synchronous generator has a reactance of 7 ohms per…

A: Base impedance=Voltagecurrent =Voltagecurrent×voltageVoltage…

Q: The positive-sequence reactances for the power system shown below are in per unit on a common MVA…

A: It is given that:

Q: Generators generate positive sequence voltage only False True

A: Positive Sequence: The positive sequence is a three-phase balanced system in which the system has…

Q: The value of value of voltage measured in residential convenience outlet is average voltage. True…

A: Average value is the average of the signal over the period of time. Where as rms value of the signal…

Q: A single-line diagram of a three-phase balanced system is given below. A bolted three- phase short…

Q: 1.2 For each set of voltages, state whether or not the mCE voltages form a balanced three-phase set.…

A: The explanation is as folows.

Q: Q1// a three-phase, 60Hz, 500 MWVA, 15kV, 32 pole hydroelectric generating unit has an H constant of…

A: (a) ωs=2πf Plugging the known values, f=60 Hzωs=2πfωs=2π×60 radsωs=377 rads ωsm=2Pωs Plugging the…

Q: From the system as shown below with base of 100 MVA by neglecting all parallel admittance. (a)…

A: I am considering that given values are impedances and Iam calculating the diagonal and off diagonal…

Q: A single-line diagram of a three-phase balanced system is given below. All the motors are rated with…

Q: In a Gauss-Seidal method of power flow studies,the network of 4 bus system consists of 6 equations…

A: We need to tell about G S method

Q: In a power system having three conductors A, B and C of a 3-phase line carrying currents IA, IB and…

A: The three-phase line is represented by the phase A, B, and C, the current across the given conductor…

Q: The real and reactive powers scheduled at load buses are variable True False

A: We need to tell about real and reactive schedule power .

Q: Example 1 A three-phase, wye-connected system is rated at 50MVA and 120kV. Express 40MVA of three-…

Q: In a three phase overhead system, each line is suspended by a string of three insulalor. The voltage…

Q: Draw an impedance diagram for the electric power system shown in Figure 3 showing all impedances in…

A: The equivalent circuit of a power system is the impedance diagram, in which the various components…

Q: 2_ What case/cases in which the measured phase current include the three symmetrical components (…

Q: In an unbalanced three phase system, having balanced supply phase voltages are separated by 120°…

A: The objective is to determine the correct option.

Q: In a 3-phase overhead system, each line is suspended by a string of 3 insulators. The voltage across…

A: Given three phase overhead system , each line is suspended by a string of 3 insulators The voltage…

Q: 2) For a given short-circuit calculation utilizing the per unit method, a base voltage of 480 V and…

A: Given, Base voltage, Vb=480 V Base power, Sb=2500 kVA

Q: A 4.16 kV three-phase feeder is supplying a purely resistive load of 5400 kVA. It has been deter-…

A: The solution can be achieved as follows.

Q: In a three phase overhead system , each line is suspended by a string of three insulators. The…

A: Given V1=8 kV V2=11 kV m=CshCsat V2=V1(1+m)(1+m)=V2V1=118=1.3751+m=1.375m=1.375-1…

Q: A transposed overhead transmission line has self-reactance (X;) and mutual reactance (Xm) as 0.5…

A: Given, A transposed overhead transmission line has, Self reactance, Xs=0.5 ohmkm Mutual reactance,…

Q: The base current and base voltage of a 345-kV system are chosen to be 3000 A and 300 kV,…

A: Given: Base current =3000 A Base Voltage=300 KV Actual value =345 KV

Q: Figure 6.12 shows the one-line diagram of a simple three-bus power system with generators at buses 1…

Q: Explain the following items i) Steps used to draw the equivalent impedance diagram of the network…

A: i) Procedure to draw impedance diagram 1. Establish Base Voltage through the System 2. Calculate the…

Q: The real and reactive power of slack bus are determined after the power flow analysis. Select one:…

A: There are three types of bus in power system, namely, Slack bus Generation bus Load bus

Q: In a three phase overhead system, each line is suspended by a string of three insulator. The…

A: In a three phase overhead system, each line is suspended by a string of three insulator. The…

Q: In a Gauss-Seidal method of power flow studies,the network of 4 bus system consists of 6 equations…

A: From the load flows in power system

Q: a short three phase transmission line with the importance of 5 + jade 20 into ohm per face has…

A: Assuming the power factor to be 0.8 lagging because it seems that there is a typo while mentioning…

Q: A single-phase transmission line 30 kV, 60 Hz, 100 kVA, consists of two hard-drawn aluminium…

Q: Each line of a 3-phase system is suspended by a string of 3 similar insulators. If the voltage…

Q: what is the Analysis of 3 Phase star connected circuit? please write introduction

A: Power systems include source and load at sending and receiving respectively. Three-phase sources and…

Q: Apply the knowledge of per unit system on above network and draw an impedance diagram showing all…

A: For the given data impedance diagram is drawn as shown below

Q: 2- The Purpose of using Unbalanced Three-phase Systems:

A: The purpose of using unbalanced three phase system is

Q: 5) Non minimum phase systems are also non causal. True False

A: Non-minimum Phase system: They are causal and stable systems whose inverse are causal but unstable.…

Q: positive sequence components having phase sequence the same as the * .original phasors true false…

A: The positive sequence is, The three sets of phasors are equal in magnitude in the positive sequence…

Q: The bus impedance matrix for a three-bus power system has per-unit elements as: Z11 = 0.5 Z12 = 0.4…

A: In this question we need to find a subtransient fault current when a 3 phase fault occur at bus 3.

Q: In a 3-phase overhead system, each line is suspended by a string of 3 insulators. The voltage across…

A: Given three phase overhead system , each line is suspended by a string of 3 insulators The voltage…

Q: The % voltage drop is calculated for 3-phase systems by taking phase quantities and per phase line…

A: Percentage voltages drop is calculated for both per phase quantities as well as three phase…

Q: In a 3-phase Overhead System, each line is suspended by a string of 3 Insulators. The voltage across…

A: Given voltage across top and middle units, using this we will find Ratio of capacitance, string…

Q: Calculate the per unit voltage drop on the transmission line e) Calculate also the sending end…

Q: Athree-phase, wye-connected, 6.25 kVA, 220 V synchronous generatorhas a reactance of 8.4 N perphase.…

A: The given system is a three-phase Y connected, the base values are as follows: Vbase=220…

Concept explainers

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Single Phase and Three Phase System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the bus admittance matrix (Ybus) for the three-phase power system shown in Figure 6.23 with input data given in Table 6.11 and partial results in Table 6.12. Assume a three-phase 100 MVA per unit base. TABLE 6.11 Bus input data for Problem 6.20 TABLE 6.12 Partially Completed Bus Admittance Matrix (Ybus) for Problem 6.30
Consider a single-phase electric system shown in Figure 3.33. Transformers are rated as follows: XY15MVA,13.8/138kV, leakage reactance 10 YZ15MVA,138/69kV, leakage reactance 8 With the base in circuit Y chosen as 15MVA,138kV determine the per-unit impedance of the 500 resistive load in circuit Z, referred to circuits Z, Y, and X. Neglecting magnetizing currents, transformer resistances, and line impedances, draw the impedance diagram in per unit.
Considering two parallel three-phase circuits that are close together, when calculating the equivalent series-impedance and shunt-admittance matrices, mutual inductive and capacitive couplings between the two circuits can be neglected. True False
The following parameters are based on a preliminary line design: per unitVS=1.0, VR=0.9 per unit, =5000km,Zc=320,=36.8. A three-phase power of 700 MW is to be transmitted to a substation located 315 km from the source of power. (a) Determine a nominal voltage level for the three-phase transmission line, based on the practical line-loadability equation. (b) For the voltage level obtained in part (a), determine the theoretical maximum power that can be transferred by the line.
In a balanced three-phase Y-connected system with a positive-sequence source, the line-to-line voltages are 3 times the line-to-neutral voltages and lend by 30. (a) True (b) False
PowerWorid Simulator case Problem 3_60 duplicates Example 3.13 except that a resistance term of 0.06 per unit has been added to the transformer and 0.05 per unit to the transmission line. Since the system is no longer lossless, a field showing the real power losses has also been added to the oneline. With the LTC tap fixed at 1.05, plot the real power losses as the phase shift angle is varied from 10 to +10 degrees. What value of phase shift minimizes the system losses?
Consider the single-Line diagram of a power system shown in Figure 3.42 with equipment ratings given: Generator G1: 50MVA,13.2kV,x=0.15p.u. Generator G2: 20MVA,13.8kV,x=0.15p.u. Three-phase -Y transformer T1: 80MVA,13.2/165YkV,X=0.1p.u. Three-phase Y- transformer T2: 40MVA,165Y/13.8kV,X=0.1p.u. Load: 40MVA,0.8PFlagging,operatingat150kV Choose a base of 100 MVA for the system and 132-kV base in the transmission-line circuit. Let the load be modeled as a parallel combination of resistance and inductance. Neglect transformer phase shifts. Draw a per-phase equivalent circuit of the system showing all impedances in per unit.
Figure 3.39 shows a oneline diagram of a system in which the three-phase generator is rated 300 MVA, 20 kV with a subtransient reactance of 0.2 per unit and with its neutral grounded through a 0.4- reactor. The transmission line is 64km long with a cries reactance of 0.5-/km. The three-phase transformer T1 is rated 350MVA.230/20kV with a leakage reactance of 0.1 per unit. Transformer T2 is composed of three single-phase transformers, each rated 100 MVA, 127/13.2kV with a leakage reactance of 0.1 per unit. Two 13.2kV motors M1 and M2 with a subtransient reactance of 0.2 per unit for each motor represent the load. M1 has a rated input of 200 MVA with its neutral grounded through a 0.4- current-limiting reactor, M2 has a rated input of 100 MVA with its neutral not connected to ground. Neglect phase shifts associated with the transformers. Choose the generator rating as base in the generator circuit and draw the positive-sequence reactance diagram showing all reactances in per unit.
A Y-connected load bank with a three-phase rating of 500 kVA and 2300 V consists of three identical resistors of 10.58. The load bank has the following applied voltages: Vab=184082.8,Vbc=276041.4, and Vca=2300180V. Determine the symmetrical components of (a) the line-to-line voltages Vab0,Vab1, and Vab2, (b) the line-to-neutral voltages and Van0,Van1, and Van2, (c) and the line currents Ia0,Ia1, and Ia2. (Note that the absence of a neutral connection means that zero-sequence currents are not present.)
For large power transformers rated more than 500 kVA, the winding resistances, which are small compared with the leakage reactances, can often be neglected. (a) True (b) False
A 60-Hz, single-phase two-wire overhead line has solid cylindrical copper conductors with a 1.5 cm diameter. The conductors are arranged in a horizontal configuration with 0.5 m spacing. Calculate in mH/km (a) the inductance of each conductor due to internal flux linkages only, (b) the inductance of each conductor due to both internal and external flux linkages, and (c) the total inductance of the line.