You are asked to design a square steel bar out of ASTM A36 steel. The steel has yield strength of 250MPA (page480). The square steel bar is subjected to a tensile load of 50KN. Your client has asked you to have a safety factor of 3 for your design. Determine the required size of the steel rod (side length of the square cross section).

You are asked to design a square steel bar out of ASTM A36 steel. The steel has yield strength of 250MPA (page480). The square steel bar is subjected to a tensile load of 50KN. Your client has asked you to have a safety factor of 3 for your design. Determine the required size of the steel rod (side length of the square cross section).

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.5P: A steel pad supporting heavy machinery rests on Four short, hollow, cast iron piers (see figure)....

See similar textbooks

Similar questions

A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?
A steel pad supporting heavy machinery rests on Four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression in 50 ksi. The outer diameter of the piers is d = 4.5 in, and the wall thickness is t = 0.40 in. Using a factor of safety of 3.5 with respect to the ultimate strength, determine the total load P that can be supported by the pad.
You are given a square rod of 6061-T6 aluminum (cross-section = 4mm X 4mm, length = 2.3m). The material has a Young’s modulus of 72 GPa. If a tensile load of 3 kN is applied to the ends of the rod (parallel to the 2.3m dimension), what is the applied engineering normal stress?
A tensile-testing apparatus is to be constructed that must withstand a maximum load of 293516 N. The design calls for two cylindrical support posts, each of which is to support half of the maximum load; the minimum yield and tensile strengths of this alloy are 343 MPa and 565 MPa or 82,000 psi respectively.what is required diameter? Take factor of safety is 2.3
What will be the minimum diameter of a steel wire, which is used to raise a load of 4000N if the stress in the rod is not to exceed 95 MN/m²?
You are given a square rod of 6061-T6 aluminum (cross-section = 4mm X 4mm, length = 2.3m). The material has a Young’s modulus of 72 GPa. If a tensile load of 3 kN is applied parallel to the 2.3m dimension, what is the change in length of the rod?
(a) Briefly explain why the Tresca yield criterion will result in a more conservative (safer) design than that based on von Mises criterion.(b) A cast alloy structure, ABCD is bolted at its base, A and carries a load of 235 N at end D, as shown in Figure Q1. The diameter of the structure is 20 mm. Take the yield strength of the alloy at 70 MPa:(i) Determine the stress acting in the material of the structure at point B. Draw the stress element and indicate the stress values.(ii) Determine if this stress state would cause yielding of the material by calculating the factor of safety using both the Tresca and von Mises yield criterion.(iii) Draw the loci of both yield criteria in the principal stress axes and indicate the stress state of part (ii) on the plot.
See the set of bars for made of a material that has a yield strength of 350 MPa, determine the minimum h1 and h2 dimensions required. Apply a safety factor F.S. = 1.5 without flow. Each bar is 12 mm thick
3. A cylindrical metal rod of 50mm diameter and 3m length is subjected to a tensile load of 150KN. To what length the cylinder should be centrally bored on one side to reduce weight by material removal, so that the total extension will increase by 20 percent under the same pull. The diameter of the hole being bored on one side is equal to 25mm. Take E= 200GPa.
.A 5-mm thick mild steel plate is used to form a hollow column of 60 mm outside diameter. The column length is 1.2 m. Calculate the crippling load using Johnson’s Parabolic formula. Take modulus of elasticity and yield strength as 206 GPa and 330 MPa, respectively. Assume one end is hinged and the other end fixed.218212 N176745 N930094 N263252 N
To support a tensile load of 65 kN, a circular cross section and A metallic rod with a length of 0.32 m will be used. Stress in bar 240 MPa value and maximum elongation is desired to be 0.42 mm. In these conditions, at least What is the (minimum) rod diameter [m]?(Elasticity for metallic bar Take the module as 220 GPa).
A tensile-testing apparatus is to be constructed that must withstand a maximum load of 293516 N. The design calls for two cylindrical support posts, each of which is to support half of the maximum load. Furthermore, plain-carbon(1045) steel ground and polished shafting rounds are to be used; the minimum yield and tensile strengths of this alloy are 343 MPa and 565 MPa(82,000 psi), respectively. Specify a suitable diameter in mm for these support posts. Assume safety level is 2.3. Round your answer to 2 significant figures.