You are given a square rod of 6061-T6 aluminum (cross-section = 4mm X 4mm, length = 2.3m). The material has a Young’s modulus of 72 GPa. If a tensile load of 3 kN is applied parallel to the 2.3m dimension, what is the change in length of the rod?

You are given a square rod of 6061-T6 aluminum (cross-section = 4mm X 4mm, length = 2.3m). The material has a Young’s modulus of 72 GPa. If a tensile load of 3 kN is applied parallel to the 2.3m dimension, what is the change in length of the rod?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.7P: Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and...

See similar textbooks

Related questions

Q: A hollow cylindrical rod with a diameter of 100mm and a thickness of x tensile load of 12.5 kN. Find…

A: Given data:

Q: A tensile test is performed on a brass specimen10 mm in diameter using a gage length of 50 mm(see…

A: Consider a bar having cross-sectional area A, length L and Young's Modulus E is subjected to load P.…

Q: Calculate the extension of the bar (△L).

A: Calculate the extension of the bar (△L)

Q: . A sheet of plywood consists of three equally thick sheets, the upper and lower sheets having their…

A: Given Tensile modulus, E1 = 10 GPa E2 = 0.4 GPa Find Tensile…

Q: The cylindrical rod BC, diameter 3.6 mm made of steel supports the AD bar with a distribution of…

A: Given data dBC=3.6mm E=200 GPa

Q: An AISI 1020 steel rod 22 feet long is anchored between two rigid supports. At 90 degrees Fahrenheit…

A: For AISI 1020 steel rod, E=29000 ksi=29×106 psi and α=6.5×10-6 in/in.°F. Let Ti be the initial…

Q: a. A metal thickness 16mm and having a rectangular cross-section carries a load of 60KN. Find the…

Q: 1. Label all points of significance on the stress strain curve 2. Draw the stress-strain curve for…

A: **According to the guidelines we can answer only three sub parts of a question, please resubmit the…

Q: Question 3: Find the extension in mild steel wire of 10 mm in diameter and 1.6 m long, the wire is…

A: Given, Diameter of the steel wire = d = 10 mm Length of the wire = 1.6 m = 1600 mm Axial load on the…

Q: ny mm is the smallest allowable outer diameter of the washer

A: GIVEN :- Diameter of rod : d= 34mm washer inner diameter : di = 37.5 Allowable stress of rod : σ=…

Q: 2.76 Steel railroad rails 10 m long are laid with end-to-end clearance of 3 mm at a temperature of…

Q: A rod 150 cm long and diameter 2.0 cm is subjected to an axial pull of 20 kN. If modulus of…

A: As per given question Given data Rod length =150cm Diameters =2.0cm Axial pull =20 kn Modulus of…

Q: Problem Solving: Show your Solution 1. A sculpture weighing 10,000 N rests on a horizontal surface…

A: 1) Weight of sculpture =10000 N h=6 m A=0.20 m2 density =2700 kg/m3 length of segment =3 m

Q: 5. The following tensile test specimen is tested for loading in uniaxial tension as shown in figure…

A: Given : To find: curve if the sample is in elastic limit

Q: The structure shown in Figure 3.1 consists of bar BD and two rods, AD and CD. Assuming that the…

A: Draw the given diagram showing the axes and specifying B as the origin. From the figure, taking B…

Q: A solid cylindrical bar is subjected to tensile test. The initial diameter of the bar is 60 mm. The…

Q: Q6. A 2.25 m long solid bar (Lo) with a 32 mm diameter is placed under tension by a load (F) of 250…

A: GIVEN DATA- F=250KN L=2.25m D=32mm E=200GPa WE HAVE TO FIND CHANGE IN LENGTH

Q: A 12-mm thick steel tire has a width of 110 mm and internal diameter of 800 mm. It is heated and…

Q: You are in charge of designing a new fixture for a “universal testing machine” that will attach a…

A: The data given is, Maximum load = 30 kN Maximum permissible shear stress, σ = 600 Mpa To…

Q: 3. A cylindrical metal rod of 50mm diameter and 3m length is subjected to a tensile load of 150KN.…

A: Strain is the deformation in the material per unit length. True strain is the natural log of the…

Q: 3. A mild steel rod supports a tensile load of 50 kN. If the stress in the rod is limited to 100…

A: Given Data: Tensile load, P=50 kN Stress, σ=100 MPa

Q: A test specimen in a tensile test has a gage length of 2.0 in and an area = 0.5 in?. During the test…

A: Given data, Gage Length (L1) = 2 in Area (A) = 0.5 in 2 Load (P) = 32,000 lb, when gage length…

Q: Find the pull force P that will make the total elongation of the system 0.04 mm. b) Calculate the…

Q: Determine the total deformation of the steel rod shown in figure (1) under the given loads. Take the…

Q: (Q.3) Ni cylindrical specimen having an elastic modulus of 207 GPa and an original diameter of 1.02…

Q: If the length and diameter of a material is 25 cm and 10 mm respectively. Then find the elongation…

A: Given : load, W =750*103N length, L=250mm diameter,d =10mm Area,A =π/4*d2 =78.53 mm2 young modulus ,…

Q: 3. A wrought iron rod is under a compressive load of 350 kN. If the permissible stress for the…

A: We are suppose to solve only one question. Please post other question as a separate question. For…

Q: 1. A brass rod of diameter 25 mm and length 250 mm is subjected to a tensile load of 50 kN and the…

Q: In the system given in the figure, the rods are identical and it is desired to be produced in the…

Q: QUESTION 3: Square profile made of hollow 1045 steel, with a length of 6 meters with a…

A: Given data: Cross-section of Square hollow profile of steel pipe is drawn below. Cross-sectional…

Q: The structure below is made from stock (same stock for A-B-C and B-D) that is 5 mm thick (into the…

A: Given: The structure is made up of stock (same stock for A-B-C and B-D). 5 mm thick. b mm wide.…

Q: Q.3 A flat plate of width 60mm has a central hole of 10mm diameter. This plate is subjected to an…

A: Given data, Load of F= P kN =1000P N Width w= 60 mm Diameter of hole = d= 10 mm σyp= 300 MPa…

Q: stanchion and carries a vertical load of 50 kN. Assuming that the total shearing stress in a bolt is…

A: GIVEN:

Q: Question 2 A rod, which tapers uniformly from 40 mm diameter to 20 mm diameter in a length of 400 mm…

Q: A steel bar is initially 250 mm in length with a square cross-section of 50 50 mm. The modulus of…

A: load applied along the length will cause longitudinal stress and strain longitudinal stress will…

Q: Question Two A steel flat of thickness 10 mm tapers uniformly from 60 mm at one end to 40 mm at…

A: To find : The percentage error Given : The thickness of steel flat plate is t=10 mm. The taper…

Q: A column is made from a rectangular bar whose cross section is 5.1 cm by 8.7 cm. If the height of…

Q: The cable of hoist has a cross sectional of 80mm2.The hoist is used to lift a crate weighining 500…

A: Given Area, A = 80mm2 Load, P = 500 kg Length, L = 30 m Find 1. stress on the cable 2.…

Q: 2-6. Nylon strips are fused to glass plates. When moderately heated the nylon will become soft while…

Q: A spherical pressure vessel 400-mm in diameter has a uniform thickness of 6 mm. The vessel contain…

A: To Find : The Factor of safety with respect to tensile failure . Given : The diameter is D=400 mm.…

Q: Q2: A spacer is turned from Aluminum alloy with elasticity modulus of 78 GN/m². The spacer has a…

A: Given Data Modulus of spacer is : E=78 GN/m2=78000 N/mm2 Diameter of spacer is : d=28 mm Length of…

Q: The following figure shows the critical position of a crane that supports 2.5 Tons of load by means…

A: (a) Start by calculating the rest of the forces in the crane using equilibrium equations:…

Q: Problem 1: A steel rod with a cross-sectional area of 0.20 in² is stretched between two fixed…

A: Given data: The cross-section area is The 1st temperature is The tensile load is The 2nd…

Q: An aluminum wire of length 2.0 m and diameter 5 mm is used to hang a load of 100 kg. The modulus of…

Q: A steel wire 60cm long and 0.32 cm in -9 radius is attached to the pulley in 5.5cm radius , 3kg…

A: Given: The length of wire, L = 60 cm The radius of of wire, r = 0.32 cm The radius of pulley, R =…

Q: Question Two A steel flat of thickness 10 mm tapers uniformly from 60 mm at one end to 40 mm at…

A: “Since you have asked multiple questions, we will solve the one question for you. If you want any…

Q: 2 Figure 2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…

Q: 200 stress 150 (MPa) 100 50 0.1 0-2 strain From the tensile stress-strain behavior for the brass…

Q: Question 4 The bar in Figure is made of steel that is assumed to be elastic perfectly plastic, with…

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Properties of Engineering Materials

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
A round bar of 10 mm diameter is made of aluminum alloy 7075-T6 (see figure). When the bar is stretched by axial forces P, its diameter decreases by 0.0 16 mm. Find the magnitude of the load P. Obtain the material properties from Appendix 1.
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.