You are designing a mold to cast the solid part shown in the figure below from pure copper. If the runner diameter is 1 in and the molten copper velocity in the runner is 0.5 in/s. If the Chvorinov Constant is 50 S/in². Calculate the number of casts we can fill and solidify on a single sand mold in 1 shift = 8 hours duration? Part Dimensions in inches A=5 B=3 C=3 D=3 E=2 F= 2

You are designing a mold to cast the solid part shown in the figure below from pure copper. If the runner diameter is 1 in and the molten copper velocity in the runner is 0.5 in/s. If the Chvorinov Constant is 50 S/in². Calculate the number of casts we can fill and solidify on a single sand mold in 1 shift = 8 hours duration? Part Dimensions in inches A=5 B=3 C=3 D=3 E=2 F= 2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A sprue in a sand mould has a topdiameter of 20 mm and height of 200mm. The velocity of the molten metalat the entry of the sprue is 0.5 m/s.Assume acceleration due to gravity as9.8 m/s and neglect all losses. If themould is well ventilated, the velocity(upto 3 decimal points accuracy) of themolten metal at the bottom of the sprueis ______ m/s.
Determine the time required to fill the mold cavity along with the riser as shown in the following figure. A slab of 1500 mm x 750 mm x 500 mm is required to be cast using a sand casting process. It was observed previously that the total solidification time (T) for this casting = 1.6 min. Find out the cylindrical riser dimensions (diameter to height ratio = 1) for a solidification time T = 5 min.
A aluminium alloy casting has a cylindrical geometry with 100mm in diameter and weighs 3200 gram. This casting takes 7.5 min to completely solidify. Another smaller and lighter cylindrical-shaped casting with the same diameterto-length ratio weighs 1800 gram. This casting is made of the same aluminium alloy and the same conditions of mold and pouring were used. Determinea) The mold constant in Chvorinov’s Rule,b) The dimensions of the lighter castingc) The total soldification time of the lighter casting. The density of aluminium alloy= 2.7 gram/cm3and n=2
compute the diameter of the sphere (mm) that will freeze in the same time in same casting process with a 62.5mm x 150mm x 225mm plate. Assume that constant mold for this casting is 55 mm^2/s
For the casting of the part, whose perspective pictures are given below, take into account the surface of the section, the model design, if necessary, the core design, all the molding stages and finally the mold in the most suitable form for casting, and name all the mold elements by showing them on the figure (Note: The hole shown in the figure, full hole.)
The height of the down sprue is 175 mm and its CS are at the base is 200 mm² The CS area of the horizontal runner is also 200 mm² Assuming no losses, indicate the correct choice for the time (second) required to fill a mould cavity of volume 106 mm³ (Use g=10 m/s^ 2 )
Q1. A mold sprue is 20 cm long, and the cross-sectional area at its base is 2.5 cm2 .The sprue feeds a horizontal runner leading into a mold cavity whose volume is 1560 cm3. Determine:(A) velocity of the molten metal at the base of the sprue(B) volume rate of flow(C) time to fill the mold.
For the casting of the part whose perspective pictures are given below, take into account the surface of the section, the model design, if necessary, the core design, all the molding stages and finally, draw the mold in the most suitable form for casting and name all the mold elements by showing them on the figure (Note: The hole shown in the figure is a full hole. .)
Determine the time required to fill the mold cavity along with the riser as shown in the following figure.
1.L What is the difference between casting and forging process? Explain the three stages in casting process and its applications.
2. What are the general defects found in casting processes? Name and briefly describe two.
A vertical centrifugal casting process is used to produce bushings that are 0.2 m outside diameter and 0.2 m in long. If the rotational speed during solidification is 500 rpm, determine the inside diameter at the bottom of the bushing if the diameter at the top is 0.084 m. * Add file