You are presented with the following controlled rectifier configurations: |Configuration Topology Supply phase voltage Load resistance Load inductance (line to neutral) (Ohm) (Henry) |Single phase half-wave Single-phase bridge Three-phase half-wave Three-phase bridge Six-phase half-wave Vs 100 Vs Vs 100 3 100 4. Vs 100 Vs 100 infinite Assume no commutation diodes are used. State the smallest firing delay angle that will effect discontinuous current flow in the load for, 8. Configuration 4; 9. Configuration 5;

You are presented with the following controlled rectifier configurations: |Configuration Topology Supply phase voltage Load resistance Load inductance (line to neutral) (Ohm) (Henry) |Single phase half-wave Single-phase bridge Three-phase half-wave Three-phase bridge Six-phase half-wave Vs 100 Vs Vs 100 3 100 4. Vs 100 Vs 100 infinite Assume no commutation diodes are used. State the smallest firing delay angle that will effect discontinuous current flow in the load for, 8. Configuration 4; 9. Configuration 5;

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter19: Special-purpose Outlets-water Pump, Water Heater

Section19.2: Water Heater Branch Circuit

Problem 8R: For residential water heaters, the Consumer Product Safety Commission suggests a maximum temperature...

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
How is a solid-state diode tested? Explain.
What is CEMF?
Diodes and rectifiers allow current to _________. flow in one direction only flow in both directions divide paths of flow none of the above
For residential water heaters, the Consumer Product Safety Commission suggests a maximum temperature setting of ___________ F (_____________ C). Some states have laws stating a maximum temperature setting of ____________ F (________________ C).
Single phase Full wave controlled rectifier with inductive load connected tо 120 V source. The R load equal 10 ohm, the inductive is very large. If the delay angle equal 30 degree Calculate 1- average load voltage 2-average load current 3-maximum load current 4-RMS load current 5-power supplied to the load 6-Form factor 7-ripple factor 8-draw the voltage source, V load, I load, current in each diode
For a Full wave rectifier circuit, the AC voltage input to transformer primary is 115V. Transformer secondary voltage is 50V. Load resistor is 25 ohms. Determine Peak and Average DC Component of load voltage. (Assume ideal diodes) a.VDC (peak) = 25.4 V; VDC (average) = 18.5V b.VDC (peak) = 35.4 V; VDC (average) = 22.5V c.VDC (peak) = 38.4 V; VDC (average) = 23.5V d.VDC (peak) = 50 V; VDC (average) = 34.5V
Q1.Three-phase half wave rectifier supply resistive load with DC power of 4 kW; the ammeter connected with D1 indicates 8 A r.m.s current, and the source frequency is 50 Hz Due to system inductance the average voltage drops to 96.2% of idealized value ( when the inductance is neglected). How much will the average and r.m.s voltage s be? The r.m.s phase current and average load current Is=? & Idc=? The secondary r.m.s voltage and transformer capacity Vs & KVA? The inductances causes the voltage drop Lc=? The diode forward current and maximum inverse voltage? Now, if the phase B is failed ( disconnected), how much with new dc voltage be in %..Vdc=….% ??
A full-wave rectifier is connected to a single-phase source and supplying an inductive load. For the sake of simplicity, you can assume that the ripple at the output current is negligible. Input specifications: The source is single-phase utility grid at 220 V and 50 Hz. Output specifications: The load resistance is 10 Ohm. Sketch the schematic of the system. Sketch the waveforms of the output voltage and current and the source voltage and current. Determine all the performance parameters.
Three-phase half wave rectifier supply resistive load with DC power of 4 kW; the ammeter connected with D1 indicates 8 A r.m.s current, and the source frequency is 50 Hz Due to system inductance the average voltage drops to 96.2% of idealized value ( when the inductance is neglected). How much will the average and r.m.s voltage s be? The r.m.s phase current and average load current Is=? & Idc=? The secondary r.m.s voltage and transformer capacity Vs & KVA? The inductances causes the voltage drop Lc=? The diode forward current and maximum inverse voltage? Now, if the phase B is failed ( disconnected), how much with new dc voltage be in %..Vdc=….% ??
The primary winding to secondary winding turns ratio of a centre-tapped transformer is 5:1. The primary winding of the transformer is fed from 220V ac supply and the secondary voltage is connected to a single phase full wave rectifier which consist of two diodes. The forward resistance of each diode is 50 and load resistance is 250. Determine the following: A. peak value of current B. de load current C. rms value of load current D. de power E. ac power input to rectifier F. efficiency of rectifier
Draw the following rectifier circuits with an input voltage of 12 Vrms and an RL=2K. Determine the output voltage and the current in RL. Plot these waveforms indicating the peak values and the time as per calculation. Also solve for the output DC value. Use silicon diode/s in your analysis. Half wave rectifier circuit (include the diode voltage analysis), Full wave bridge rectifier circuit, Full wave rectifier using center tapped transformer