You are using a DC motor that has a stall torque of 1 Nm. The motor is rotating at 200 rpm. No-load speed is 400 rpm. The output of the DC motor is connected to a 12 tooth pinion, which is in mesh with a 36 tooth gear. Assuming 100% efficiency, what is the torque at the output shaft, when the motor is running at peak power? Enter your numerical answer assuming units of Nm.

You are using a DC motor that has a stall torque of 1 Nm. The motor is rotating at 200 rpm. No-load speed is 400 rpm. The output of the DC motor is connected to a 12 tooth pinion, which is in mesh with a 36 tooth gear. Assuming 100% efficiency, what is the torque at the output shaft, when the motor is running at peak power? Enter your numerical answer assuming units of Nm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A spur pinion of pitch diameter 50 mm rotates at 200 rad/s and transmits 3 kW power. The pressure angle of the tooth of the pinion is 20°. find the total force exerted by a tooth of the pinion on other gear?
Provide very clear and complete solution and diagam. SITUATIONAL PROBLEM: Two shafts are connected by spur gears. The pitch radii of the gears A and B are 200 mm and 860 mm respectively. If shaft A makes 350rpm and is subjected to twisting moment of 250 N-m. Pressure angle is 14.5 degree. What is: a.) Rpm of gear B b.) Torque in shaft B (in Newton meter). c.) Separation load of two gears (in newtons). d.) Total load on gears (in newtons).
Provide the complete step-by-step solution, given data, conversion of units, and sketch for this problem. A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000rpm. The gears are 20 degrees involute herringbone gears of 28 pitch and 2 1/8 ineffective width. The pinion has 20 teeth with a helix angle of 23 deg. Determine theload normal to the tooth surface. A. 20.4 lbs B. 24.4 lbs C. 28.4 lbs D. 32.4
Please answer part 2, A 20° full depth involute spur pinion of 4 mm module and 21 teeth is to transmit 15 kW at 960 rpm. Its face width is 25 mm. 1.The tangential force transmitted (in N) is (a) 3552 (b) 2611 (c) 1776 (d) 1305 2. Given that the tooth geometry factor is 0.32 and the combined effect of dynamic load and allied factors intensifying the stress is 1.5 the minimum allowable stress for the gear material in MPa is, (a) 242.0 (c) 121.0 (b) 166.5 (d) 74.0
A parallel helical gear set of 19 tooth pinion is driving a 57 tooth gear. The helix angle of 20 degrees while the normal pressure angle is 14.5 degrees and the normal diametral pitch of 10 teeth/inch. If the pinion is rotating at 1800rpm and transmits 50hp, find the normal force. Please answer in detailed solution.
For a pair of standard gears, the module is m=2.5mm，pressure angle is α=20 0. ha*=1. c*=0.25. The teeth number on gear 1 is z1=22. The standard center distance is a=68.75mm. Find the following parameters of gear 2: the teeth number, z2 = ( ) the diameter of reference circle, d2=( )mm the diameter of addendum circle da2 =( )mm the diameter of dedendum circle df2 =( )mm
n Mukwano Industries, a shaft assembly shown in Fig. 2 is driven by a flat belt at location A and drives a flat belt at location B. The drive belt pulley diameter is 300 mm; the driven belt pulley diameter is 500 mm. The distance between sheaves is 800 mm, and the distance from each sheave to the nearest bearing is 200 mm. The belts are horizontal and load the shaft in opposite directions. Determine the size of the shaft using Distortion Energy Theory (DET) and the types of steel that should be used. Use a safety factor of 10. Also, provide a free-body diagram as well as moment and torque diagrams
Suppose we have determined that the lowest natural frequency of a particular helical compression spring is 20286 rpm. According to the prescription in our book and according to the presentation in class, find the highest recommended operating frequency of a machine that utilizes this spring. Give your answer in rpm, but do not include units--Blackboard will not understand
The client requires a single step-up spur gearbox to transmit a 10 kW power from a shaft rotating at 1000 rpm, while the output speed must be 1700 rpm. The material for gear and pinion is 817M40 and 655M13, respectively. Use table 6.10 on page 128 to select the suitable gear and pinion. 1.1 Briefly state the problem. 1.2 State the design specification considering the following design factors: 1. Functionality 2. Stress 1.3 State formula and standards relevant to the single step-up spur gearbox design. 1.4 If the pinion has 20 teeth, use the Lewis formula to determine the face width of the pinion and gear. Then, do one set of calculations and tabulate the answers. 1.5 Conclusion.
A truck equipped with a 50 HP engine uses a roller chain as the final drive to the rear axle. The driving sprocket runs at 225 rpm with a center distance of approximately 500 fpm. The transmission efficiency between the engine and the driving sprocket is 85%. 1.1 Determine the pitch and width of chain to be used. 1.2 Determine the number of teeth in each sprocket and the pitch diameters.
the figure shows a motor driving a two-output transmission system. The blower requires a certain amount of force to operate since the drum rotates at an angular acceleration of 0.03 rad/s2. Determine the torque produced by a motor with a torque of 700 Nm and a speed of 1,600 rpm. following:- The power produced at the drum (P). The torque requirement for the blower to operate (Tblower) and power generation (Pblower) The overall efficiency transmission of the gear system, hO. If the speed of motor is NOT given, explain without calculation how the overall efficiency transmission of the gear system can be obtained. Given:- Number of gear teeth, t:- t1=40 ; t2=200 ; t3=50 ; t4=200 ; t5=40 ; t6=120 ; t7=60 and t8=120 Equivalent mass moment of inertia, Ieq:- Imotor,5=25 kgm2 ; I23=10 kgm2 ; Iblower,4=15 kgm2 ; I67=20 kgm2 and Idrum,8=60 kgm2 Friction torque in bearing, Fb:- A=F=25 Nm ; I=J =20 Nm ; B=C=G=H=5 Nm and D=E=10 Nm Efficiency of all gear mesh, ⴄ=85%
In a single-stage gearbox consisting of helical gear pairs, input speed ng= 900 rpm, input power P1=16 kW, the number of teeth of the pinion gear z1= 20, the number of teeth of the second gear wheel z2= 61. gear wheelmaterial is 20MnCr5, for this material: σem=230 N/mm2, pem=1500 N/mm2 and E= 2.1.105 N/mm2is (Helix angle: β=180; grip angle: α=200; factor of safety: S=1.5; form factor: Kfn=2.7; dynamic loadfactor: Kd=1.25; width factor: ψm=12; clutch ratio: ε = 1.6). (20p)a) Calculate the modulus of the gear pair.Module according to root fracture:(p1)Module according to tooth surface crushing:(p2)(Standard module values: 1 – 1.5 – 2 – 2.5 – 3 – 3.5 – 4 – 5 – 6 – 7 – 8 mm)b) Dimension the gears (Diameters of section circle, head circle and base circle, distance between axes). Pay attention the units