You can use the Folding Diagram to find Alias frequencies that arise when analogsignals are not sampled fast enough. Remember, digital sampling will cause aliasingif the sampled signal has frequencies higher than the Nyquist Frequency (which isone half the sampling frequency).4. Let's look at the situation of our 40 Hz signal sampled at 50 Hz. Follow thesteps below:4.03.83.63.43.23,02.8262.4sampledfrequencysampling ratealias frequencyfolding frequency22201.81.61.41.2000.2040.6LO1. What is the Nyquist (or Folding) Frequency for this situation?2. Divide the highest Frequency in the original incoming signal by the Nyquist(or Folding) Frequency: fa/f=3. Use the Folding Diagram to find the ratio of the Alias Frequency over theNyquist (or Folding) Frequency: fa/fs =4. Find the Alias Frequency: fa= (f/t) xfs=%3!5. Does this Alias Frequency match what you found before in 27

All physical signals are analog continuous time signals. To process such signals using computer or…

You can use the Folding Diagram to find Alias frequencies that arise when analog signals are not sampled fast enough. Remember, digital sampling will cause alliasing if the sampled signal has frequencies higher than the Nyquist Frequency ( which is one half the sampling frequency). 4. Let's look at the situation of our 40 Hz signal sampled at 50 Hz. Follow the steps below: 4.0 3.8 3.6 3.4 3.0 28 26 sampled frequency 22 sampling rate alias frequency 20 1.8 folding froqucncy 1.6 1.4 1.2 00 0.2 04 06 1O 1. What is the Nyquist (or Folding) Frequency for this situation? fy 2. Divide the highest Frequency in the original incoming signal by the Nyquist (or Folding) Frequency: fa/f 3. Use the Folding Diagram to find the ratio of the Alias Frequency over the Nyquist (or Folding) Frequency: f/= 4. Find the Alias Frequency: fa= (f/fi) x fs =_ S. Does this Alias Frequency match what you found before in 27

You can use the Folding Diagram to find Alias frequencies that arise when analog signals are not sampled fast enough. Remember, digital sampling will cause alliasing if the sampled signal has frequencies higher than the Nyquist Frequency ( which is one half the sampling frequency). 4. Let's look at the situation of our 40 Hz signal sampled at 50 Hz. Follow the steps below: 4.0 3.8 3.6 3.4 3.0 28 26 sampled frequency 22 sampling rate alias frequency 20 1.8 folding froqucncy 1.6 1.4 1.2 00 0.2 04 06 1O 1. What is the Nyquist (or Folding) Frequency for this situation? fy 2. Divide the highest Frequency in the original incoming signal by the Nyquist (or Folding) Frequency: fa/f 3. Use the Folding Diagram to find the ratio of the Alias Frequency over the Nyquist (or Folding) Frequency: f/= 4. Find the Alias Frequency: fa= (f/fi) x fs =_ S. Does this Alias Frequency match what you found before in 27

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

)A compact disc (CD) records audio signals digitally by using PCM. Assume the audio signal bandwidth to be 15 KHz, and the Quiantization level is 65536 a. What is the Nyquist rate? b. lf the Nyquist samples are quantized into L-65,536 levels and then binary coded, determine the number of binary digits required to encode a sample. c.Determine the number of binary digits per second (bits/s) required to encode the audio signal.
Question 1(Nyquist-Shannon sampling theorem.) Give detailed information about the Nyquist-Shannon sampling theorem. Explain what Aliasing is in the sampling theorem.
The power of a signal is 10 mW and the power of the noise is 1 μW; what are the values of SNR and SNRdB ?
Design a circuit using a Multiplexer, that has two inputs X, and S, where X represents an 8-bit BCD number,S is a sign bit. The circuit has one output Y, which is the Binary representation of thesigned-magnitude BCD number. A negative output is represented in the Binary 2’scomplement form.
Draw a 4-point DTF signal diagram for sequence x(n) with N = 4 samples. And explain the flow.
In the figure, a sampler is given as a modulator. From signal x (t) ? ∗ When passing to the (?) signal How do you choose the sampling period (T)? Explain.
Briefly explain the Nyquist theorem in the context of digital sampling.
1. What are the control methods for electromechanical systems. What arethe advantages of each method? 2. What are the design steps for a microcontroller basedelectromechanical system? 3. Given that sampling frequency (fs) is equal to 250Hz and Nyquistfrequency (fN) is equal to two times of the alias frequency, find the aliasfrequency. 4. You need to design a quantizer for a sensor which measures voltagevalues between 40 V and 200 V. If your resolution is 4 (n value) findthe number of output states (N) and quantization step (Q). 5. Design a capacitive transducer to be able to measure the displacementof a rotating element in a machine. Sketch the diagram and specifywhich parameters will let you measure the displacement.
Explain the Sampling Theorem and Nyquist Theorem. Give an example
An analog signal having a maximum frequency of 10 kHz is sampled using instantaneous sampling method. If Nyquist's sampling rate is followed, then what will be the sampling interval?
A television signal (video and audio) has a bandwidth of 4.5 MHz. The signal is sampled, quantized and binary coded to obtain a Pulse Coded Modulated (PCM) signal. (a) Determine the sampling rate if the signal is to be sampled at a rate of 20% above the Nyquist rate.(b) If the samples are quantized into 1024 levels, determine number of binary pulses (or digits) required to encode each sample.(c) Determine the binary pulse rate (bits per second) of the binary coded signal.(d) Calculate minimum bandwidth required to transmit this signal.
Q 5. A television signal (video and audio) has a bandwidth of 4.5 MHz. The signal is sampled,quantized and binary coded to obtain a Pulse Coded Modulated (PCM) signal.(a) Determine the sampling rate if the signal is to be sampled at a rate of 20% above theNyquist rate.(b) If the samples are quantized into 1024 levels, determine number of binary pulses (ordigits) required to encode each sample.(c) Determine the binary pulse rate (bits per second) of the binary coded signal.(d) Calculate minimum bandwidth required to transmit this signal.