Kindly answer correctly. Show all the necessary steps and checks QUESTION 1You have been instructed to join two existing roads by an even grade from point X toY. Point X is a known elevated mark on the centre of the first road and point Y is asimilar mark on the second road. You are required to supply the site engineer with thecut and fill at 10 metre intervals along the centre line of the new road.You have observed the following information in the field:DistancePointBSISFSElevationFrom X0.425+ 2673.0541.3481021.7222031.9923042.3024052.384502.3986072.1947082.25080Y2.09690+ 2671.383

You have been instructed to join two existing roads by an even grade fro Y. Point X is a known elevated mark on the centre of the first road and similar mark on the second road. You are required to supply the site engi cut and fill at 10 metre intervals along the centre line of the new road.

You have been instructed to join two existing roads by an even grade fro Y. Point X is a known elevated mark on the centre of the first road and similar mark on the second road. You are required to supply the site engi cut and fill at 10 metre intervals along the centre line of the new road.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A cylindrical object 84mm diameter, 158mm height and a mass of 593g, is placed in the tank, which co...

A: Diameter of the cylindrical object = 84 mm or 0.084 mm. height of the cylindrical object= 158 mm...

Q: A rectangular scow 9m wide, 15m long, and 3.6m high has a draft in seawater 2.4m. G is located 2.7m ...

Q: ne tank is filled with liquid with 1.0 specifi- d has a hole at point A. Inside the tank, a lloon fi...

A: According to given data The tank is filled with liquid with 1.0 specific gravity and has a hole at ...

Q: Two cars A and B have a velocity of 60 mph in the same direction. A is 250 ft behind B when the brak...

A: v= 60mph = 88ft/sec l= 250ft a = -10ft/s2 It has been asked in the question that what time will A ...

Q: The center lines of two parallel road tracks, 65 m apart, are to be connected by two simple curves w...

Q: can use the second photo as reference and please

Q: A simple and horizontal curve road has a degree of curve of 3°. Determine the design speed on this c...

Q: 1000 kg 800 kg 200 kg/m A D 2m t+ 4m - 2m R, R,

A: Given data: length of AB=2m length of BC=4m length of CD=2m At point B load is 1000KG At point C loa...

Q: For the truss shown, determine the force in members BD, CD, and CE stating whether the member force ...

Q: PROBLEM 1. A flanged bolt coupling is used to connect two solid shafts. Each shaft has a diameter of...

A: NOTE : According to guidelines, only problem 1 is solved. Please post problem 2 separately. Given, ...

Q: In a certain situation it was estimated that 25% of the braking force was applied to the rear brakes...

Q: A saturated silty clay encountered in a deep excavation is found to have a water content of 27.4%. U...

Q: Determine the sight distance of a vertical parabolic sag curve 225m long and connecting a -2 grade a...

A: Given, Length of curve (L) = 225 m Grade, G1 = -2% Grade, G2 = 3%

Q: Cable Analysis : Analyze. the loaded cables as shown. 7m Com to 35° 1GKN 20 KN

Q: Determine the force in each member of the TruSs shown i the figure and indicate whether the members ...

Q: The tangents of a compound curve have the following azimuths, AB = 216°30′, BC = 224°30′, and CD = 2...

Q: Perform a cantilever method to determine the force and moment of the three-storey frame given below....

Q: Your friend made an investment of P 45,000.00 for 60 days at 15% simple interest. If withholding tax...

A: To determine the net interest due for given investment. Given, Investment sum (A) = P 45000.0 Rate...

Q: : a) The initial metacentric height b) The righting or overturning moment when the scow tilts until ...

Q: A solid 0.64-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaf...

Q: TIME (minutes) CUMULATIVE (mm) PROBLEM 4 10 6.2 In a storm of 90 minutes 20 8.5 duration, the increm...

Q: W1 W2 B C. X1 X2 X3 X4 Given: X1 = m X2 = 3 X3 = 2.5 m X4 = 6. P- 15 kN 28 kN/m 28 kN/m E - 250 GPa ...

Q: What is the threshold torsion (kN-m) of a rectangular beam with a width of 446 mm and an over-all de...

A: Given, fck = 22.00 MPa fy = 404 MPa Assuming, balanced section, xudlim=0.00350.0055+0.87fyEsFor, fy=...

Q: A simple and horizontal curve road has a degree of curve of 3°. Determine the design speed on this c...

A: Degree of curve=3o e=0.06 f=0.15

Q: What’s the role of documentation in Manual Testing?

A: INTRODUCTION: Documentation is the process of arranging all the details related to certain project i...

Q: find DL, LL, SL & WL at each joint of main system. Assume all missing data webs 20+L Bottom chod SEC...

A: Given length l=200ft =60.96m rise R=20ft = 6.096m Dead load(DL): W=1100l3+5KN/m2 =1100...

Q: Determine the force of the members CF and CG. 2 kN 2 m В 2 m 2 m A SN kN 3 m F E

Q: A steel tape, known to be of standard length at 20°C, is used in measuring a 3,895.70m line. The coe...

Q: * 53% 4 7:48 PM Tue 8 Mar + : Oil flows into the pipe at A with an average velocity of 0.2 m/s and t...

Q: The diameter of the holes in the connection below is 20mm. The steel plate is made up of 10mm x 250m...

A: Given, b=250 mm db=20 mm Diameter of bolt hole on the plate, dh=20+1.5=21.5 mm Yield strengthfy=248....

Q: The rigid beam rests in the horizontal position on two 6061 aluminum cylinders having the unloaded l...

Q: A solid 45 mm diameter beryllium copper (E = 131 GPa; a = 17.0 x 10-6 /"C) rod is stress free when s...

Q: The beam is subjected to the loading shown. If the allowable shear stress is Tallow = 75 MPa and the...

Q: A tube well of 15 cm diameter penetrates fully an artesian aquifer 27 m thick. Determine the permeab...

Q: section width is reduced to IS m and channel D.50m.Find the change in water surface elevation.

Q: Given the following principal stresses and principal direction: ox = 27 MPa, oy = 15 MPa, txy = 6 MP...

Q: P 467 N 2m 7m 1m A 60° 450

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of understandin...

Q: 2. The driver of a vehicle travelling at 80kph upgrade requires 9m. less to stop after he applies th...

A: Given- Speed = 80 kph Coefficient of friction between the tires and the pavement = 0.50 To find - B...

Q: -30-mm diameter 250 mm -50-mm diameter 300 mm C

Q: B D For the truss shown, determine the force in members BD, CD, and CE stating whether the member fo...

A: For the truss shown, determine the force in members BD, CD, and CE stating whether the member force ...

Q: In the figure, a longitudinal hole is bored across the length of a cantilever beam having a rectangu...

Q: Why is it essential to measure the porosity and permeability of the soil?

Q: U-tube manometer is connected to a conical vessel as shown in figure. Manometer shows a reading of 8...

A: We have to determine the value of reading on the manometer when vessel filled with water.

Q: 1. Draw the shear and moment diagram and find the location of the maximum moment. 30KN 20KN/m 20KN.m...

Q: Determine the Maximum absolute shear from the shear diagram. Attach here the shear diagram and compu...

Q: Select the best answer .Show your solution 1. Determine the volume of direct run off in cu m that wi...

Q: Determine the force of the members CF and CG. 2 kN 2 m В 2 m 2 m А SN kN 3 m F E

Q: What is the importance of research to Engineering

A: Engineering is a scientific way of executing or build things which ensures safety, economy, efficie...

Q: Determine the following using Slope Deflection Method. W1 P W2 A B X1 X2 X3 X4 Given: X1 = 4 X2 = X3...

Q: ever beam shown and num absolute value of ng moment. Indicate th You may use the meth od or both

Concept explainers

Highway Safety

Proper highway safety refers to the methods or rules that prevent highway travelers from being killed or severely injured. Proper highway safety measures help to protect motorists, cyclists, pedestrians, passengers on public transport, and so on.

Question

Kindly answer correctly. Show all the necessary steps and checks

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Show your COMPLETE solution in 3 decimal places. Provide illustration and label accordingly. 6.A 5 ̊curve intersects a property line CD at point D. The back tangent intersects the property line at C which is 105.27m from the PC that is at station 2+040. The angle that the property line CD makes with the backtangent is 110 ̊50’. (a) Determine the distance CD, (b) Determine the stationing of point D, and (c) Determine the deflection angle of point D fromthe PC.
Instructions: Please provide complete solution for full credit and box final answer/s. Problem: Given lines AB, BC and CD, a reversed curve is to connect those three lines thus forming the center line of the new road. Find the length of the common radius of the reversed curve. LINES BEARING DISTANCES AB DUE EAST 57.6 m BC N68°E 91.5 m CD S48°E 109.2 m
In this solution, may I know where they got the 0.01 slope?
A 120mx120m lot is divided into 9 equal sections. Find the volume (m3) to be excavated if the ground surface is to be leveled to elevation 10m. The elevations of the ground surface at each corner are as follows: A = 19.2m B = 15.3m C = 16.9m D = 19.5m E = 17.2m F = 17.6m G = 16.2m H = 15.1m I = 17.2m J = 18.6m K = 18.2m L = 17.5m M = 18.8m N = 17.1m O = 16.2m P = 17.9m Round your answer to 3 decimal places.
A rectangular concrete canal is to carry 0.142cms.The bottom width is twice the depth. What should be the dimensions of the streamm cross-section if the slope is to be 0.001?n =0.013
A 120mx120m lot is divided into 9 equal sections. Find the volume (m3) to be excavated if the ground surface is to be leveled to elevation 10m. The elevations of the ground surface at each corner are as follows: A = 17.1m B = 19.2m C = 18.8m D = 19.2m E = 18.3m F = 19.6m G = 18.9m H = 17.6m I = 18.1m J = 15.2m K = 16.7m L = 16.2m M = 18.7m N = 16.4m O = 19.2m P = 17.5m
For the given road cross section notes, the width of the road is 11.00 meters with SSof 1:1. Find the earthwork volume using the following methods: • Average End Area• Prismoidal Formula• Prismoidal Correction• Road Sections STA 10 + 000 3.00 1.50 1.00 -8.50 0.00 6.50 STA 10 + 020 2.20 1.20 2.60 -7.70 0.00 8.1
Answer 2-3 2. A rectangular lot was measured using a 50 m steel tape which was found to be 0.025m too short. If the recorded length and width are 180 m. and 120 m. respectively,determine the following:a. Actual dimension of the lotb. The error in area introduced due to the erroneous length of tape 3. A 500 m. track is to be laid out on a straightaway course using a 50 m. tape known tobe 50.06 m long. Determine the measurements to be made on a 300 m track so that thecourse will have the correct length.
A1) Answer the following; a. From station 0+040 with a center height of 1.2m fill, the ground line makes a uniform slope of 6.5% to station 0 + 100, whose center height is 3.5m. Find the grade of the finished roadway. b. Station of P.T of a compound curve is at 15+480.14, l1= 30degrees, l2=36 degrees, D1= 4 degrees, and D2=5 degrees. what is the stationing of P.C.C? use arc basis.
SHOW COMPLETE SOLUTION PLSVALUES: X = 425Y = 25A = 5
A series levelling had been down along the centre line of the proposed road the distance between each two points (100m). If the elevation of the points A, E and H after completing the project should be 31m, 30m, and 31.5m respectively and these three points connected with straight lines having uniform gradient. Calculate the depth of cut and fill for the points C and G.
Your company have been awarded a road contract. As the senior Surveyor what are the necessary leveling processes that you will go through to construct the road.