you use a 30 m long column with an internal diameter of 0.25 mm and a film thickness of 0.25 μm. (a) Estimate the value of H for this column. b) On this column, a pair of compounds that you wish to separate has an alpha. value α of 1.01 and the k value of the second component k2 is 5. Will this columns provide a resolution of greater or less than 1 or this pair of compounds.? Explain

you use a 30 m long column with an internal diameter of 0.25 mm and a film thickness of 0.25 μm. (a) Estimate the value of H for this column. b) On this column, a pair of compounds that you wish to separate has an alpha. value α of 1.01 and the k value of the second component k2 is 5. Will this columns provide a resolution of greater or less than 1 or this pair of compounds.? Explain

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter20: Molecular Mass Spectrometry

Section: Chapter Questions

Problem 20.9QAP

See similar textbooks

Similar questions

1. In using the spectrophotometer PD 303, why is there a need to use water as blank when measuring the absorbance of each solution
An ethanol solution of 3.5 mg/100 ml of compound Y (150.0 g/mol) in a 1.00 cm quartz cell has an absorbance (A) of 0.972 at λmax=235 nm. What is its molar extinction coefficient? Report your answer to the correct number of significant figures. Do not include units in your answer. I need to know what is the correct number of sig figs for this question which will determine what the correct answer is.
1. Describe the different types of analytes which can be analyzed using the different methods of optical analyses. 2. Why is it that absorbance readings be done at lambda max?
Substances A and B have retention times of 16.40 and 17.63 min, respectively,on a 30.0-cm column. An unretained species passes through the column in 1.30 min. The peakwidths (at base) for A and B are 1.11 and 1.21 min, respectively. Calculate(a) the column resolution,(b) the average number of plates in the column,(c) the plate height,(d) the length of column required to achieve a resolution of 1.5.
2. In UV and visible spectrophotometry, the specimen is generally dissolved in a solvent, and determinations are made at room temperature using a path length of 1 cm. Give the most common solvents suitable for UV or visible spectrophotometry.
For an analysis of phthalates by GC-MS, the limits of detection and quantitation are 0.55 and 3.56 mg/g, respectively. Based on the results obtained below, how are the 3 samples reported? Sample Concentration (mg/g) A 4.50 B 0.055 C 0.56
Seawater was spiked with phosphate to achieve a quantifiable range of phosphate concentrations by the spectrophotometer. What components of the spectrophotometer or sample preparation could be changed that would improve detection limits?
0.1120 g of a solid sample containing copper was dissolved by acid and transferred to a 250.00 mL volumetric flask and volume was made up with distilled water. The solution was then diluted by a factor of 25. The final solution was analyzed by atomic absorption spectrophotometry and the concentration was found be 2.982 ppm, What is the weight percentage of copper in the original solid sample? Keep four significant figures in your final answer.
Suppose that s = 0.28 nA instead of 0.56 nA, but yblank is still 1.26 nA. Find the signal detection limit, the minimum detectable concentration, and the concentration of analyte in a sample with a signal of 7.0 nA.
Consider the separation of components A and B on a GC column. The retention time for component A is 1.4 min and for component B is 2.1 min. The width at the base for the peak due toA is 0.38 min and for the peak due to B is 0.53 min. Calculate the resolution, R, and tell whetherthe two peaks are considered to be resolved and why.
HPLC VFA analysis - why do I get so different peaks for very similar samples?
What is the purpose of reference beam in the double-beam spectrophotometer shown in Figure 20-1? Select all the correct answers. a)To correct for changes in source light intensity as a function of time b)to correct for changes in intensity of the light source as a function of wavelength c)to correct of scattering of light off the surface of the sample cuvette d)to correct for absorbance of the solvent e)to correct for changes in detector signal as a function of wavelength