You want to draw water from a stream running down a hill behind your house at a rate of 3 litres /s.To hand you have 30m of commercial steel tubing of inside diameter 30mm. At what vertical level above the house should you dam the stream to draw off the water?.

You want to draw water from a stream running down a hill behind your house at a rate of 3 litres /s.To hand you have 30m of commercial steel tubing of inside diameter 30mm. At what vertical level above the house should you dam the stream to draw off the water?.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Example: A dam holds back the water in a lake. If the dam has a small hole 1.4 meters below the…

Q: fluid passing a boundary of a system is 80,000 ft-lb. Determine the exit pressure if the inlet…

Q: 1. A jet of water strikes on series of cup shaped vanes which deflects it through 165 degrees If the…

Q: A pump has an efficiency of 65%. It is driven by a 0.75 horsepower motor. The pump produces a…

A: Given Pump efficiency = 65% Power of motor = 0.75 hp Pressure = 0.0174 psi To find Flow rate in m3/s

Q: A pump is installed in a pipe system, where at the suction side 1 m below the pump, an open…

Q: An irrigation line carries water from a lake down into an arid valley 810 ft below the surface of…

Q: 15! A closed rectangular tank full of water is 3m long, 2m wide and 2m deep. The pressure at the top…

Q: In Fig. X6.5.3, both nozzles discharge water horizontally into the atmosphere at 30 fps. Find 0 so…

A: Given Data The velocity of water in the pipe, V1=V2=V3=30 ft/s For pipe 2 Flow rate Q2=A2V2

Q: 6. A pump is located 4.5 m to one side of, and 3.5 m above a reservoir. The pump is designed for a…

A: kinematic viscosity of water at 5 °C is, v=1.519×10-6 m2/sec,Reynolds number,…

Q: Theoretical horsepower required to pump water at 100 GPM from a larger reservoir to the surface of…

Q: 4. An upright tank, full of water, has a height of 2m and a triangular base (cross section). If the…

Q: Air 25 kPa Blade Water 3m 659 Jet

A: Given that, Weight of the jet, W=100 kg,Height of water from jet, h=3 m,Discharge through the jet…

Q: A fan is rated to deliver 680 m3/min at a static pressure of 304 cm of water when running at 219 rpm…

A: To find the power at the changed conditions

Q: A pipe 12 mmm diameter with a velocity of 0.50 m/s is attached by a nozzle at the end having a…

A: To find: The velocity of the water in the nozzle. Given: The diameter is d1=12 mm. The velocity is…

Q: A fan described in a manufacturer’s table is rated to deliver 500 m3/min at a static pressure of 254…

A: The power at 516 rpm and 65 ℃: P = 25.3444 kW

Q: A 600mm by 300mm reducer connects two pipes. The velocity at the exit end of the reducer is 5m/s and…

Q: A horizontal axis wind turbine is installed at a location having free wind velocity of 15 m/s. the…

A: Given data wind velocity = 15m/s. Diameter = 80 m. radius =40 m To find the rotational…

Q: A horizontal pipe of (40cm) dia. expanded suddenly to (60cm) dia. with a flow rate of water equals…

A: Given data: - The initial diameter of the pipe is d1 = 40 cm. The final diameter of the pipe is d2…

Q: A pipe 12 mm diameter with a velocity of 0.50 m/s is attached by a nozzle at the end having a…

A: To find: The velocity of the water in the nozzle. Given: The diameter is d1=12 mm. The velocity is…

Q: The water turbine of a 5-MW hydro-power plant has specific speed of 40 rpm and discharge of 2020…

A: The approximate diameter of the jet is 191.2 mm.

Q: 200 kN/m Turbine 3 0.3 m /s'0.4 m

A: givenat inlet of turbine pressure P1=200KPadischarge Q=0.3m3/sdiameter of pipe d1=0.4mhieght of…

Q: Example 2.8. The inlet to pump is 10.5 m above the bottom of sump from which it draws water through…

A: Given data Pressure = 28 KN/m2 Atmospheric pressure = 100 kpa

Q: ) A 100-mm diameter plunger is being pushed at 60 mm/sec into a tank filled with oil having sp.gr.…

Q: A cenurifugai pump of i.3 u deiivers 3.5 n of 1.6 m/s. The cutlet blade angle is at 3 imneller…

A: Find the torque delivered by the impeller.

Q: 1. An open trapezoidal tank is accelerated horizontally at 6m/s2 along its length. Its bottom width…

A: As per Bartleby guidelines, since it is a multiple question, we will solve the first question for…

Q: An open vessel in the form of a frustum of a cone with a radius of 1.2m (bigger base), the smaller…

A: Given: The radius of frustum at base, R = 1.2 m The radius of frustum at top, r = 1 m The slope of…

Q: A 30m diameter wind turbine is placed on a 50m tower in terrain with a power law coefficient (a) of…

Q: For fig shown if water flow rate is 60 lit/s, Find (h) Note that Density: Pwater = 1 kg/m Pair = 1…

Q: best fits between the options of the graph A, B, C, D and F,

A: Given:- Static head= 85 Capacity= 195 To Find:- Best impeller & Expected Power consumption

Q: A groundwater well with produces 80 m/hr. and has a hydraulic conductivity of 20 m/d. Calculate the…

A: Given:-Q=80 m3/hrK=20 m/d% opening at screen = 17%Entrance velocity, Vi=1.55 cm/secDiameter of…

Q: Compute the heat transfer through the air condition if the outside temperature is outside…

A: Given data: Outside temperature, T∞=5 °C and inside room temperature, Ti=20 °C. Room dimensions are:…

Q: A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open…

A: As per Question Pipe diameter =10cm Discharge =35 L/s We have to find the total energy at the…

Q: A hydraulic cylinder is to compress a vehicle body in 17.45 seconds,The operation requires a stroke…

Q: A 0.025 m diameter pipe carries oil of sp. gr. 0.9 at a velocity of 3 m/s. At another section the…

A: Given :- At section 1 : Diameter (d1) = 0.025 m Velocity (V1) = 3 m/s At…

Q: A fan when driven by a 5.8 Hp motor at a speed of 800 rpm delivers 510 m3/min at a total pressure of…

Q: / For fig shown if water flow rate is 60 lit's, Find (h) Note that Density: Pwater=1 kg/m Par=1 kg/m

A: Given Dataρw=1kg/m3ρa=1kg/m3D1=500mm=0.5mD2=25cm=0.25mQ=60L/s=0.06m3/s

Q: Q3 The diameters in Fig. 6.3 are 750 mm and 500 mm. At the larger end the pressure is 650 kPa and…

A: Let ρ =density of water =1000kg/m3 g =Acceleration due to gravity =10m/s2 D1=Diameter at inlet…

Q: Maria Cristina falls located at south has a height of 100 meters, it discharges at constant rate 2.5…

Q: A car is traveling on a highway at 28 m/s. a) What is the pressure at the bottom of a car's gas…

Q: The outer diameters of fixed ram and brass bush are 120 mm and 150 mm and the stroke is 1.2m. If the…

A: The hydraulic accumulator is a device used for storing the energy of a liquid in the form of…

Q: A pipe of diameter 25 cm is suddenly enlarged to diameter of 50 cm. If pipe carries 350 lit/sec,…

Q: An oil of specific gravity 0.77 and viscosity 0.05 poise is flowing through a pipe of diameter…

A: GIVEN DATA- DENSITY =770 kg/m3 viscosity 0.05 poise = 0.005 Ns/m2 diameter=240mm Flow rate=50 lit/s…

Q: A hydraulic cylinder is to compress a vehicle body in 19.35 seconds,The operation requires a stroke…

Q: A cylindrical pipe with water flowing downward at 0.03 m3/s having top diameter of 0.08, bottom…

Q: A farmer must pump at least 100 gallons of water per minute from a dam to a field, located 25 f t…

A: Given Data Quantity of water =100 gallons /min= 6.308 Kg/sec=m density of water =1000 Kg/m3. height…

Q: The power 365 W is required to transmit 6 x 10- m/s of water. Find the loss of head due to friction…

A: P=ρQgH

Q: 3.58 The water tank in Fig. P3.58 stands on a frictionless cart and feeds a jet of diameter 4 cm and…

A: Step-1 Given Data diameter of jet d) = 4cm = 0.04 m…

Q: Q3: Water flows from reservoir A through pipe 1, diameter d, = 120 mm, length L=100 m, to junction D…

A: d1=120 mm L1=100 md2=75 mm ,L2=50 m d3=60 mm ,L3=30 mZA-ZB=12 mZA-ZC=20 m

Q: As shown in the figure, the water is directed downward in the installation with a 25 ° angle…

Concept explainers

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.

Question

HYDAYULICS

You want to draw water from a stream running down a hill behind your house
at a rate of 3 litres /s.To hand you have 30m of commercial steel tubing of inside
diameter 30mm. At what vertical level above the house should you dam the
stream to draw off the water?.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A pump raises 650 tonnes of pure water a height of 55m in 6 hours. If the pump efficiency is 100%, what is the power required to drive the pump?
A water jet has a diameter of 75mm and ahs a velocity of 15m/s. What is the horsepower exerted by the jet. ANSWER: 10hp
For a tank, calculate the volumetric flow of water, which comes out through a pipe, the tank is sealed, the depth is h1=2M, Qexit=0.05,substance water Vexit=? and Q=?.
sollve both, show both solutions and steps for both problems
A typical pump has a head that, for a given shaft rotationrate, varies with the fl ow rate, resulting in a pump performancecurve as in Fig. P3.181. Suppose that this pump is75 percent efficient and is used for the system in Prob.3.180. Estimate ( a ) the flow rate, in gal/min, and ( b ) thehorsepower needed to drive the pump.
If a pump discharges 284 liters per minute of water whose density is 985 kg/m3; find a) the mass flow rate in kg/min, and b) the total time required to fill a vertical cylindrical tank 3.05m in diameter and 3.05m high.
A pump has a displacement volume of 122 cm3. It delivers 0.0027 m3/s of oil at 1720 rpm and 85 bars. If the prime mover input torque is 175 N∙m What is the overall efficiency of the pump? What is the theoretical torque required to operate the pump?
A two storey building has two faucets, one in the basement and one in the firstfloor. The maximum water (ρ = 1000 kg/m3) velocity at the basement faucet, when the first floor faucet is closed, is 13 m/s. The faucet diameter is 1.5 cm.Neglect all losses. What would be a maximum height (from the basement floor) for a faucet,to still get a maximum exit velocity of 6 m/s?
If a pump requires a minimum of 2.75m of NPSH, how high (absolute value in meters) can the centerline of the pump be located above the top of an open tank that supplies a 27°C-water to the pump? The water tank is 1.83m high which is filled to the brim, and the total pipe friction is 0.70m.
(a) the total dynamic head (TDH) in meters (b) the water power (WP) in kW (c) the pump mechanical efficiency (%) if the power input to the pump is 15hp
A room has a volume of 349 m3. An air-conditioning system is to replace the air in this room every 81.5 minutes, using ducts that have a square cross section. Assuming that air can be treated as an incompressible fluid, find the length of a side of the square if the air speed within the ducts is (a) 2.00 m/s and (b) 7.00 m/s. a: b:
h. Thirty (30) liters/second of stream water must be pumped up a vertical height of 12 meters to irrigate a farm. If head loss in casing and pump results in 62% pump efficiency and the electric motor used has 91% efficiency, what horsepower rating should the motor have and how many kilowatts will it use while pumping?