Your answer is partially correct. A simply supported wood beam that is 13.5 m long carries a 39 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 155 mm, d = 410 mm, a = 105 mm, and c = 50 mm. Section a-a is located at x = 2.3 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. P H A B L 2L 3 3 Answer: (a) TH = i 46778 КРа (b) TK = i КРа 2629 (c) Tmax КРа i 1198 (d) Omax= MPa 26.94

Your answer is partially correct. A simply supported wood beam that is 13.5 m long carries a 39 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 155 mm, d = 410 mm, a = 105 mm, and c = 50 mm. Section a-a is located at x = 2.3 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. P H A B L 2L 3 3 Answer: (a) TH = i 46778 КРа (b) TK = i КРа 2629 (c) Tmax КРа i 1198 (d) Omax= MPa 26.94

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two wooden joists 100mm * 200 mm along the joint AB as shown in figure. Determine the normal and shearing stress in glued surface if P = 400 N
Two wooden joists 100mm * 200 mm along the joint AB as shown in figure. Determine the normal and shearing stress in glued surface if P = 400 N
The girder of a simple log bridge supports a wheel load W acting at any position along the span. In addition, the weight of one log and the planks it supports is equivalent to a uniform load of 850 N/m acting on the log. Determine the maximum permissible wheel load W (in kN) based on an allowable shear stress of 0.75 MPa if the maximum shear stress on circular sections is 4/3 of the shear force divided by the cross-sectional Choices: 28.9 38.7 77.4 30.2 Note:please help me in this sample problem thank you
For the beam in question 1, determine the maximum bending and shear stressesat point C, at point P of the section. Represent the stress cube
Determine the force in each member of the structure and establish whether the members are in tension or compression. Establish P1= 45 KN, P2= 30 KNSolve the problem considering the following: The force P1 will be the maximum point of a triangularly distributed load with a horizontal distribution of X meters.You must leave the solution in terms of X and show the particular solution when X is equal to 0m and 2m.
A cantilever beam supports the loads shown. The cross-sectional dimensions of the shape are also shown. Assume a = 0.4 m, PA = 2.0 kN, PB = 6.0 kN, PC = 3.0 kN, d = 85 mm, bf = 105 mm, tf = 5 mm, tw = 9 mm. Determine(a) the maximum vertical shear stress.(b) the maximum compression bending stress.(c) the maximum tension bending stress.See the coordinate system for the beam in the problem figure with the origin of the x axis at the fixed support. Consider four points along the beam’s axis:Point A at x = 1.2 mPoint B at x = 0.8 mPoint C at x = 0.4 mPoint D at x = 0Break the beam into three segments: AB, BC, and CD. Enter the shear force in each segment with its correct sign based on the coordinate system in the problem figure and the sign convention for shear forces in Chapter 7.Answers: VAB = kN VBC = kN VCD = kN Part 2 Enter the maximum shear force magnitude in the beam. Since this is a magnitude, enter a positive value.Answer: Vmax = kN…
From the given simply supported beam below, determine the following: g. The shear stress at the mid-point of the beam.
A cantilever beam supports the loads shown. The cross-sectional dimensions of the shape are also shown. Assume a = 0.6 m, PA = 2.5 kN, PB = 7.0 kN, PC = 4.0 kN, d = 100 mm, bf = 110 mm, tf = 10 mm, tw = 7 mm. Determine(a) the maximum vertical shear stress.(b) the maximum compression bending stress.(c) the maximum tension bending stress. See the coordinate system for the beam in the problem figure with the origin of the x axis at the fixed support. Consider four points along the beam’s axis:Point A at x = 1.8 mPoint B at x = 1.2 mPoint C at x = 0.6 mPoint D at x = 0Break the beam into three segments: AB, BC, and CD. Enter the shear force in each segment with its correct sign based on the coordinate system in the problem figure and the sign convention for shear forces in Chapter 7.Answers: VAB = kN VBC = kN VCD = kN Enter the maximum shear force magnitude in the beam. Since this is a magnitude, enter a positive value.Answer: Vmax = kN Enter the…
The cantilever beam shown has the following dimensions: a = 300 mm; b = c = 400 mm; d = g = 24 mm; e = g = 96. The loads are ωo = 2 kN/m and P = 3 kN. Determine the maximum bendingstress and the maximum shear stress in the beam.
A wooden post supports a 6-kip axial load as shown at right. Determine the stress at point A when: a. b = 0 b. b = 1 in c. b = 3 in
If the beam is subjected to a bending moment of M = 5 kN # m, determine the bending stress developed at point A and sketch the result on a differential element at this point.
Determine the force in each member of the structure and establish whether the members are in tension or compression. Establish P1= 45 KN, P2= 30 KN Solve the problem considering the following: The force P1 will be the maximum point of a triangularly distributed load with a horizontal distribution of X meters. You must leave the solution in terms of X and show the particular solution when X is equal to 0m and 2m.