Your selection was a gas-turbine power plant operating on an ideal Brayton cycle and according to themanufacturing datasheets it has the following specifications:A pressure ratio of 14.77.The gas temperature is 350 K at the compressor inlet and 1500 K at the turbine inlet.Under the assumption of standard air, perform the following:1. Gas temperature of the compressor and the turbine exits,2. Back-work ratio,1, discuss anyWnet3. Thermal efficiency using the formula nthand by formula nth = 1qin(k-1)/k >differences and explain it.

Given data: The pressure ratio is P2P1=14.77 The inlet temperature at the compressor is T1=350 K…

Your selection was a gas-turbine power plant operating on an ideal Brayton cycle and according to the manufacturing datasheets it has the following specifications: pressure ratio of 14.77. The gas temperature is 350K at the compressor inlet and 1500 K at the turbine inlet. A Under the assumption of standard air, perform the following: 1. Gas temperature of the compressor and the turbine exits, 2. Back-work ratio, 3. Thermal efficiency using the formula Nth = Wnet and by formula nth = 1 - din 1 discuss any (k-1)/k > differences and explain it.

Your selection was a gas-turbine power plant operating on an ideal Brayton cycle and according to the manufacturing datasheets it has the following specifications: pressure ratio of 14.77. The gas temperature is 350K at the compressor inlet and 1500 K at the turbine inlet. A Under the assumption of standard air, perform the following: 1. Gas temperature of the compressor and the turbine exits, 2. Back-work ratio, 3. Thermal efficiency using the formula Nth = Wnet and by formula nth = 1 - din 1 discuss any (k-1)/k > differences and explain it.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a gas turbine power plant operating on an ideal Brayton cycle having a pressure ratio of 10. For simplified standard cold air assumptions, determine the thermal efficiency, in %.
Air enters the compressor of a gas turbine at 100 kPa and 25°C. pressure ratio 5 and For a maximum temperature of 850°C, the back work rate and thermal efficiency of the Brayton cycle Please specify.
Consider a simple ideal Rankine cycle and an ideal regenerative Rankine cycle with one open feedwaterheater. The two cycles are very much alike, except the feedwater in the regenerative cycle is heated byextracting some steam just before it enters the turbine. Compare the efficiencies of these two cycles. Showyour complete solution and diagram’s.
A gas turbine power plant operating on an ideal brayton cycle has a pressure ratio of 8. The gas temperature is 320k at the compressor inlet and 1400k at the turbine inlet. Using the air-standard assumptions, determines: 1. The back work raio 2. The temperature at the exits of the turbine and exits of the compressor 3. The thermal efficiency in decimals
A gas turbine power plant working on Brayton cycle, Explain the working principle of the cycle with physical diagram as well as P-V and T-s diagrams, and with all the required details
Draw and label the P-V and T-S diagrams. A 150 MW gas turbine power plant running on Ideal Brayton cycle has the following initial conditions; air at 22°C & 95 kPa. The compression ratio is 7 and the temperature at the turbine is 910°C. Determine the following:a. Heat Added, per unit massb. Thermal Efficiencyc. Mass flow rate, kg/min
For an ideal cold air-standard Brayton cycle with a compressor inlet temperature of 300 K and a maximum cycle temperature of 1700 K, use Eq. in the picture to find the compressor pressure ratio that maximizes the net power output per unit mass flow. Assume k = 1.4
A 150 MW gas turbine power plant running on Ideal Brayton cycle has the following initial conditions; air at 22°C & 95 kPa. The compression ratio is 7 and the temperature at the turbine is 910°C. Draw the P-V and T-S diagrams and determine the following: d. Thermal Efficiency e. Mass flow rate, kg/min
First you selected a gas-turbine power plant operating on an ideal Brayton cycle and according to the manufacturing datasheets it has the following specifications:• A pressure ratio of 10. • Heat is added to the cycle at a rate of 500 kW• Air passes through the engine at a rate of 1 kg/s• The air at the beginning of the compression is at 70 kPa and 0 C.Task 1Investigate the principles of operation for a gas turbine power plant by considering the following:1. Construct T-S and P-V diagrams while discussing the operation of a gas turbine power plant2. Describe the difference between closed and open gas turbine engine3. Explain how a closed gas turbine engine would be combined with a steam power plant. 4. Explain why Brayton cycle is more preferred over Rankin cycle in power plant stations? And how would you enhance the performance of a Brayton cycle?
Instead, assume variable specific heat A gas-turbine power plant operates on the simpleBrayton cycle between the pressure limits of 100 and 800 kPa.Air enters the compressor at 308C and leaves at 3308C at amass flow rate of 200 kg/s. The maximum cycle temperatureis 1400 K. During operation of the cycle, the net power outputis measured experimentally to be 60 MW. Assume constantproperties for air at 300 K with cv 5 0.718 kJ/kg·K, cp 51.005 kJ/kg·K, R 5 0.287 kJ/kg·K, k 5 l.4.(a) Sketch the T-s diagram for the cycle.(b) Determine the isentropic efficiency of the turbine forthese operating conditions.(c) Determine the cycle thermal efficiency.
A 120 MW gas turbine power plant running on Ideal Brayton cycle has the followinginitial conditions; air at 22°C & 95 kPa. The compression ratio is 7 and the temperature atthe turbine entrance is 910°C. Determine the following:a. Thermal Efficiencyb. Mass flow rate, kg/min
Consider a simple Brayton cycle using air asthe working fluid; has a pressure ratio of 12; has amaximum cycle temperature of 600C; and operates thecompressor inlet at 100 kPa and 15C. Which will have the greatest impact on the back-work ratio: a compressorisentropic efficiency of 80 percent or a turbine isentropicefficiency of 80 percent? Use constant specific heats atroom temperature.