z +1 H(z) a) If we assume that this is a causal system, what is the region-of-convergence (ROC) that corresponds to the system function? b) If this is a causal system, is the system stable (justify)? c) Derive the time-domain impulse response of the filter for the causal ROC (use method of residues!!!)

z +1 H(z) a) If we assume that this is a causal system, what is the region-of-convergence (ROC) that corresponds to the system function? b) If this is a causal system, is the system stable (justify)? c) Derive the time-domain impulse response of the filter for the causal ROC (use method of residues!!!)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A robotic system with transfer function ?(?) =(100)/(s(0.1s+1)(0.1s +1)) is controlled with gain K as shown in the figure. A)To analyze the frequency response of this system, draw the Nyquist graph. B)Apply the Nyquist stability criterion. C)Verify the stability analysis you made in part (b) by plotting root locus plots for the positive and negative values of the K gain. D)Calculate the gain value that makes this system borderline stable and show it on Nyquist and Root locus graphs. E)Calculate the gain margin, phase margin, gain crossover frequency and phase crossover frequency values. F)Explain whether the system is stable over the gain margin and phase margin values. WE NEED TO SOLVE THE PROBLEM IMMEDIATELY. PLEASE HELP.
Practically, the de-emphasis filter in an FM receiver unit is often a simple resistance-capacitance (RC) circuit with transfer function. Hde(f)=1/(1+j2πfRC) i) Determine the 3-dB bandwidth and equivalent bandwidth. ii) Presume the modulating signal has bandwidth W, the carrier amplitude is A, and the single-sided power spectral density of the white Gaussian noise is N0. Solve for the noise power at the output of the de-emphasis filter circuit. iii) Find the noise power without the de-emphasis filter. iiii) Supposing RC = 6 × 10−5, and W = 15 kHz. Calculate the improvement in the output signal-to-noise ratio (SNR) provided by the de-emphasis filter. Express it in decibel (dB).
Impulse response of an LTI system is given by h(n)=δ(n+2)-2δ(n+1)+3δ(n)-2δ(n-1)+δ(n-2) = {1,-2,3,-2,1} a) Give the system function H(z), its ROC, and the frequency response H(ejω). Is this system stable? causal? Explain b) Obtain the spectrum, X(ejω), of x(n) = 3δ(n)+ 2sin(0.4 π n) + cos(0.8 π n) by using DTFT. Then calculate X(z). c) x(n) is applied to the LTI system h(n). Find the output spectrum Y(ejw) and Y(z).
a system whose closed-loop transfer function is given by G(s)=K/s(s^2+s+1)(s+2)+K derive a Routh-Hurwitz array to determine the stability of the system.
The response of a Butterworth filter is required to fulfill the following specifications: f_{p} = 1000Hz fs = 5000 Hz, A_{p} = 2dB A_{s} = 40dB Determine the following (i) Minimum filter order required to satisfy these specifications (ii) The 3dB corner frequency for this filter (iii) The transfer function of the filter H(s) b. Synthesize the filter described in part (a) above by continued fraction expansion to give a lossless ladder network terminated at both ends with 600 resistor. Draw the circuit.
1. Finding the closed loop transfer function of the system2.What is the steady state error of the system when a unit ramp signal is applied to its input?3. Given Km=5 and Kb=0.01, what should be the K value for a steady-state error to occur at the unit ramp input of the system?
A continuous time signal, x(t) = sin(20πt) + cos(40πt), is sampled uniformly at intervals of T to obtaina discrete time signal,x(n) = sin(πn/5) + cos(2πn/5).a) What is the value of T assuming no aliasing has occurred?b) Assume both frequency components have been aliased. In this case, is your choice of T unique? If not,specify some choices of T consistent with the information given
A numerical filter design problem is given. This filter, which is desired to be causal and stable, suppresses 0 and π frequencies (having zero at z1=1 and z2=-1 points) and passes π/2 and –π/2 frequencies (p1=rejπ/2 and p2=re-jπ/2). have poles at the points) is desired. By choosing an appropriate r-value, the filter: a. give the system function and frequency response,b. Give the unit impulse response,c. Give the difference equation.
Consider a closed-loop system with a zero-order hold. Consider G,(s) =400/(s^2+400) Determine the closed-loop transfer function T(z) for the system at T=1 sec.
First calculate the transfer function H(z) from the following difference equation.Then extract the filter parameters (as and bs) that are rquired to implement this filter in Python. y[n] = 2y[n-2] + 7y[n-1] + 4x[n] a = .. , .. , .. , .. b = .. , .. , .. , .. Please show me step by step to understand it clearly
Let the impulse response of a filter be ℎ[?] = {ℎ[0] = −0.5, 0.5}a) Calculate the frequency response ?(???). Is it a low-pass or a high-pass filter? Plot boththe magnitude and phase responses.b) Obtain the I/O relation for this filter.c) Is this a causal filter? Explain your answer.
A finite impulse response (FIR) high-pass filter is designed using the Window Method. The required specifications are: fstop = 2kHz, fpass = 4kHz, stopband attenuation = - 50dB, passband attenuation = 0.039dB and sampling frequency fs = 8kHz. (a) Which of the following window(s) can be used to implement such a filter? Give justification. Rectangular, Hanning, Hamming, Blackman