What is the purpose of an ammeter shunt?

Q: a) The approximate approach. b) The exact approach.

A:

Q: When is the current yeild a good approximation of the yeild to maturity?

A:

Q: What is multimeter

A: Multimeter is used to measure basic electrical measurements.

Q: 45. A switch or circuit breaker can be used as both the controller and disconnecting means if it a.…

A: a switch or circuit breaker can be used as both the controller and disconnecting means if: a) opens…

Q: What is the negative effect of operation a contactor coil above or below it's rated voltage

A: The contactor operational limit is 85 to 110 percent of the rated coil voltage.   The percent…

Q: Can someone solve for total resistance, amperage, volt drop on r1 r2, and ir5?

A:

Q: What Is the opposite of redistance

A: Resistance R The property which is oppose flow of charge carriers( electrons  ) .the element is…

Q: Ammeter reading?

A:

Q: Indicate the functional elements of the following measuring devices shown in Figure (6 Marks)…

A: A bourdon tube pressure gauge is a mechanical pressure gauge that does not require any electrical…

Q: List the types of the thyristor protection circuits ? And which one of them is the preferred one

A: For the protection of the Thyristor different methods are used depending on the kind of protection…

Q: Is it suitable to use a Thyristor in switching mode power supplies

A: In this question , we will define is it suitable to use a Thyristor in switching mode power supplies…

Q: achine is operating at rated voltage

A:

Q: Three types of electric devices A, B, and C are connected in series across a 115-volt ac source, and…

A: In thid question we will find given device types with given information...

Q: method of heat transfer principle is used to monitor changes in temperature in non contact type…

A: The solution is provided in the following section:

Q: Level to voltage transducer based on Buoy and Chain

A: Since you have asked multiple question ,we will slove the first question for you .If you want any…

Q: Slip rings and brushes

A: Concept: A device which is used for conducting the current between the stationary wires and the…

Q: How do you prove the correct operation of a digital multimeter? Present your answers in tabulated…

A:

Q: Briefly explain Clippers and Clampers with some examples.

A: Clippers are also known as wave shaping circuits or clippers are also known as limited circuits. In…

Q: Compare between servo motor and universal motor

A: Solution Servo motor does not rotate freely and continuously like DC motor. Its rotation is limited…

Q: Marks) Scale Containe Bourden tube Liquid veih -Pointe Lever Weak restoring spring Georing Diaphragm…

A: Measuring devices- Devices which are used for measuring particular parameters are known as measuring…

Q: 3. What is a Synchronizing Lamp?

A: Synchronizing lamps method uses three lamps that are connected between the generator terminals and…

Q: Discuss the operation of a multi-meter

A: Solution :    In the above question they are interested to know the operation of a multimeter.   As…

Q: How to get Multisim to automatically reorganize circuits?

A: Introduction Modularization and reuse are beneficial not only in software development, but also in…

Q: 4. (a) Draw the IV characteristics of a thyristor and explain what the importance is of the…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Harmonics due to variation of airgap reluctance is called...............

A: Harmonics due to variation of airgap reluctance is called Slot or Tooth Harmonics.

Q: Describe and Explain what occurs in each of these circuits when the pushbutton switch is actuated…

A: The SCR is a unidirectional device that allows the current to flow in one direction and opposes it…

Q: high

A:

Q: Screw eye ime o two forces

A: The cosine law is applicable to find the resultant of any two quantities. It requires the magnitudes…

Q: What is a clamp-on ammeter and what electrical principal does it operate

A: we need to answer What is a clamp-on ammeter and what electrical principal does it operate

Q: A shunt device that remains connected to the meter movement and thereby eliminates contact…

A: A shunt device

Q: In power station, the cost of lubricating oil is high. ...

A: Lubricating oil is used to provide lubrication to the engine.

Q: What happens when the switching device interrupts the low-voltage current flow I. The coil primary…

A: when the switching device interrupts the low-voltage current flow I the coil primary windings is

Q: 8. Which one of the following is used as a recorder in measurement system? a. Digital Printer b.…

A: Accept the thermistors all other devices are only measuring devices they could not record the Data.…

Q: What is a line refernce number in electrical prints

A: For developing the circuit diagram, it needs to be identified as the unique components. The…

Q: Deter mine: a) IB, Ic, DE b) VRE , VRC, VCE

A:

Q: A load connected between the terminals started drawing 3A current and terminal voltage dropped to…

A: It is given that: ILo=3 ATerminal voltage dropped to 95 % of it's no-load value.

Q: what are the different types of Damping in meter instruments?

A: There are four type of damping used in meter instruments Electromagnetic damping Air friction…

Q: Enumerate the procedure in making a double-threaded screws

A: Having two screw threads instead of one; said of a screw in which the pitch is equal to twice the…

Q: Are used as electrically controlled switches

A:

Q: 5) A Solid State Relay (SSR) can or should be used over a mechanical relay wher a) No mechanical…

A: A solid state relay is preferred over mechanical relay because of following reasons :- (a) the solid…

Q: What is the part of analog multimeter? Labeled and discuss each parts

A: The different part of analog multimeter labeled as, Needle pointer Scale Zero-ohm adjustment knob…

Q: lap-wound

A:

Q: What is the work of electronic scales

A: The detailed answer is solved below according to the given parameters and instructions in the…

Q: When is the resistance of an ideal ammeter is zero?

A: Given: When is the resistance of an ideal ammeter is zero?