What does it mean for an air mass to have 70% relative humidity?

Q: The cable supports the loading shown. Determine the magnitude of the vertical force P so that yC = 6...

A: ∑M@A=0Fcdcos39.81(8+2)+Fcdsin39.81*6-P(8+2)-6(2)=0Fcd(10cos39.81+6sin39.81)-10P-12=011.523Fcd-10P=12...

Q: A center-point bending test was performed on a 2 * 4 wood lumber according to ASTM D198procedure wit...

A: Given:- 2 X 4 wood lumber ASTM D!(* Span-4 ft 4in side Maximum load = 240kips deflection = 2.4 inche...

Q: Two wooden joists 100mm * 200 mm along the joint AB as shown in figure. Determine the normal and she...

A:

Q: The net weight of a soil specimen before drying is207 gr. And its dried weight after drying in an ov...

A: Given: The soil mass before drying is 207 gr. The soil mass after drying is 163 gr. The volume of th...

Q: A 36-lb triangular plate is supported by three wires as shown. Determine the tension in each wire, k...

A: Consider the free body diagram of the triangular plate:

Q: A particular soil failed under a major principal stress of 300 kN/m2 with a corresponding minor prin...

A: GIVEN DATA: σ1=300 KN/m2σ3=100 KN/m2ϕ=30∘FOR SAME SOILσ3=200 KN/m2

Q: How the engineering geology course can help you to practice engineering in your future job

A: Engineering geology is the branch of science that deals with the study of the earth, minerals its en...

Q: find approximate reaction at A I upvote solution

A: Consider the Free body diagram 

Q: n the irrigation efficiency is 80%, conveyance losses are 20% and the actual depth of watering is 16...

A: The given data is: The irrigation efficiency =80% Conveyance losses=20% Watering depth=16 cm

Q: A clay soil tested in a consolidometer showed a decrease in void ratio from 0.9 to 0.8 when the pres...

A: Given data: A clay soil decrease in void ratio from 0.9 to 0.8 Pressure was increased from 0.2 to 0....

Q: draw the shear force and bending moment diagrams and find the maximum shear force, maximum bending...

A: Finding out bending moment and shear force diagram. 

Q: A circular tank of diameter 1.25 m contains water up to a height of Sm. An orifice of 50mm diameter ...

A: The orifices is the small opening through which the fluid pass through.  The orifice is majorly clas...

Q: Subject is Advance Fluid Mechanics.

A:

Q: Determine the reactions at the supports A, B, C, and D.

A: Consider the diagram of the beam;

Q: Determine the magnitude and direction of the resultant of forces acting on the plate shown in figure...

A:

Q: After selecting the boards to use for the top and bottom plates, the next step in building a platfor...

A: First measure all the dimensions and the material accordingly. After that , cut the dry wood accordi...

Q: Note: This is not an assignment question and not a graded question

A: The azimuth of lines AB,BC, CD ,DA can be calculated in the following way Note:-We are assuming the ...

Q: Identify the four primary types of transportation regulation. Describe the purpose or rationale for ...

A: The significance and also the comprehensive result of transportation on the economy and also the gen...

Q: Classify each of the beams shown as statically determinate or statically indeterminate. If staticall...

A: The relations are to be satisfied, For a stable and statically determinate structure, r=3n For a sta...

Q: Determine the absolute maximum moment in the beam due to the loading shown.

A: Resultant load:R=40+25+20R=85KNResultant load is applied at a distance of x:x=20×(4+1.5)+25×485x=2.4...

Q: Determine the moments at A, B, and C, then draw the moment diagram. Assume the support at B is a rol...

A: Solution Given data Beam with 6 KN Point load and 0.5 K/ft UDl at half of the beam Support condition...

Q: Finding the expanded depth of the uniform mediumFilter medium sand grains (0.4mm in diameter)Ψ= 0.85...

A: when the diameter of particle is greater than 0.1mm than , The expression for settling velocity is g...

Q: A stud had dimensions of 38 mm * 89 mm * 2.438 m and a moisture content of 150% when it was prepared...

A: For tangential direction: Initial length = 9=38mm percentage of shrinkage for 0 percent moisture con...

Q: The office building has interior columns spaced 5 m apart in perpendicular directions. Determine the...

A: Space between interior columns is 5 m. Show the interior columns of a storage warehouse in the diagr...

Q: A 450 slope has been excavated to a depth of 8m in saturated clay which has following properties; un...

A: GIVEN DATA: ARC LENGTH=18.84 m RADIUS=12m DEGREE OF SLOPE=45∘ UNIT WEIGHT γ=20 KN/m3 CU=60KPA ϕ=0

Q: Determine the shear and moment in the beam shown as a function of x.

A: The shear force and bending moment is calculated with using the statically equilibrium equation,  ∑F...

Q: It is required to determine the height oftwo concentric cylinders used to construct a rotational v...

A:

Q: where fn is 55 and mn is 76

A: Given data: F1=55 kN=55×103 NMass of ring (M)=76 kgsWeigh of ring (W)=76×9.81 =745.56 N The free bod...

Q: A saturated specimen of cohesionless sand was tested in triaxial compression and the sample failed a...

A: Given data: Deviator stress (σa) =482 kN/m2 cell pressure (σc) = 100 kN/m2 The major principal stres...

Q: Note: This is not an assignment question... Please answer both questions... Pleaseeeeeee

A: GIVEN- At the end of week 2 Activity, A is 100% complete, Activity, A is 40% complete,

Q: show fbd

A: Fo=Force at plane O  = -15 jNFA=Force at plane A  = -20  iNR=Resultant =FA+Fo=-20i-15jR=-20i-15jN

Q: A glulam beam with a manufactured depth of 12 in. at 14% moisture content. Assumingcommon values for...

A: Given:- d=12in w=14% Moisture content increased to 35% To find:- new depth of beam

Q: NOTE,  the vertical deflection at joint C does not exceed 10mm (it cannot be B as it is a pin suppor...

A: