As shown in the figure, a curved bar ABC is subjected to loads in the form of two equal and opposite forces P = 5.1 kN, . The axis of the bar forms a semicircle of diameter 2 m. Determine the axial force (kN) acting at a cross section defined by the angle θ = 36°.

Q: The solid 1.25-in.-diameter rod shown in Figure is subjected to a uniform axial distributed loading…

A:

Q: Q1: The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical…

A:

Q: A bracket ABCD having a hollow circularcross section consists of a vertical arm AB (L 5 6 ft),a…

A:

Q: (6) For the composite beam shown in the figure, which is bended about a horizontal axis by a couple…

A:

Q: A circular post, a rectangular post, and a post of cruciform cross section are each compressed by…

A: Given: Diameter and the depth of rectangular and cruciform post=d Load acting at corner of the each…

Q: Determine the maximum tensile stress σt , maximum compressive stress σc, and maximum shear stress…

A:

Q: The extended beam ABC in the figure below is pin-supported at A and roller-supported at B. For the…

A:

Q: A two-step bar subjected to loading condition as shown in below figure is fixed at one end and the…

A:

Q: 1) Three-bar truss ABC as shown in figure is constructed of steel pipes having a cross-sectional…

A: Given data: The cross sectional area is A=3500 mm2 The modulus of elasticity is E=210 GPa The load…

Q: A horizontal load Pis applied to an assembly consisting of two inclined bars, as shown in the…

A:

Q: A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape…

A: Answer: (a) The maximum tension bending stress is 1530.2124 psi. (b) The maximum compression bending…

Q: A rectangular bar having width w = 5.00 in. and thickness t = 1.00 in. is subjected to a tension…

A:

Q: The segment AB of the steel torsion bar is a cylindrical tube of constant 2-mm wall thickness.…

A:

Q: Don't waste time by submiting Wrong answer.

A: Option c is the correct answer.

Q: A solid circular steel cylinder S is encased in a hollow circular copper tube C (see figure). The…

A: Given, Compressive force P= 97 kN The cross-section area of the steel cylinder, As=1422 mm2 Modulus…

Q: The beam will fail if the maximum bending moment reaches 900 Nm or the maximum shear force becomes…

A:

Q: A rectangular bar having width w = 4.75 in. and thickness t = 2.00 in. is subjected to a tension…

A:

Q: 2)- A bar AB of length=300 cm and diamater of 20 cm (see the figure below) is made of two different…

A: Given data:The diameter of the bar is d=20π cm=200π mm The length of each segment of the bar is…

Q: The extended beam ABC in the figure below is pin-supported at A and roller-supported at B. For the…

A:

Q: 3) The rigid horizontal bar AB is supported by three vertical rods as shown in the figure and…

A:

Q: A horizontal load Pis applied to an assembly consisting of two inclined bars, as shown in the…

A:

Q: A rectangular bar having width w = 7.00 in. and thickness t = 1.00 in. is subjected to a tension…

A:

Q: A rectangular bar having width w = 6.50 in. and thickness t = 1.50 in. is subjected to a tension…

A:

Q: The rigid beam BC shown in the figure is supported by rods (1) and (2) that have cross-sectional…

A: Given:A1=175 mm2A2=300 mm2w=16 KN/mL=2.8 ma=1.7 m

Q: Q1: The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical…

A:

Q: The rigid beam BC shown in Figure is supported by rods (1) and (2) that have cross-sectional areas…

A: Given data: A1=175 mm2A2=300 mm2w=15 kN/mL=3 ma=1.8 m Need to determine the stress in each bar.

Q: A rectangular bar having width w = 6.50 in. and thickness t = 1.25 in. is subjected to a tension…

A: Given:- width of bar=6.50 in,thickness of bar=1.25 in,area of cross section=(6.5×1.25)=8.125…

Q: Q / The figure below shown that the three bars are supported a rigid beam ACE. The bar CD is made of…

A:

Q: The horizontal rigid beam ABCD is supportedby vertical bars BE and CF and is loaded byvertical…

A: Given             E = 200 GPa Area, ABE= 11,100 mm2        ACF = 9280 mm2. Find   Deflections

Q: Q: The homogeneous bar shown in Figure is supported by a smooth pin at C and a cable that runs from…

A:

Q: The figure shown below

A: The cross-sectional area of the bars is Consider the diagram shown below for the beam ACE, Taking…

Q: In the figure, the horizontal rigid beam ABCD is supported by vertical bars (1) and (2) and is…

A:

Q: Q.2 A square timber beam used as a railroad tie is supported by a uniformly distributed loads and…

A: Given: ununiform distributed load→W1=24 KN and W2=48 KN Hence upward uniform distributed load:…

Q: C The rectangular bar has a width w = 100 mm and a thickness of 75 mm. The shear stress in the plane…

A:

Q: (a) Draw the free body diagram and determine the reaction forces at joint A (b) Determine the…

A: for solution refer below images.

Q: A horizontal load P is applied to an assembly consisting of two inclined bars, as shown in the…

A:

Q: The rigid beam BC shown in the figure is supported by rods (1) and (2) that have cross-sectional…

A: according the the given figure

Q: 1,2 m -0,6 m Im Çap:50 mm The system in the figure is carried by a 50 mm diameter column. If the…

A: Solution: We need to find the critical load to prevent the column BC from buckling, since both ends…

Q: The curved rod in the figure below has a radius r and is fixed to the wall at B. Determine the…

A:

Q: Consider the two-member frame shown. Suppose that w1 = 280 N/m , w2 = 450 N/m . Follow the sign…

A:

Q: A flat bar of rectangular cross section, length L, and constant thickness tis subjected to tension…

A:

Q: A uniform bar AB weighing 500 kg is supported at both end by a cable as shown in the figure.…

A:

Q: A fuselage with a circular cross section has 16 stringers, which 4 stringers were fitted at the axes…

A:

Q: Q.2. A rectangular section 300 mm wide and 500 mm deep is used on a span of 6 m for the loading…

A:

Q: Figure 1. In the figure shown, a bar ABC with negligible mass carries a 20 kN load and is supported…

A: Allowable stress of pin is not given to find the diameter of the pin  put this value in the…

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.