different frequency bands. These are depicted in the figure below: Fig: Carrier Aggregation in LTE advanced networks Extended MIMO: The MIMO systems use multiple antennas at both transmitter and the receiver in order to increase the bit rate and the throughput. LTE can support up to 4 x 4 MIMO, whereas LTE-advanced can have a maximum of 8 x 8 MIMO for downlink and 4 x 4 MIMO for the uplink. This
CE3.13 Since I had previous experiences in using the survey software, I recommended the usage of Ekahau site survey. Even though there are different survey tools were available in the market, the reason I selected this tool is that it facilitates WLAN planning at the pre-deployment stage. I advised Mr. Surya, who was the lead systems engineer, to use of this tool for the detection of the coverage holes and co-channel interference zones in the various location of campus. Ekahau wireless adapter was
Finally, we give practical recommendations of how using the proposed combined LTE/MIMO Network with a Multi-beam antenna system will increase the system's capacity. This will allow the designers of wireless networks to obtain maximum data rate, better channel spectral efficiency and less bit error rate, and as a result, much better service
ABSTRACT In this work, The field of wireless sensor systems have turned into a concentration of serious research as of late, particularly to monitor and describing of expansive physical situations, and for following different ecological or physical conditions, for example, temperature, weight, wind and dampness. Wireless Sensor systems can be utilized as a part of numerous applications, for example, untamed life observing, military target following and investigation, risky situation investigation
Number of reception (independent) by the MIMO system is called diversity gain. The Diversity Gain, which is also known as Diversity Order is given by . Where  is number of receiving antenna and is number of Transmitting antenna. II. SYSTEM AND SIGNAL MODEL Shrey Yadav School of Electrical Engineering
mode-division multiplexing (MDM) for adaptive multi-input-multi-output (MIMO) equalization to reduce for modal crosstalk and modal dispersion. To minimize computational complexity, use MIMO frequency-domain equalization (FDE).Polarization division multiplexing (PDM) system use single mode fiber but its transmission effected by noise, fiber nonlinearity and dispersion. In multi-mode fiber (MMF) with multi-input-multi-output (MIMO) transmission Increasing per-fiber capacity can be achieved more readily
technology is such developed that device may operate in TDD with one node and FDD with other node at the same time. For our case, we consider FDD as it is currently being used to a large extent. MIMO implementation in LTE MIMO techniques are essentially a major part in LTE framework.Some prominent features of MIMO which are very useful for LTE case are as follows- Transmit diversity: In this multiple antenna are used to transmit same block of code. the code is divided into 2 or 4 blocks. The numbers 2
The Merriam-Webster dictionary defines architecture as the art or science of designing and creating buildings. Almost all locations around the world have at least one or several buildings that are of historical significance or greatly admired. These buildings not only identify its citizens and government, but the state. Through architecture it’s safe to say that one can measure many things about the culture, lifestyle, creativity, and social structure. In this paper I will be comparing and contrasting
The following is expected from a microwave radio link when it is deployed (7) in a 4G network: Carry multiservice traffic over microwave links cost-effectively Increase the transport bandwidth capacity for data services Maximize the spectral efficiency Provide carrier grade manageability and survivability of multi-service transport In order to meet afore mentioned expectations, with an eye on 3Cs, is the biggest hurdle. The migration to all IP network is going to be a tedious transition (8)
Allison wanted to emit a purpose that wasting time, energy, and money on products that won’t benefit us is worthless. The purpose in engineering smarter technology, is finding out how it will help someone’s life. One product mentioned, was “The Mimo, a baby monitor built into a onesie”. She explained that it able to connect with other products based on the child that can help parents out but really all of it was just too much of a gimmick. A baby should live his life like every other baby, not