. A bar subjected to a stress of 1 GPa develops an elongation of 5mm. If the initial length of the bar is 1m, calculate the elastic modulus of the bar. b. The amount of strain energy per unit volume that a material can absorb without permanent deformation. c. What are the words to define the slope of the stress-strain diagram and the deformation per unit length?

. A bar subjected to a stress of 1 GPa develops an elongation of 5mm. If the initial length of the bar is 1m, calculate the elastic modulus of the bar. b. The amount of strain energy per unit volume that a material can absorb without permanent deformation. c. What are the words to define the slope of the stress-strain diagram and the deformation per unit length?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.6.7P: A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The...

See similar textbooks

Similar questions

A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
During stress-strain test, the unit deformation at a stress of 35 MPa was observed to be 167 x 10^-6 m/m and at a stress of 140 MPa it was 667 x 10^-6. If the proportional limit was 200 MPa, what is the modulus of Elasticity (GPa)? What is the strain corresponding to a stress of 80 MPa?
A 0.013 m diameter, 0.5 m long cylindrical metal bar is subjected to a compressive force of 8,500 N. This load does not exceed the yield strength of the material. Determine its diameter under this load. You will need some of the following properties of the metal to solve the problem: modulus of elasticity = 207 GPa, Poisson’s ratio = 0.30, yield strength = 180 MPa, tensile strength = 380 MPa, ductility = 23% elongation.
Figure 6.23 shows the tensile engineering stress– strain curve in the elastic region for a gray cast iron. Determine (a) the tangent modulus at 25 MPa (3625 psi) and (b) the secant modulus taken to 35 MPa (5000 psi).
(c) A piece of aluminum is pulled in tension from its original length of 202 mm with a stress of 172 MPa. If the modulus of elasticity for aluminum is 69 GPa and the deformation is entirely elastic, identify what will be the resultant elongation?
A 3/4 in. diameter circular cylindrical specimen is subjected to a 40 kN uniaxial tensile load. The change in length of the bar that initially had dimensions of 5 ft was 0.002 in, while the change in its diameter was 0.001 in. the sample is made of an isotropic, homogeneous, linear elastic material.Determine the material properties and yield strength if bar AB acquires an elastic strain energy of 150 in.lb.
A tensile force of 200 KN is applied on a 0.02-m diameter and.2-m long rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to 2.01 m. Assuming no permanent deformation occurs in that material, the modulus of elasticity (GPa) is?
A titanium alloy specimen with an elastic modulus of 107 GPa and 3.9 mm in original diameter will experience elastic deformation when applied to a tensile load of 2695.2 N. Calculate the maximum length the specimen would reach if the maximum allowable elongation is 0.4 mm.
A cylindrical specimen of some metal alloy having an elastic modulus of 101 GPa and an original cross-sectional diameter of 3.9 mm will experience only elastic deformation when a tensile load of 4633 N is applied. Calculate the maximum length of the specimen ( in mm) before deformation if the maximum allowable elongation is 0.31 mm.
Draw the tensile curves of the following materials, taking into account the appropriate elongation at break, modulus of elasticity and tensile stress, on the side stress-strain graph. a)Low carbon steel (Ecelik=200Gpa),(Syield=300MPa),(Stensile=400MPa) b)High carbon steel (Esteel=200GPa),(Stensile=700MPa) c)Aluminum (Ealuminum=70GPa), (Syield=200MPa),(Stensile=300MPa) d)Cast iron (Ecast iron=120GPa),(Stensile=200MPa)
Sketch a tensile member with (a) a rectangular crosssection, (b) a solid circular cross section, and (c) a circulartubecross section, and label the dimensions symbolically (e.g.,label the radius for the solid circular case). For each member, write out the definition of engineering stress in terms of the actual dimensions of the component. If therectangular member has dimensions of width and thicknessequal to 1 cm 0.3 cm, what would be the radius of a solidcircular member such that the stress is equal for an equaltensile load? If a tube has an outer radius equal to that ofthis same solid cylinder, what is the maximum inner radiussuch that the stress does not exceed 200% of the stress inthe solid cylinder?
If the axial rigidity of steel bar of 1m length is 200 x 107 N, what will be the axial flexibility of the bar?