.65 m .32 m .11 4 m .6 m .2 m 35° .3 m .2 m 37 m- FIGURE P6.37 Problems 37, 38, 50, 61, 72, 83, 94, 103, 111, and 119. 50. A package-moving device is shown in Figure P6.37. For the configuration illustrated, use the relative velocity method to analytically determine the linear velocity of the package as the crank rotates clock- wise at 80 rpm.

.65 m .32 m .11 4 m .6 m .2 m 35° .3 m .2 m 37 m- FIGURE P6.37 Problems 37, 38, 50, 61, 72, 83, 94, 103, 111, and 119. 50. A package-moving device is shown in Figure P6.37. For the configuration illustrated, use the relative velocity method to analytically determine the linear velocity of the package as the crank rotates clock- wise at 80 rpm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(STATIC OF RIGID BODIES) Centroid Show complete and step by step solution and detailed illustrations. Limit your answer into 3 decimal places.
A mass weighing 11.5 kg falls a distance of 1.5 m upon the top of a helical compression spring. Determine the force applied on the spring if it compressed 203mm. Please show your full solution with unit analysis. Subject: Machine Design
Dynamics of rigid bodies Problem 5
An electric elevator with a motor at the top has a multistrand cable weighing 8.4 lb/ft. When the car is on the first floor 270 feet of cable are paid out, and effectively 0 feet when the car is on the top floor. How much work does the motor do to lift an 1800 lb car and cable from the first floor to the top? Provide a picture model, give the approximate equation, then solve.
PROBLEM The diameter of two pulleys are (0.3m)and (0.2m), center distance (1m).if we use open belt drive. Determine: 1- the length of V-belt (2ß = 60°). 2- the contact angle between belt and smaller pulley. 3- the horse power, if the smaller pulley turn with speed (400r.p.m) and the tension force in tight side (T1=900N), coefficient of friction ų=0.3 4- the speed of large pulley.
! show Full Solution ! DYNAMICS OF RIGID BODIES *use given data below
The controlling force curve of a spring controlled governor is a straight line. The weight of each governor ball is 40 N and extreme radii of rotation are 10 cm and 17.5 cm. If the values of the controlling force at above radli are 205 N and 400 N respectively and friction of mechanism is equivalent to 2.5 N at each ball. Find The extreme equilibrium speeds of the governor. (1) The equilibrium speed and coefficienct of insensitiveness at a radius of 15 cm
As seen in the figure, three masses are connected to each other with the system set up on a table. Table friction and kinetic coefficient of friction is 0.35. (g = 10m / s2). b) Find the acceleration of each mass. c) Find the tensile forces on the ropes. d) How many meters will the object of 6kg go down after t = 3s after the system is released?
Figure below shows a mass-spring model of the type used to design packaging systems and vehicle suspensions, for example. The springs exert a force that is proportional to their compression, and the proportionality constant is the spring constant k. The two side springs provide additional resistance if the weight W is too heavy for the center spring. When the weight W is gently placed, it moves through a distance x before coming to rest. From statics, the weight force must balance the spring forces at this new position. (if x=d) These relations can be used to generate the plot of x versus W. (a) The following values are given: k1=104 N/m; k2 = 1.5 *104 N/m; d =0.1 m. Create a function that computes the distance x, using the input parameter W; Then, test your function for the following two cases, using the values: W=500 N W=2000 N. (b) Create another script and use your function to plot x versus W for 0 < W < 3000 N for the values of k1, k2, and d given in part a.
6.10 - This is a statics problem that deals with ‘Zero-Force Members’.
(STATIC OF RIGID BODIES) Show complete and step by step solution with detailed illustrations. Limit the answer into 2 decimal points.
Figure Q2 shows two configurations of a part sorting machine in a production process. Since the process involve high speed movement, the design engineer have proposed two configurations of design as shown in Figure Q2 (a) – Configuration 1 and Figure Q2 (b) – Configuration 2. The mass m1 and m2 are 180 kg and 70 kg respectively and the spring coefficient, k = k1 = k2 = k3 = k4 = 300 N/m.(a) Sketch the Free Body Diagram for each configuration (Configuration 1 and Configuration 2).(b)Construct the Equation of Motion for each configuration (Configuration 1 and Configuration 2).(c)Predict which configuration that would lead to the highest first natural frequency, ωn1. State the reason for your answer.(d)Validate your answer in Q2(c) by providing natural frequency ωn calculation for each configuration.