.A 2.17 x 10-5 M solution of X had A = 1.000 when measured at 400 nm, and A = 0.189 when measured at 450 nm. 3.21 x 10-4 M solution of Y had A = 0.069 at 400 nm and had A = 0.685 at 450 nm. bsorbance of the mixture of X and Y is 0.531 at both 400 and 450 nm. What are the concentrations f X and Y, if all measurements were carried out in a 1.00 cm spectral cell?

.A 2.17 x 10-5 M solution of X had A = 1.000 when measured at 400 nm, and A = 0.189 when measured at 450 nm. 3.21 x 10-4 M solution of Y had A = 0.069 at 400 nm and had A = 0.685 at 450 nm. bsorbance of the mixture of X and Y is 0.531 at both 400 and 450 nm. What are the concentrations f X and Y, if all measurements were carried out in a 1.00 cm spectral cell?

Chemistry & Chemical Reactivity

10th Edition

ISBN:9781337399074

Author:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Publisher:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Chapter3: Chemical Reactions

Section3.9: Classifying Reactions In Aqueous Solution

Problem 2.2ACP

See similar textbooks

Similar questions

The nickel level in a soil sample was determined using AAS. A 3.0 g sample was dissolved in acid and then diluted to a total volume of 100.0 mL. The absorbance of this solution determined at a wavelength of 232 nm, was found to be0.3. Several standard solutions were tested under the same conditions and a calibration curve shown below was obtained. Calculate the mass of nickel in mg.
A sample was prepared by diluting 1 mL of a sample to 5 mL. The resulting solution has an absorbance of 0.529. Based on the Beer's Law plot prepared for the compound, y = 1.8711x, what is the concentration of the original solution?
To prepare a standard solution of Mn2+, a 0.250 g sample of Mn is dissolved in 10 mL of concentrated HNO3 (measured with a graduated cylinder). The resulting solution is quantitatively transferred to a 100-mL volumetric flask and diluted to volume with distilled water. A 10-mL aliquot of the solution is pipeted into a 500-mL volumetric flask and diluted to volume.a. Express the concentration of Mn in mg/L, and estimate its uncertainty using a propagation of uncertainty.b. Can you improve the concentration’s uncertainty by using a pipet to measure the HNO3, instead of a graduated cylinder?
1. Sketch and label the main parts of the mass spectrometer. 2. Give detail description about how it works.
During your experiment, you measure the absorbance of a sample to be 1.362. You have to convert thisabsorbance to methylene blue concentration (in ppm) using the absorbance measurements of two standardsolutions of known concentration:5 ppm: Absorbance 0.55510 ppm: Absorbance 1.211What is, in ppm, the concentration of your sample? Report using 3 decimal figures. Your answer must becorrect to 0.02 ppm
Referring to the posted calibration curve (image attached) ...A 2.345 g sample of a ruthenium ore was dissolved and diluted to 100.00 mL. 4.000 mL of this sample was removed, treated appropriately, and diluted to 50.00 mL. This solution has an absorbance of 0.320. Calculate how many grams of ruthenium (MW = 101.07 g/mol) were in the sample.Select one:1.6 1.3 51 52 1.2
A medical lab technician creates a standard solutions of percent hemoglobin in whole blood. The technician measures the absorbance of each solution at 520 nm and creates a standard curve of the absorbance versus percent hemoglobin in whole blood and finds the linear equation below, with an R2 of 0.9985. y = 0.0523 x + 0.072 A patient sample has an absorbance of 0.162. Using the standard curve data, calculate the percent hemoglobin in the patient sample
A medical lab technician creates a standard solutions of percent hemoglobin in whole blood. The technician measures the absorbance of each solution at 520 nm and creates a standard curve of the absorbance versus percent hemoglobin in whole blood and finds the linear equation below, with an R2 of 0.9985. y=0.0523x+0.072 A patient sample has an absorbance of 0.915. Using the standard data curve data, calculate the percent hemoglobin in the sample
Referring to the posted calibration curve ...A 2.345 g sample of a ruthenium ore was dissolved and diluted to 100.00 mL. 4.000 mL of this sample was removed, treated appropriately, and diluted to 50.00 mL. This solution has an absorbance of 0.320. Calculate how many grams of ruthenium (MW = 101.07 g/mol) were in the sample.Select one:1.6 1.3 51 52 1.2
A medical lab technician creates a standard solutions of percent hemoglobin in whole blood. The technician measures the absorbance of each solution at 520 nm and creates a standard curve of the absorbance versus percent hemoglobin in whole blood and finds the linear equation below, with an R2 of 0.9985. y= 0.0523x + 0.072 A patient sample has an absorbance of 0.893. Using the standard curve data, calculate the percent hemoglobin in the patient sample.
A plot of Absorbance vs. molarity of Fe(SCN)2+ from part one of the lab gives a straight line with the following equation. y = 51x R2 = 0.998 If a student measures an absorbance value of 0.375 in the second part of the lab, what is the molarity of Fe(SCN)2+ in this solution?
Sample (μg) Absorbances (520 nm) Concentration 0.0 0.621 0 2.5 0.599 2.5 5.0 0.556 5 10.0 0.469 10 15.0 0.418 15 20.0 0.291 20 Plot a graph in which y axis represents for absorbance and x-axis represents for concentration From graph, y=mx + c Calculate the vitamin C concentrations of samples by the equation with consideration of dilution factors.